2018 Lexus LC500 jump start

393
7
-$@-$I@0.@0.&@ &&

7-2. Steps to take in an emergency
When trouble arises
The glove box can be opened by per-
forming the following operations after
unlocking the doors.
If the glove box is locked, unlock it with the
mechanical key. ( P.293)
1Remove the cover using a flathead
screwdriver.
To prevent damage to the cover, cover the tip of the screwdriver with a rag.
2 Push the flathead screwdriver into
the part shown in the illustration to
open the glove box.
■After opening the glove box
The glove box can be opened normally by closing the glove box after restarting the
engine .
If you have a set of jumper (or booster)
cables and a second vehicle with a 12-
volt battery, you can jump start your
vehicle using the following procedure.
1 Confirm that the electronic key is
being carried.
When connecting the jumper (or booster) cables, depending on the situation, the
alarm may activate and doors locked. ( P.77)
NOTICE
■When installing the cover in the cen- ter of the rear seat
Make sure that the seat belts are not caught in the cover. Failure to do so may cause damage to the cover installation
clip and make it impossible to install the cover.
Opening the glove box
Restarting the engine system>

394
-$@-$I@0.@0.&@ &&

7-2. Steps to take in an emergency
2Open the hood (P.316) and
open the fuse box cover.
Push the tab in an d lift the lid off.
LC500 (Left-hand drive vehicles)
LC500 (Right-hand drive vehicles)
LC500h (Left-hand drive vehicles)
LC500h (Right-hand drive vehi-
cles)
3 Open the exclusive jump starting
terminal cover.
LC500 (Left-hand drive vehicles)
LC500 (Right-hand drive vehicles)

397
7
-$@-$I@0.@0.&@ &&

7-2. Steps to take in an emergency
When trouble arises
LC500h (Right-hand drive vehicles)
Exclusive jump starting terminal (your vehicle)
Positive (+) battery terminal (second vehicle)
Negative (-) battery terminal (second vehicle)
Solid, stationary, unpainted metallic point away from the exclusive jump starting
terminal and any moving parts as shown in the illustration
5 Start the engine of the second vehi-
cle. Increase the engine speed
slightly and maintain at that level for
approximately 5 minutes to
recharge the 12-volt battery of your
vehicle.
6 Open and close any of the door of
your vehicle with the engine switch
off.
7 Maintain the engine speed of the
second vehicle and start the engine
of your vehicle by
turning the engine switch switch> to IGNITION ON mode
.
8 Once the vehicle’s engine system> has started, remove the
jumper cables in the exact reverse
order from which they were con-
nected.
9 Close the exclusive jump starting
terminal cover, and reinstall the fuse
box cover to tits original position.
Once the engine starts, have the vehicle inspected at any autho-rized Lexus retailer or Lexus authorized
repairer, or any reliable repairer as soon as possible.
■Starting the engine when the 12-volt battery is discharged
The engine cannot be started by push-starting.
■To prevent 12-volt battery discharge
●Turn off the headlights and the audio sys-tem while the engine is
stopped.
●Turn off any unnecessary electrical com-
A
B
C
D

400
-$@-$I@0.@0.&@ &&

7-2. Steps to take in an emergency
1Stop the vehicle in a safe place and
turn off the air conditioning system,
and then stop the engine.
2 If you see steam:
Carefully lift the hood after the
steam subsides.
If you do not see steam:
Carefully lift the hood.
3 After the engine has cooled down
sufficiently, inspect the hoses and
WARNING
■After recharging the 12-volt battery
Have the 12-volt battery inspected at any authorized Lexus retailer or Lexus authorized repairer, or any reliable
repairer as soon as possible. If the 12-volt battery is deteriorating, continued use may cause the 12-volt battery to emit a
malodorous gas, which may be detri- mental to the health of passengers.
■When exchanging the 12-volt battery
After exchanging, securely attach the exhaust hose and exhaust hole plug to
the exhaust hole of the exchanged 12- volt battery. If not properly installed, gases (hydrogen) may leak into the vehi-
cle interior, and there is the possible dan- ger of the gas igniting and exploding.
NOTICE
■When handling jumper cables
When connecting the jumper cables, ensure that they do not become entan-gled in the cooling fan or engine drive
belt.
■To prevent damaging the vehicle
The exclusive jump starting terminal is to be used when charging the 12-volt bat-tery from another vehicle in an emer-
gency. It cannot be used to jump start another vehicle.
If your vehi cle overheats
(LC500)
The following may indicate that
your vehicle is overheating.
 The engine coolant temperature
gauge ( P.88) is in the red zone
or a loss of engine power is expe-
rienced. (For example, the vehicle
speed does not increase.)
 “Engine Coolant Temp High” is
shown on the multi-information
display.
 Steam comes out from under the
hood.
Correction procedures