2018 MAZDA MODEL CX-9 Maintenance and Care

•To prevent corrosion on bright-metal
surfaces, apply wax or chrome
preservative and rub it to a high luster.
•During cold weather o r in coastal areas,
cover bright-metal parts with a coating
of wax or preservative heavier than
usual. It would also help to coat them
with noncorrosive petroleum jelly or
some other protective compound.
CAUTION
Do not use steel wool, abrasive cleaners, or
strong detergents containing highly
alkaline or caustic agents on
chrome-plated or anodized aluminum
parts. This may result in damage to the
protective coating and cause discoloration
or paint deterioration.
▼ Underbody Maintenance
Road chemicals and salt used for ice and
snow removal and solvents used for dust
control may collect on the underbody. If
not removed, they will speed up rusting
and deterioration of such underbody parts
as fuel lines, frame, floor pan, and exhaust
system, even though these parts may be
coated with anti-corrosive material.

Thoroughly flush the underbody and
wheel housings wit
h lukewarm or cold
water at the end of each winter. Try also to
do this every month.

Pay special attention to these areas
because they easily hide mud and dirt. It
will do more harm than good to wet
down the road grime without removing
it.

The lower edges of doors, rocker panels,
and frame members have drain holes that
should not be clogged. Water trapped there
will cause rusting.
WA R N I N G
Dry off brakes that have become wet by
driving slowly, releasing the accelerator
pedal and lightly applying the brakes
several times until the brake performance
returns to normal:
Driving with wet brakes is dangerous.
Increased stopping distance or the vehicle
pulling to one side when braking could
result in a serious accident. Light braking
will indicate whether the brakes have been
affected.
▼ Aluminum Wheel Maintenance
A protective coating is provided over the
aluminum wheels. Special care is needed
to protect this coating.
CAUTION
Do not use any detergent other than mild
detergent. Before using any detergent,
verify the ingredients. Otherwise, the
product could discolor or stain the
aluminum wheels.
Maintenance and Care
Appearance Care
6-64
CX-9_8GC3-EA-17G_Edition1
2017-5-29 10:13:38

NOTE
•Do not use a wire brush or any abrasive
cleaner, polishing compound, or solvent
on aluminum wheels. They may damage
the coating.
•Always use a sponge or soft cloth to
clean the wheels.
Rinse the wheels thoroughly with
lukewarm or cold water. Also, be sure to
clean the wheels after driving on dusty
or salted roads to help prevent
corrosion.
•Avoid washing your vehicle in an
automatic car wash that uses high-speed
or hard brushes.
▼ Plastic Part Maintenance
•When cleaning the plastic lenses of the
lights, do not use g
asoline, kerosene,
rectified spirit, paint, thinner, highly
acidic detergents, or strongly alkaline
detergents. Otherwise, these chemical
agents can discolor or damage the
surfaces resulting in a significant loss in
functionality. If plastic parts become
inadvertently exposed to any of these
chemical agents, flush with water
immediately.
•If plastic parts such as the bumpers
become inadvertently exposed to
chemical agents or fluids such as
gasoline, oil, engine coolant, or battery
fluid, it could cause discoloration,
staining, or paint peeling. Wipe off any
such chemical agents or fluids using a
soft cloth immediately.
•High water temperature and high water
pressure car washers are available
depending on the type of high pressure
car washer device. If the car washer
nozzle is put too close to the vehicle or
aimed at one area for an extended period
of time, it could deform plastic parts or
damage the paint.
•Do not use wax containing compounds
(polish). Otherwise, it could result in
paint damage.
•In addition, do not use an electrical or
air tool to apply wax. Otherwise, the
frictional heat generated could result in
deformation of plastic parts or paint
damage.
Maintenance and Care
Appearance Care
6-65
CX-9_8GC3-EA-17G_Edition1 2017-5-29 10:13:38

