2018 Lexus LC500 steering wheel

225
4
-$@-$I@0.@0.&@ &&

4-5. Using the driving support systems
Driving
If a different warning message is displayed, follow the instructions displayed on the screen.
■Customization
The following settings can be changed.
For how to change settings, refer to P.423.“Lane Keep-
ing Assist
Unavailable”
The LKA system is tempo-
rarily canceled due to a
malfunction in a sensor
other than the camera
sensor.
 Turn the LKA system
off and follow the appro-
priate troubleshooting
procedures for warning
messages. Afterward,
drive the vehicle for a
short time, and then turn
the LKA system back on.
“Lane Keep-
ing Assist
Unavailable
Below
Approx
50km/h”
The LKA system cannot
be used as the vehicle
speed is less than approxi-
mately 50 km/h (32
mph).
 Drive the vehicle at
approximately 50 km/h
(32 mph) or more.
“Lane Keep-
ing Assist
Unavailable at
Current
Speed”
The LKA system cannot
be used as the vehicle
speed is too high.
 Slow down.
FunctionSetting details
Lane depar-
ture alert
function
Adjust alert sensitivity
Steering
assist function
Turn steering wheel assis-
tance on and off
Warning mes-
sageDetails/Actions
Vehicle sway
warning func-
tion
Turn function on and off
Adjust alert sensitivity
Lane center-
ing functionTurn function on and off
FunctionSetting details

229
4
-$@-$I@0.@0.&@ &&

4-5. Using the driving support systems
Driving
change the set unit of the meter. Adjust the set unit of the meter to the speed unit of signs in the current location. ( P.423)
■Turning the system on/off
1 Select on of the
multi-information display ( P.92)
2 Press “OK” on the steering wheel.
■Speed limit sign display
If the engine switch

was last turned off while a speed limit sign was dis-played on the multi-information display, the
same sign displays again when the engine switch is turned to IGNI-TION ON mode .
■Customization
Setting (e.g. speeding warning threshold) can be changed.
(Customizable feature: P.423)
*:If equipped
■Meter display
Display
Set speed
Indicators
Dynamic radar cruise con-
trol with full-speed range*
In vehicle-to-vehicle distance con-
trol mode, the vehicle automati-
cally accelerates, decelerates and
stops to match the speed changes
of the preceding vehicle even if the
accelerator pedal is not depressed.
In constant speed control mode,
the vehicle runs at a fixed speed.
Use the dynamic radar cruise con-
trol with full-speed range on free-
ways and highways.
 Vehicle-to-vehicle distance con-
trol mode ( P.232)
 Constant speed control mode
( P.236)
System components
A
B
C

238
-$@-$I@0.@0.&@ &&

4-5. Using the driving support systems
becomes available again.
■Warning messages and buzzers for dynamic radar cruise control with full-speed range
Warning messages and buzzers are used to indicate a system malfun ction or to inform
the driver of the need for caution while driv- ing. If a warning mess age is shown on the multi-information display, read the message
and follow the instructions.
■When the sensor may not be correctly detecting the vehicle ahead
In the case of the following and depending on the conditions, operate the brake pedal when deceleration of the system is insuffi-
cient or operate the accelerator pedal when acceleration is required.
As the sensor may not be able to correctly detect these types of vehicles, the approach warning ( P.235) may not be activated.
●Vehicles that cut in suddenly
●Vehicles traveling at low speeds
●Vehicles that are not moving in the same
lane
●Vehicles with small rear ends (trailers with no load on board, etc.)
●Motorcycles traveling in the same lane
●When water or snow thrown up by the
surrounding vehicles hinders the detect- ing of the sensor
●When your vehicle is pointing upwards (caused by a heavy load in the luggage compartment, etc.)
●Preceding vehicle has an extremely high ground clearance
■Conditions under which the vehicle-to-vehicle distance control mode may not function correctly
In the case of the following conditions, operate the brake pedal (or accelerator
pedal, depending on the situation) as nec- essary.
As the sensor may not be able to correctly detect vehicles ahead, the system may not operate properly.
●When the road curves or when the lanes
are narrow
●When steering wheel operation or your
position in the lane is unstable

