2018 MITSUBISHI ASX turn signal bulb

Indication lampsE00501600100Turn-signal indication lamps/
Hazard warning indication lamps
E00501700361
These indication lamps blink
in the following situations. •When the turn-signal
lever is moved to ac- tivate a turn-signal
lamp.
Refer to “Turn-signal
lever” on page 5-57.
• When the hazard
warning flasher switch is pressed toactivate the hazard
warning lamps.
Refer to “Hazard
warning flasher switch” on page
5-57.
• When the hazard
warning lamps auto- matically activate due
to sudden braking while driving.
Refer to “Emergency
stop signal system*”
on page 6-48.
NOTEl If these indication lamps blink too fast due
to any operation other than sudden braking,
the cause may be a blown lamp bulb or a faulty turn-signal connection.High-beam indication lamp
E00501800173
This indication lamp illumi-
nates when the high-beam is used.
Front fog lamp indication
lamp*
E00501900350
This lamp illuminates while the front fog lamps are on.
Rear fog lamp indication lamp
E00502001326
This lamp illuminates while
the rear fog lamp is on.
Position lamp indication lamp
E00508900173
This indication lamp illumi-
nates while the position lamps are on.
Diesel preheat indication lamp
(diesel-powered vehicles)
E00502300247
This indicates the glow plug
preheat condition.
[Except for vehicles equip-
ped with keyless operation system]
When the ignition switch is
turned to the “ON” position, the lamp illumi-
nates. As the glow plug becomes hot, the lamp goes out and the engine can be started.
[For vehicles equipped with keyless opera- tion system]
When the operation mode is put in ON, the
lamp illuminates and preheating of the glow lamp starts automatically. As the glow plugbecomes hot, the lamp goes out and the en-
gine starts.
NOTEl If the engine is cold, the diesel preheat indi-
cation lamp is on for a longer time.
Indication lamps
5-46OGAE18E1Instruments and controls5

Turn-signal leverE00506501592
1- Turn-signalsWhen making a normal turn, use posi-
tion (1). The lever will return automati-
cally when cornering is completed.
2- Lane-change signals When moving the lever to (2) slightly to
change a lane, the turn-signal lamps and
indication lamp in the instrument cluster
will only flash while the lever is operat-
ed.
Also, when you move the lever to (2)
slightly then release it, the turn-signal
lamps and indication lamp in the instru-
ment cluster will flash 3 times.
NOTEl If the lamp flashes unusually quickly, the
bulb in a turn-signal lamp may have burned out. We recommend you to have the vehicle
inspected.
l It is possible to activate the following func-
tions.
• Flashing of the turn-signal lamps when
the lever is operated with the ignition
switch or the operation mode is in ACC.
• Deactivate the turn-signal lamp 3-flash
function for lane changes.
• The time required to operate the lever for
the 3-flash function can be adjusted.
For further information, we recommend you
to consult a MITSUBISHI MOTORS Au-
thorized Service Point.Hazard warning flasher
switch E00506600860
Use the hazard warning flasher switch when
the vehicle has to be parked on the road for
any emergency.
The hazard warning flashers can always be operated, regardless of the ignition switch po-
sition or the operation mode.

Push the switch to turn on the hazard warning
flashers, all turn-signal lamps flash continu-
ously. To turn them off, push the switch
again.NOTEl While the hazard warning lamps are blinking
due to having manually pushed the switch, the emergency stop signal system does not
operate.
Refer to “Emergency stop signal system*” on page 6-48.
Turn-signal lever
5-57OGAE18E1Instruments and controls5

CAUTIONlIf the newly inserted fuse blows again after a
short time, we recommend you to have the electrical system checked to find the causeand rectify it.
l Never use a fuse with a larger capacity than
specified or a substitute (such as a cable or
foil). Doing so could cause the circuit wires
to overheat and create a fire.Replacement of lamp bulbs
E01003102248
Before replacing a bulb, ensure the lamp isoff. Do not touch the glass part of the new
bulb with your bare fingers; the skin oil left
on the glass will evaporate when the bulb gets hot and the vapour will condense on the
reflector and dim the surface.
CAUTIONl Bulbs are extremely hot immediately after
being turned off.
When replacing a bulb, wait for it to cool
sufficiently before touching it. You could otherwise be burnt.
l Do not install commercially available LED-
type bulbs.
Commercially available LED-type bulbs
could adversely affect the operation of the vehicle, such as by preventing the lamps andother vehicle equipment from operating
properly.NOTEl If you are unsure of how to carry out the
work as required, we recommend you to consult a specialist.
l Be careful not to scratch the vehicle body
when removing a lamp or lens.
l When it rains or when the vehicle has been
washed, the inside of the lens sometimes be-
comes foggy. This is the same phenomenon as when window glass mists up on a humid
day, and does not indicate a functional prob- lem.
When the lamp is switched on, the heat will
remove the fog. However, if water gathers inside the lamp, we recommend you to havethe lamp checked.Bulb location and capacity
E01003201574
CAUTIONl When replacing a bulb, be sure to use a new
bulb of the same type, wattage and colour. If
you install a different bulb, the bulb could malfunction or fail to come on and could
lead to a vehicle fire.Outside
E01003305267
1- Front turn-signal lamps: 21 W
(WY21W)
2- Headlamps, high-beam: 60 W (HB3) 3- Daytime running lamps *1
Position lamps (Type 2) *2
4- Front fog lamps *1
: 35 W (H8)
*1
If so equipped
Replacement of lamp bulbs
10-26OGAE18E1Maintenance10 Front