Interior Care
WA R N I N G
Do not spray water into the vehicle cabin:
Spraying water into the vehicle cabin is
dangerous as electrical devices such as the
audio and switches could get wet resulting
in a malfunction or vehicle fire.
NOTE
•Do not wipe the interior using alcohol,
chlorine bleach, or organic solvents
such as thinner, benzene, and gasoline.
Otherwise, it may cause discoloration or
stains.
•Rubbing hard with a stiff brush or cloth
may cause damage.
If the vehicle interio r becomes soiled by
any of the following, wipe it off
immediately using a soft cloth.
Leaving it uncleaned could cause
discoloration, stains, cracks, or peeling of
the coating, and it will make it hard to
wipe off later.
•Beverage or fragrance
•Grease or oil
•Soiling
▼ Seat Belt Maintenance
1. Clean the soiled area by lightly
dabbing it with a soft cloth soaked in a
mild detergent (approx. 5%) diluted
with water.
2. Wipe off the remaining detergent using
a cloth soaked in clean water and
wrung out well.
3. Before retracting se at belts which have
been pulled ou t for cleaning, dry them
off thoroughly and make sure there is
no remaining moisture on them.
WA R N I N G
If a seat belt appears frayed or has
abrasions, have it replaced by an
Authorized Mazda Dealer:
If a seat belts is used under such a
condition, it cannot function at its full
capacity which could result in serious injury
or death.
Use a mild detergent to remove soiling
from a seat belt:
If organic solvents are used for cleaning the
seat belts or they become stained or
bleached, there is the possibility of them
becoming weakened and as a result, they
may not function at their full capacity
which could cause serious injury or death.
NOTE
Clean seat belts diligently if they get dirty.
Leaving them uncleaned will make it
difficult to clean them later, and it may
affect the smooth retracting of the seat
belt.
▼ Vinyl Upholstery Maintenance
Remove dust and dirt from the vinyl
upholstery using a brush or vacuum.
Remove soiling from vinyl upholstery
using a leather and vinyl upholstery
cleaner.
Maintenance and Care
Appearance Care
6-66
CX-9_8GC3-EA-17G_Edition1
2017-5-29 10:13:38

▼Upholstery Maintenance
1. Clean the soiled area by lightly
dabbing it with a soft cloth soaked in a
mild detergent (approx. 5%) diluted
with water.
2. Wipe off the remaining detergent using a cloth soaked in clean water and
wrung out well.
▼Leather Upholstery Maintenance*
1. Remove dust and sand using a vacuum
cleaner.
2. Wipe off the soiled area with a soft cloth and a suitable, special cleaner or
a soft cloth soaked in a mild detergent
(about 5%) diluted with water.
3. Wipe off the remaining detergent using a cloth soaked in clean water and
wrung out well.
4. Remove moisture with a dry, soft cloth and allow the leather to further dry in a
well-ventilated, shaded area. If the
leather gets wet such as from rain,
remove the moisture and dry it as soon
as possible.
NOTE
•Because genuine leather is a natural
material, its surface is not uniform and
it may have natural scars, scratches,
and wrinkles.
•To maintain the quality for as long as
possible, periodical maintenance, about
twice a year, is recommended.
•If the leather upholstery comes into
contact with any of the following, clean
it immediately.
Leaving it uncleaned could cause
premature wear, mold, or stains.
•Sand or dirt
•Grease or oil, such as hand cream
•Alcohol, such as in cosmetic or hair
dressing items
•If the leather upholstery gets wet,
promptly remove moisture with a dry
cloth. Remaining moisture on the
surface may cause deterioration such as
hardening and shrinkage.
•Exposure to direct sunlight for long
periods may cause deterioration and
shrinkage. When parking the car under
direct sunlight for long periods, shade
the interior using sunshades.
•Do not leave vinyl products on the
leather upholstery for long periods.
They may affect the leather quality and
coloring. If the cabin temperature
becomes hot, the vinyl may deteriorate
and adhere to the genuine leather.
Maintenance and Care
Appearance Care
*Some models.6-67
CX-9_8GC3-EA-17G_Edition1 2017-5-29 10:13:38

