2018 MERCEDES-BENZ CLA lock

X
Insert the new bul bi nto bul bh older D .X
Insert bul bh older D and turn it clockwise.X
Press on housing cover C and turn it to the
right. X
Replace the cover in the front wheel housing
( Y
page 105).
High-beam headlamps/daytime run-
ning lamps/parking lamps and stand-
ing lamps (halogen headlamps) X
Switch off the lights. X
Open the hood. X
Turn housing cover C counter-clockwise and
remove it. X
Turn bul bh older D counter-clockwise and
pul lo ut.X
Insert the new bul ba nd engage it to the stop.X
Press on housing cover C and turn it to the
right.
Turn signals (halogen headlamps)
X
Switch off the lights. X
Open the hood. X
Turn bul bh older C counter-clockwise and
pul lo ut. X
Turn the bul bc ounter-clockwise and pul li t
out of bul bh older C .X
Insert the new bul bi nto bul bh older C .X
Insert bul bh older C and turn it clockwise
until it engages.
Replacing rear bulbs
Openin ga nd closing the side trim pan-
els
View of right-hand side trim panel
You must open the side trim panel in the trunk
before you can replace the bulbs in the tail
lamps. X
To open: release right or left side trim
panel C at the top and fold it down in the
direction of the arrow. X
To close: insert side panel C .
Tail lamps X
Switch off the lights. X
Open the trunk. X
Open the side trim panel ( Y
page 106).106
Replacing bulbs
Lights and windshield wipers

Replacing the wiper blades
Important safety notes
G WARNING
If the windshield wiper sb egin to move while
yo ua re changing the wiper blades, yo uc ould
be trapped by the wiper arm .T here is ar is ko f
injury.
Alway ss witch off the windshield wiper sa nd
ignition before changing the wiper blades.
! To avoid damaging the wiper blades, make
sure that yo ut ouch only the wiper arm of the
wiper.
! Neve ro pe nt he hoo difaw in dshield wiper
arm ha sb ee nf olded away from the wind-
shield.
Neve rf ol daw in dshield wiper arm withou ta
wiper blad eb ac ko nto the windshield.
Hol dt he windshield wiper arm firmly when
yo uc hange the wiper blade. If yo ur elease the
windshield wiper arm withou taw ip er blade
and it falls onto the windshield ,t he windshield
may be damaged by the force of the impact.
Mercedes-Benz recommend st hat yo uh av e
the wiper blades changed at aq uali fied spe-
cialist workshop.
Changin gt he windshield wiper blades
Removin gt he wiper bladesX
Vehicles without KEYLESS-GO or KEY-
LESS-G Os tart function: remove the Smart-
Key from the ignition lock. X
Vehicles with KEYLESS-GO or KEYLESS-
GO start function: switch off the engine.X
Fol dt he wiper arm away from the windshield. X
Hol dontot he wiper arm with one hand. With
the othe rh an d, turn wiper blad eind ir ection
of arrow C away from the wiper arm as far as
it will go. X
Slide catch D in the direction of arrow

instructions .Y ou will see the current settings
of the various climat ec ontrol functions.
DYNAMIC SELECT button (except
Mercedes-AM Gv ehicles)You can choose betwee nv arious drive programs
with the DYNAMI CS ELEC Tb utton
( Y
page 128).
If you have selected drive program E :R
when heating, the electrical heate rb ooster is
deactivate da nd in the warming-up phase
heat output is reduced R
the rear window defroster running tim ei s
reduced
Dependin gont he configuration, climat es et-
tings may also be influenced in the drive pro-
gram I .
If you have selected drive program C or S ,c li-
mate settings are not influenced.
ECO start/stop function Durin ga utomatic engin es witch-off, the climate
control system only operates at ar educed capa-
city. If you require the full climat ec ontrol output,
you can switc ho ff the ECO start/sto pf unction
by pressing the ECO button ( Y
page 127).
Operating th ec limate control sys-
tems
Activating/deactivating climate con-
trol
General notes When the climat ec ontrol is switched off ,t he air
supply and air circulation are also switched off.
The windows could fog up. Therefore, switc ho ff
climat ec ontrol only briefly
Air-conditioning system X
Turn the SmartKey to position H in the igni-
tion lock ( Y
page 122).X
To switch on: turn control

Problems with the "Cooling with air dehumidification" function Problem
Possible causes/consequences and P Solutions
The indicator lamp in the
Z button flashes
three times or remains
off. The "Cooling with air
dehumidification" func-
tion cannot be switched
on. Cooling with air dehumidification has been deactivated due to am al-
function. X
Visit aq ualified specialist workshop.
Setting climate control to automatic
General notes The automatic climate control function is only
available in conjunction with dual-zone auto-
matic climate control.
In automatic mode, the set temperature is main-
tained automatically at ac onstant level. The
system automatically regulates the temperature
of the dispensed air, the airflow and the air dis-
tribution.
The "Cooling with air dehumidification" function
is activated automatically in automatic mode.
Setting climate control to automatic X
Turn the SmartKey to position 2 in the ignition
lock ( Y
page 122).X
Set the desired temperature. X
To activate: press the X button.
The indicator lamp in the X button lights
up. Automatic air distribution and airflow are
activated. X
To switch to manua lm ode: press the O
or J button.
or X
Press the

i You can also activate several air distribution
settings simultaneously. To do this ,p ress
multiple air distribution buttons .T he air is
the nd irected through various vents.
i Regardless of the air distribution setting,
airflow is always directed through the side air
vents. The side air vents can only be close di f
the adjusters are turned clockwise until they
engage.
Setting th ea ir distributionX
Turn the SmartKey to position H in the igni-
tion lock ( Y
page 122).X
Press one or more of the