5-Headlamps, low beam Halogen: 55 W
(H11)
High intensity discharge *2
: 35 W (D2S)
5 W (W5W)
6- Position lamps: (Type 1) *1
5 W (W5W)
7- Side turn-signal lamps (on fender) *1
, *2
:
5 W
8- Side turn-signal lamps (on outside rear-
view mirror) *1
Codes in parentheses indicate bulb types.WARNINGl Check with a
MITSUBISHI MOTORS
Authorized Service Point when it is neces-
sary to repair a high intensity discharge headlamp or to replace the bulb.
High voltage is generated in the high in-
tensity discharge headlamp bulb and elec- trodes, which may cause a severe shock
when the bulb and connector are removed
or disconnected.*2 Have the lamps bulbs replaced at a
MITSUBISHI MOTORS Authorized
Service Point.
*1 If so equippedNOTEl An LED, not a bulb, is used in the daytime
running lamp/position lamp (Type 2) and the
side turn-signal lamp (on the outside rear- view mirror).
Contact a MITSUBISHI MOTORS Author-
ized Service Point when there is a need for
repair or replacement.
l For the side turn-signal lamp (on fender), it
is not possible to repair or replace just the bulb.
Contact a MITSUBISHI MOTORS Author-
ized Service Point when there is a need for
repair or replacement.
9- High-mounted stop lamp
10- Licence plate lamps: 5 W (W5W)
11- Rear fog lamp
12- Reversing lamps: 16 W (W16W) 13- Rear turn-signal lamps: 21 W (W21W)14- Stop and tail lamps
Codes in parentheses indicate bulb
types.NOTEl An LED, not a bulb, is used in the stop and
tail lamp, the high-mounted stop lamp and the rear fog lamp.
Contact a MITSUBISHI MOTORS Author-
ized Service Point when there is a need for
repair or replacement.Inside
E01003403570
1- Room lamp (rear)*: 8 W
2- Vanity mirror lamps*: 2 W
3- Room lamp (front) & map lamps: 8 W
4- Luggage room lamp: 5 W
5- Glove box lamp: 1.4 W
*: If so equipped
Replacement of lamp bulbs
10-27OGAE18E1Maintenance10 Rear

2.When replacing the bulb on the right
side of the vehicle in the case of diesel-
powered vehicles, remove the clips (B)
by prying with a straight blade (or mi- nus) screwdriver, and remove the side
cover.
*: Front of the vehicle
3. Turn the socket (C) anticlockwise to re-
move it.
*: Front of the vehicle
4. Pull the bulb out of the socket.
5. To install the bulb, perform the removal
steps in reverse.
Front turn-signal lamps
E01003800922
To remove 1. Remove the upper cover. For information regarding how to re-move the upper cover, refer to “Remov-
ing and installing the upper cover and duct” on page 10-10.
2. Remove the entire socket and bulb as-
sembly (A) by turning it anticlockwise.
*: Front of the vehicle
3. Remove the bulb by pulling it out.
To install 1. To install the bulb, perform the removal
steps in reverse.
Replacement of lamp bulbs
10-31OGAE18E1Maintenance10

2. Install the upper cover.For information regarding how to install
the upper cover, refer to “Removing and
installing the upper cover and duct” on page 10-10.Side turn-signal lamps (on
fender)*
E01003900516
NOTEl For the side turn-signal lamps (on fender), it
is not possible to repair or replace just thebulb.
Contact a MITSUBISHI MOTORS Author-
ized Service Point when there is a need for
repair or replacement.Side turn-signal lamps (on out-
side rear-view mirror)*
E01003900529
NOTEl An LED, not a bulb, is used in the side turn-
signal lamps (on outside rear-view mirror).
Contact a MITSUBISHI MOTORS Author-
ized Service Point when there is a need for
repair or replacement.Front fog lamps*
E01004003603
1. Remove the clip (A).
2. Insert a straight blade (or minus) screw-
driver with a cloth over its tip into the fog lamp cover (B) and pry gently to re-
move it.
3. Remove the screws (C) and remove the
lamp unit.NOTEl Except for vehicles equipped with daytime
running lamps, when unfastening the screws,be careful not to move the beam position ad-
justment screw (D).
Replacement of lamp bulbs
10-32OGAE18E1Maintenance10