▼Plastic Part Maintenance
CAUTION
Do not use polishing agents.
Depending on the product ingredients,
they could cause discoloration, stains,
cracks or peeling of the coating.
▼Instrument Panel Top Maintenance
1. Wipe the soiled area with a soft cloth
soaked in a mild detergent (approx.
5%) diluted with water.
2. Wipe off the remaining detergent using
a cloth soaked in clean water and
wrung out well.
▼Panel Maintenance
If a panel becomes soiled, wipe it off with
a soft cloth soaked in clean water and
thoroughly wrung out.
If some areas require further cleaning, use
the following procedure:
1. Wipe the soiled area with a soft cloth
soaked in a mild detergent (approx.
5 %) diluted with water.
2. Wipe off the remaining detergent using a cloth soaked in clean water and
wrung out well.
NOTE
Be particularly careful when cleaning
shiny surface panels and metallic parts
such as plating as they can be scratched
easily.
▼Active Driving Display
Maintenance*
The dust-proof sheet has a coating. When
cleaning, do not use a hard or
rough-surface cloth, o
r cleaning detergent.
In addition, if a chemical solvent gets on
the active driving d isplay, wipe it off
immediately. The dust-proof sheet could
be damaged and the surface coating could
be scratched. Use a fine, soft cloth such as
those used for cleaning eyeglasses.
NOTE
Use of compressed air when cleaning the
dust-proof sheet is recommended.
▼ Cleaning the Window Interiors
If the windows become covered with an
oily, greasy, or waxy film, clean them with
glass cleaner. Follow
the directions on the
container.
CAUTION
 Do not scrape or scratch the inside of the
window glass. It could damage the
thermal filaments and the antenna lines.
 When washing the inside of the window
glass, use a soft cloth dampened in
lukewarm water, gently wiping the
thermal filaments and the antenna lines.
Use of glass cleaning products could
damage the thermal filaments and the
antenna lines.
Maintenance and Care
Appearance Care
6-68*Some models.
CX-9_8GC3-EA-17G_Edition1 2017-5-29 10:13:38

▼Cleaning the Floor Mats
Rubber floor mats should be cleaned with
mild soap and water only.
WA R N I N G
Do not use rubber cleaners, such as tire
cleaner or tire shine, when cleaning rubber
floor mats:
Cleaning the rubber
floor mats with rubber
cleaning products makes the floor mats
slippery.
This may cause an accident when
depressing the accelerator or brake pedal
or when getting in or out of the vehicle.
After removing the floor mats for
cleaning, always reinstall them securely
(page 3-50).
Maintenance and Care
Appearance Care
6-69
CX-9_8GC3-EA-17G_Edition1 2017-5-29 10:13:38

Index
Towing hooks.............................. 7-28
Emission Control System..................3-30
Ending Screen Display......................4-78
Engine Coolant.........................................6-27
Engine compartment overview.... 6-24
Exhaust gas.................................. 3-31
Hood release............................ .... 6-22
Oil................................................ 6-25
Starting...........................................4-5
Engine Coolant Temperature
Gauge................................................ 4-15
Essential Information.......................... 6-2
Event Data Recorder......................... 8-22
Exhaust Gas...................................... 3-31
Exterior Care..................................... 6-60 Aluminum wheel maintenance.... 6-64
Bright-metal maint enance........... 6-63
Maintaining the finish................. 6-61
Plastic part maintenance.............. 6-65
F
Flasher
Hazard warning........................... 4-61
Headlights.................................... 4-49
Flat Tire............................................... 7-3 Mounting the spare tire............... 7-15
Removing a flat tire.....................7-11
Floor Mat.......................................... 3-50
Fluid Brake............................................6-29
Washer......................................... 6-29
Fluids Classification................................. 9-4
Fog Lights......................................... 4-54
Foot Brake.........................................4-66
Forward Sensing Camera (FSC)..... 4-145
Front Seat............................................ 2-5
Fuel Filler lid and cap......................... 3-32
Gauge........................................... 4-16
Requirements............................... 3-29
Tank capacity.................................9-5
Fuel Consumption Display............... 4-78
Fuel Economy Monitor..................... 4-77
Ending screen display................. 4-78
Fuel consumption display............4-78
Fuses.................................................. 6-53 Panel description......................... 6-56
Replacement................................ 6-53
G
Gauges............................................... 4-12
Glove Compartment........................ 5-100
H
Hazardous Driving............................ 3-49
Hazard Warning Flasher....................4-61
HeadlightsComing home light......................4-52
Control......................................... 4-49
Headlight flashing....................... 4-52
High-low beam............................ 4-52
Leaving home light..................... 4-52
Leveling....................................... 4-53
Head Restraint................................... 2-18
High Beam Control System
(HBC)................................................ 4-88 High Beam Control System (HBC)
indicator light (green)..................4-90
Hill Launch Assist (HL A)................ 4-70
HomeLink Wireless Control
System............................................... 4-62
Hood Release............. ....................... 6-22
Horn...................................................4-61
I
If a Warning Light Turns On or
Flashes............................................... 7-30
10-4
CX-9_8GC3-EA-17G_Edition1 2017-5-29 10:13:38

