2018 MERCEDES-BENZ SL CLASS cooling

Problems with the rear window defroster Problem
Possible causes/consequences and P Solutions
The indicator lamp on
the l button flashes.
The rear window
defroster has deactiva-
ted prematurely or can-
not be activated. The on-board voltage is too low because too many electrical consum-
ers are switched on. X
Switch off any consumers that are not required, e.g. reading lamps,
interior lighting or the seat heating.
When the battery is sufficiently charged, the rear window defroster
can be activated again.
The roof is open. X
Close the roof.
When the roof is closed, the rear window defroster can be activated
again.
Switching air-recirculation mode
on/off
General notes If you switch on air-recirculation mode, the win-
dows can fog up more quickly, in particular at
low temperatures. Only use air-recirculation
mode briefly to prevent the windows from fog-
ging up.
Activating/deactivating X
Turn the SmartKey to position H in the igni-
tion lock ( Y
page 116).X
To activate: press the r button.
The indicator lamp in the r button lights
up.
i Air-recirculation mode is automatically acti-
vated at high levels of pollution (dual-zone
automatic climate control only) or at high out-
side temperatures. When air-recirculation
mode is activated automatically, the indicator
lamp in the r button is not lit. Outside air
is added after about 30 minutes. X
To deactivate: press the r button.
The indicator lamp in the r button goes
out. i Air-recirculation mode deactivates auto-
matically: R
after approximately five minutes at outside
temperatures below approximately 41 ‡
(5 †) R
after approximately five minutes if cooling
with air dehumidification is deactivated R
after approximately 30 minutes at outside
temperatures above approximately 41 ‡
(5 †) if the "Cooling with air dehumidifica-
tion" function is activated
Switching the residual heat on or off
General notes The residual heat function is only available on
vehicles for Canada.
It is possible to make use of the residual heat of
the engine to continue heating the stationary
vehicle for up to 30 minutes after the engine has
been switched off. The heating time depends on
the set interior temperature.
Activating/deactivating X
Turn the SmartKey to position

Workin gint he engine compartment poses a
risk of injury.
Where possible, let the engine cool down and
touch only the component sd escribed in the
following.
G WARNING
The cooling system is pressurized, particularly
when the motor is warm. If you open the cap,
you could be scalded if hot coolant sprays out.
There is ar isk of injury.
Let the engine cool down before you open the
cap. Wear gloves and eye protection. Slowly
open the cap to relieve pressure.
Example X
Park the vehicle on al evel surface.
Only check the coolant level when the vehicle
is on al evel surface and the engine has cooled
down. X
Turn the SmartKey to position H in the igni-
tion lock ( Y
page 116).
On vehicles with KEYLESS-GO, press the
Start/Stop button twice ( Y
page 116).X
Check the coolant temperature gage in the
multifunction display.
The coolant temperature must be below
158 ‡( 70 †).X
Turn the SmartKey to position

Model MB-Freigabe or
MB-Approval
All models
229.5
i MB approval is indicated on the oil contain-
ers.
Fillin gc apacitiesThe following values refer to an oil change
including the oil filter.
Model Capacity
SLC 300
6.7 US qt (6.3 l)
Mercedes-AMG
SLC 43 6.9 US qt (6.5 l)
Ad ditives
! Do not us ea ny additive sint he engine oil.
Thi sc ould damag et he engine.
Brake fluid
G WARNING
The brake fluid constantly absorb sm oisture
from the air. Thi sl owers the boiling point of
the brake fluid .Ift he boiling point of the brake
fluid is too low, vapor pockets may form in the
brake system when the brakes are applied
hard. Thi sw ould impai rb raking efficiency.
There is ar is kofana ccident.
Yo us houl dh av et he brake fluid renewe da t
the specified intervals.
Whe nh an dling brake fluid ,o bserve the impor-
tant safety notes on service products
( Y
page 290).
The brake fluid change interval sc an be found in
the Maintenance Booklet.
Only us eb rake fluid approved by Mercedes-
Benz in accordance with MB-Freigab eorM B-
Approva l3 31.0.
Information abou ta pp roved brake fluid can be
obtaine data ny qualified specialist worksho po r
on the Interne ta t
http://bevo.mercedes-benz.co m. i Have the brake fluid regularly replaced at a
qualified specialist workshop and the replace-
ment confirmed in the Maintenance Booklet.
Coolant
Importan ts afety notes
G WARNING
If antifreeze comes into contact with hot com-
ponents in the engine compartment, it may
ignite. There is ar isk of fire and injury.
Let the engine cool dow nb efore yo ua dd anti-
freeze .M ake sur et hat antifreeze is not spilled
next to the filler neck. Thoroughly clea nt he
antifreeze from components before starting
the engine.
! Only ad dc oolant that has bee np remixed
with the desire da ntifreeze protection. You
coul do therwise damag et he engine.
Furthe ri nformatio nonc oolants can be found
in the Mercedes-Benz Specifications for Ser-
vice Products, MB BeVo 310.1, e.g. on the
Internet at
http://bevo.mercedes-benz.com .Orc on-
tact aq ualifie ds pecialist workshop.
! Always use as uitabl ec oolant mixture, even
in countries where hig ht emperatures prevail.
Otherwise ,t he engine cooling system is not
sufficiently protected from corrosion and
overheating.
i Have the coolant regularly replaced at a
qualified specialist workshop and the replace-
ment confirmed in the Maintenance Booklet.
Comply with the important safety precautions
for service products whe nh andling coolant
( Y
page 290).
The coolant is am ixture of water and anti-
freeze/corrosion inhibitor. It is responsible for
the following: R
anti-corrosion protection R
antifreeze protection R
raising the boiling point
If the coolant has antifreeze protection dow nt o
-35 ‡( -3 7† ), the boiling point of the coolant
during operation is approximatel y2 66 ‡
(130 †).Service products and filling capacities 293
Technical data Z