Rear fog lamp
E01004101730
NOTElThe rear fog lamp uses an LED instead of a
bulb. Check with a MITSUBISHI MOTORS
Authorized Service Point when the lamp
needs to be repaired or replaced.Rear combination lamps
E01004203009
1. Remove the screws (A) that hold the
lamp unit and remove the lamp unit.
2. Turn the socket and bulb assembly anti-
clockwise to remove it.
B- Stop and tail lamp (LED) - cannot be
replaced
C- Rear turn-signal lamps
NOTEl An LED, not a bulb, is used in the stop
lamp/tail lamp. Contact a MITSUBISHI
MOTORS Authorized Service Point when
there is a need for repair or replacement.
3. Pull the bulb out of the socket.
4. To install the bulb, perform the removal
steps in reverse.NOTEl When mounting the lamp unit, align the
groove (D) on the lamp unit with the clip onthe body and the pin (E) on the unit with the
hole in the body.Reversing lamps
E01004401430
1. Open the tailgate.
2. Insert a straight blade (or minus) screw-
driver into the notch of the cover and pry
gently to remove the cover.
Replacement of lamp bulbs
10-34OGAE18E1Maintenance10

Electronic immobilizer (Anti-theftstarting system)................................................ 3-03
Electronically controlled 4WD system............. 6-39
Emergency starting............................................8-02
Emergency stop signal system.......................... 6-48
Engine specifications.......................................11-10
Engine switch.................................................... 3-13
Engine Coolant..............................................10-07,11-15
Number....................................................... 11-03
Oil............................................................... 10-05
Oil and oil filter........................................... 11-15
Overheating................................................... 8-04
Specifications.............................................. 11-10
Used engine oils safety instructions and disposal information............................. 2-06
Exterior and interior lamp operation............... 10-18
F
Fluid capacities and lubricants........................ 11-15
Fluid Automatic transmission fluid...................... 11-15
Brake fluid........................................ 10-09,11-15
Clutch fluid................................................. 10-09
Engine coolant.................................. 10-07,11-15
Washer fluid..................................... 10-08,11-15
For cold and snowy weather............................10-19
Forward Collision Mitigation System (FCM)... 6-59
Front fog lamps Bulb location and capacity.......................... 10-26Replacement................................................ 10-32
Switch........................................................... 5-58
Front room lamp
Bulb location and capacity............... 10-26,10-27
Front seat........................................................... 4-03
Front turn-signal lamps Bulb location and capacity.......................... 10-26
Replacement................................................ 10-31
Fuel consumption............................................ 11-12
Fuel
Filling the fuel tank....................................... 2-03Fuel selection................................................ 2-02
Modification/alterations to the electrical or fuel systems............................. 2-06
Tank capacity................................................ 2-03
Fuses................................................................ 10-19
Fusible links.................................................... 10-19
G
General maintenance....................................... 10-18
General vehicle data........................................ 11-04
Genuine parts.....................................................2-06
Glove box lamp Bulb location and capacity.......................... 10-27
H
Hazard warning flasher switch.......................... 5-57
Hazard warning indication lamps......................5-46
Head restraints................................................... 4-07
Headlamp levelling switch................................ 5-55
Headlamp washer switch...................................5-64
Headlamps Bulb location and capacity.......................... 10-26Headlamp flasher.......................................... 5-54Replacement..................................... 10-28,10-29
Switch........................................................... 5-50
Heated mirror.................................................... 6-12
Heated seats....................................................... 4-06
Heater................................................................ 7-03
High-mounted stop lamp Bulb location and capacity.......................... 10-26Replacement................................................ 10-36
Hill start assist................................................... 6-46
Hinges and latches lubrication........................ 10-19
Horn switch....................................................... 5-65
I
If the vehicle breaks down................................ 8-02
Ignition switch................................................... 6-12
Indication lamps................................................ 5-46
Information screen display................................ 5-48
Inside rear-view mirror......................................6-08
Inside tailgate release........................................ 3-31
Inspection and maintenance following rough road operation........................................ 6-43
Instruments........................................................ 5-02
Interior lamps.................................................... 7-73
J
Jack.................................................................... 8-07Storage.......................................................... 8-06
Jump starting (Emergency starting).................. 8-02
K
Key slot............................................................. 3-20
Keyless entry system.................................3-04,3-22
Alphabetical index
12- 2 OGAE18E1Alphabetical index