Index
If the Active Driving Display Does Not
Operate.............................................. 7-53
IgnitionSwitch............................................ 4-4
Ignition Not Switched Off (STOP)
Warning Beep.................................... 7-49
Illuminated Entry System................. 5-95
Immobilizer System.......................... 3-44
Indication/Indicator L ights................4-35
Indicator Lights
Low engine coolant
temperature.................................. 4-39
Wrench......................................... 4-39
Inspecting Brake Fluid Level............ 6-29
Inspecting Coolant Leve l.................. 6-27
Inspecting Engine Oil Level............. 6-27
Inspecting Washer Fluid Level......... 6-29
Instrument Cluster...... ....................... 4-12
Interior Care...................................... 6-66
Active driving display
maintenance................................. 6-68
Cleaning the floor mats............... 6-69
Cleaning the window interiors.....6-68
Instrument panel top
maintenance................................. 6-68
Leather upholstery
maintenance................................. 6-67
Panel maintenance....................... 6-68
Plastic part maintenance.............. 6-68
Seat belt maintenance..................6-66
Upholstery maintenan ce.............. 6-67
Vinyl upholstery maintenance..... 6-66
Interior Lights................................... 5-92 Luggage compartment light.........5-92
Map lights....................................5-92
Overhead lights............................5-92
i-ACTIVSENSE................................ 4-84
Active safety tec hnology............. 4-84
Adaptive Front Lighting System
(AFS)........................................... 4-87Advanced Smart City Brake Support
(Advanced SCBS)..................... 4-134
Blind Spot Monitoring (BSM).....4-91
Camera and sensors..................... 4-85
Distance Recognition Support System
(DRSS).......................................4-104
Forward Sensing Camera
(FSC)......................................... 4-145
High Beam Control System
(HBC).......................................... 4-88
Lane-keep Assist System (LAS) &
Lane Departure Warning System
(LDWS)..................................... 4-123
Mazda Radar Cruise Control with
Stop & Go function (MRCC with
Stop & Go function).................. 4-110
Pre-crash safety technology.........4-85
Radar sensors (rear)...................4-153
Radar sensor (front)...................4-150
Rear Cross Traffic Alert
(RCTA)...................................... 4-107
Smart Brake Support (SBS)...... 4-142
Smart City Brake Support
(SCBS)....................................... 4-138
Traffic Sign Recognition System
(TSR)........................................... 4-97
i-ACTIV AWD Operation.................4-81
J
Jack...................................................... 7-4
Jump-Starting.................................... 7-21
K
Keyless Entry System......................... 3-3
Keys.....................................................3-2
Key suspend function.................... 3-9
Transmitter.............. .......................3-4
Key Left-in-luggage Compartment
Warning beep (With the advanced
keyless function)............................... 7-49
10-5
CX-9_8GC3-EA-17G_Edition1 2017-5-29 10:13:38