If the battery voltage is too low, the rear window
defroster may switch off.
Activating/deactivating X
Turn the SmartKey to position H in the igni-
tion lock ( Y
page 122). X
Press the l button.
The indicator lamp in the l button lights
up or goes out.
Problems with the rear window defroster Problem
Possible causes/consequences and P Solutions
The rear window
defroster has deactiva-
ted prematurely or can-
not be activated. The battery has not been sufficiently charged. X
Switch off any consumers that are not required, e.g. reading lamps,
interior lighting or the seat heating.
When the battery is sufficiently charged, the rear window defroster
can be activated again.
Switching air-recirculatio nm ode
on/off
General notes You can deactivate the flow of fresh air if
unpleasant odors are entering the vehicle from
outside. The air already inside the vehicle will
then be recirculated.
If you switch on air-recirculation mode, the win-
dows can fog up more quickly, in particular at
low temperatures. Only use air-recirculation
mode briefl ytop revent the window sf rom fog-
ging up.
The operation of air-recirculation mode is the
same for all control panels.
Activating/deactivating X
Turn the SmartKey to position H in the igni-
tion lock ( Y
page 122).X
To activate: press the

i If you activate the residual heat function at
high temperatures, only the ventilation wil lb e
activated. The blower runs at mediu ms peed.
i You cannot use the ventilation to cool the
vehicle interior to at emperature lowe rt han
the outsid et emperature.
Activating/deactivating X
Turn the SmartKey to position Z in the igni-
tion lock or remove it ( Y
page 122).X
Press the K button.
The indicator lamp in the K button lights
up or goes out.
The indicator lamp in the button indicates that
the respective function is activated.
i Residua lh eat is deactivated automatically:R
after approximately 30 minutes R
when the ignition is switched on R
if the battery voltage drops
Air vents
Important safety notes
G WARNING
Very hot or very cold air can flow from the air
vents. This could resul tinb urns or frostbite in
the immediate vicinity of the air vents. There
is ar isk of injury.
Make sure that all vehicle occupants always
maintain as ufficient distance to the air out-
lets. If necessary ,r edirect the airflow to
another area of the vehicle interior.
In order to ensure the direct flow of fresh air
through the air vents into the vehicle interior,
please observe the following notes: R
keep the air inlet between the windshield and
the hood free of blockages, such as ice, snow
or leaves. R
never cover the air vents or air intake grilles in
the vehicle interior.
i For optimal climate control in the vehicle,
open the air vents completely and set the
adjusters to the central position. Setting the air vents
C
Side window defroster vent D
Side air vent X
To open as ide air vent: turn the adjuster in
side air vent D to the left. X
To close as ide air vent: turn the adjuster in
side air vent D clockwise as far as it wil lg o.
i The center and rear air vents are adjusted in
the same way.120
Ai rv ents
Climate control

! Do not warm up the engine with the vehicle
stationary. Drive off immediately .A void high
engine speeds and driving at full throttle until
the engine has reached its operating temper-
ature.
Only shift the automatic transmission to the
desired drive position when the vehicle is sta-
tionary.
Where possible ,a void spinning the drive
wheels when pulling awa yons lippery roads.
You could otherwise damage the drive train.
! Mercedes-AMG vehicles: avoid full-load
operation and engine speeds greater than
5000 rpm when the engine is cold. This helps
to protect the engine and avoids uncomfort-
able driving.
Key positions
SmartKey
Z
To remove the SmartKey
(shift the transmission to position ] )G
Power suppl yf or some consumers, such as
the windshiel dw ipersH
Ignition (power suppl yf or all consumers)
and drive position
I
To start the engine
i The SmartKey can be turned in the ignition
lock even if it is not the correct SmartKey for
the vehicle. The ignition is not switched on.
The engine cannot be started. Start/Stop button General notes Vehicles with KEYLESS-GO are equipped with
SmartKeys featuring the integrated KEYLESS-
GO function and ad etachable Start/Stop but-
ton.
Ac heck which periodically establishes ar adio
connection between the vehicle and the Smart-
Key determines whether av alid SmartKey is in
the vehicle. This occurs, for example, when
starting the engine.
When you insert the Start/Stop button into the
ignition lock, the system needs approximately
two seconds recognition time. You can then use
the Start/Stop button.
Pressing the Start/Stop button several times in
succession corresponds to the different Smart-
Key positions in the ignition lock. This is only the
case if you are not depressing the brake pedal.
If you depress the brake pedal and press the
Start/Stop button, the engine starts immedi-
ately.
To start the vehicle without actively using the
SmartKey: R
the Start/Stop button must be inserted in the
ignition lock R
the SmartKey must be in the vehicle R
the vehicle must not be locked with the
SmartKey or KEYLESS-GO ( Y
page 71)
Do not keep the KEYLESS-GO key: R
with electronic devices, e.g. am obile phone
or another SmartKey. R
with metallic objects, e.g. coins or metal foil. R
inside metallic objects, e.g. am etal case.
This can affect the functionality of KEYLESS-GO.
If you lock the vehicle with the SmartKey remote
control or with KEYLESS-GO, after as hort time:R
you will not be able to switch on the ignition
with the Start/Stop button. R
you will no longer be able to start the engine
with the Start/Stop button until the vehicle is
unlocked again.
If you lock the vehicle centrally using the button
on the front door ( Y
page 76), you can continue
to start the engine with the Start/Stop button.
The engine can be switched off while the vehicle
is in motion by pressing and holding the Start/
Stop button for three seconds. This function122
Driving
Driving and parking