The antifreeze/corrosion inhibitor concentra-
tion in the engine cooling system should: R
be at least 50%. This will protec tt he engine
cooling system against freezin gd own to
approximately -35 ‡( -37 †).R
not exceed 55% (antifreez ep rotection down
to -49 ‡[ -45 †]). Otherwise, heat will not be
dissipated as effectively
If the vehicle has lost coolant, add equal
amounts of water and antifreeze/corrosion
inhibitor.
Mercedes-Benz recommends an antifreeze/
corrosion inhibitor concentrate in accordance
with MB Specifications for Servic eP roducts
310.1.
i When the vehicle is first delivered, it is filled
with ac oolant mixture that ensures adequate
antifreeze and anti-corrosion protection.
i The coolant is checked with every mainte-
nanc ei nterval at aq ualified specialist work-
shop.
Fillin gc apacitiesMissing values were not availabl eatt ime of
going to print.
Model Capacity
SLC 300
Approx .8 .5 US qt
(8.0 l)
Mercedes ‑ Benz
SLC 43 AMG Approx .8 .2 US qt
(7.8 l)
Windshield washer system
Important safety notes
G WARNING
Windshield washer concentrate could ignite if
it comes into contact with hot engine compo-
nent sort he exhaust system. There is ar isk of
fire and injury.
Make sure that no windshield washer con-
centrate is spilled next to the filler neck.
! Only use washer fluid that is suitable for
plastic lamp lenses, e.g. MB SummerFit or MB
WinterFit. Unsuitable washer fluid could dam-
age the plastic lenses of the headlamps. ! Only MB SummerFit and MB WinterFit
washer fluid should be mixed together. The
spray nozzles may otherwise become
blocked.
Do not use distilled or de-ionised water. Other-
wise, the level sensor may give af alse reading.
When handling washer fluid, observe the impor-
tant safety notes on service products
( Y
page 290).
At temperatures above freezing: X
Fill the washer fluid reservoir with am ixture of
water and windshield washer fluid, e.g. MB
SummerFit. X
Add 1p art MB SummerFit to 100 parts water.
At temperatures below freezing: X
Fill the washer fluid reservoir with am ixture of
water and washer fluid, e.g. MB WinterFit.
For the correc tm ixing ratio refer to the infor-
mation on the antifreeze reservoir.
i Add windshield washer fluid, e.g. MB Sum-
merFit or MB WinterFit, to the washer fluid all
year round.
Climate control system refrigerant
Important safety notes The climate control system of your vehicle is fil-
led with refrigerant R ‑ 134a.
The instruction label regarding the refrigerant
type used can be found on the radiator cross
member.
! Only the refrigerant R ‑ 134a and the PAG oil
approved by Mercedes-Benz may be used.
The approved PAG oil may not be mixed with
any other PAG oil that is not approved for
R-134a refrigerant .O therwise, the climate
control system may be damaged.
Servic ew ork, such as refilling with refrigerant or
replacing component parts, may only be carried
out by aq ualified specialist workshop. All appli-
cable regulations, as well as SAE standard J639,
must be adhered to.
Always have work on the climate control system
carried out at aq ualified specialist workshop.294
Service products and filling capacities
Technical data