262
-$@-$I@0.@0.&@ &&

4-5. Using the driving support systems
■ECB (Electronically Controlled
Brake System)
The electronically controlled system
generates braking force correspond-
ing to the brake operation
■ABS (Anti-lock Brake System)
Helps to prevent wheel lock when the
brakes are applied suddenly, or if the
brakes are applied while driving on a
slippery road surface
■Brake assist
Generates an increased level of brak-
ing force after the brake pedal is
depressed when the system detects a
panic stop situation
■VSC (Vehicle Stability Control)
Helps the driver to control skidding
when swerving suddenly or turning on
slippery road surfaces
■Secondary Collision Brake (if
equipped)
When the airbag sensor detects a colli-
sion, the brakes and brake lights are
automatically controlled to reduce the
vehicle speed and that helps reduce
the possibility of further damage due to
a secondary collision.
■TRC (Traction Control)
Helps to maintain drive power and pre-
vent the drive wheels from spinning
when starting the vehicle or accelerat-
ing on slippery roads
■Hill-start assist control
Helps to reduce the backward move-
ment of the vehicle when starting on an
uphill
■VGRS (Variable Gear Ratio Steer-
ing) (if equipped)
Adjusts the front wheel turning angle in
accordance with the vehicle speed and
steering wheel movement
■DRS (Dynamic Rear Steering) (if
equipped)
Contributes to the turning characteris-
tics and responsiveness of the vehicle
by slightly adjusting the rear wheel
angle of the vehicle in accordance with
steering wheel movement.
■EPS (Electric Power Steering)
Employs an electric motor to reduce
the amount of effort needed to turn the
steering wheel
■AVS (Adaptive Variable Suspen-
sion System)
By independently controlling the
damping force of the shock absorbers
for each of the 4 wheels according to
Driving assist systems
To keep driving safety and perfor-
mance, the following systems oper-
ate automatically in response to
various driving situations. Be aware,
however, that these systems are
supplementary and should not be
relied upon too heavily when oper-
ating the vehicle.
Summary of the driving assist
systems

263
4
-$@-$I@0.@0.&@ &&

4-5. Using the driving support systems
Driving
the road and driving conditions, this
system helps riding comfort with supe-
rior vehicle stability, and helps good
vehicle posture
Also, the damping force changes
depending on the selected driving
mode. ( P.242)
■LDH (Lexus Dynamic Handling
system) (if equipped)
Provides integrated control of the
VGRS, DRS and EPS. Contributes to
turning characteristics at low speeds,
responsiveness at medium speeds and
safety at high speeds by controlling the
steering angle of the front and rear
wheels in accordance with the steering
wheel operation and vehicle speed.
■VDIM (Vehicle Dynamics Inte-
grated Management)
Provides integrated control of the
ABS, brake assist, TRC, VSC, hill-start
assist control, EPS, VGRS (if
equipped) and DRS (if equipped) sys-
tems
Helps to maintain vehicle stability when
swerving on slippery road surfaces by
controlling the brakes, engine system> output, steering assist (if
equipped), and steering ratio (if
equipped)
■Emergency brake signal
When the brakes are applied suddenly,
the stop lights automatically flash to
alert the vehicle behind
■When the TRC/VSC/ABS systems are operating
The slip indicator light will flash while the TRC/VSC/ABS systems are operating.
■Disabling the TRC system
If the vehicle gets stuck in mud, dirt or snow,
the TRC system may reduce power from the engine to the wheels.
Pressing the switch to turn the sys-
tem off may make it easier for you to rock
the vehicle in order to free it.
To turn the TRC system off, quickly press
and release the switch.
The “Traction Control Turned Off” will be
shown on the multi-information display.
Press the switch again to turn the sys-
tem back on.
■Disabling both TRC and VSC systems
To turn the TRC and VSC systems off, press
and hold the switch for more than 3
seconds while the vehicle is stopped.
The VSC OFF indicator light will come on and the “Traction Cont rol Turned Off” will
be shown on the multi-information display.*

264
-$@-$I@0.@0.&@ &&

4-5. Using the driving support systems
Press the switch again to turn the sys-
tems back on.*: On vehicles with PCS (Pre-Collision Sys-
tem), PCS will also be disabled (only Pre-
Collision warning is available). The PCS
warning light will come on and a message
will be displayed on the multi-information
display. ( P.217)
■When the message is displayed on the multi-information display showing that
TRC has been disabled even if the
switch has not been pressed
TRC cannot be operated. Contact any
authorized Lexus retailer or Lexus autho- rized repairer, or any reliable repairer.
■Operating conditions of hill-start assist control
When the following four conditions are met, the hill-start assist control will operate:
●The shift position is in a position other than P or N (when starting off for-
ward/backward on an upward incline).
●The vehicle is stopped.
●The accelerator pedal is not depressed.
●The parking brake is not engaged.
■Automatic system cancelation of hill- start assist control
The hill-start assist control will turn off in any of the following situations:
●The shift position is shifted to P or N.
●The accelerator pedal is depressed.
●The parking brake is engaged.
●2 seconds at maximum elapsed after the brake pedal is released
■VGRS is disabled when
VGRS may stop operating in the following situations.
In this event, the steering wheel may move from its straight forward position, but it will
return when the system restarts.
●When the steering wheel is operated for
an extended period of time while the vehicle is stopped or is moving very slowly (on vehicles with LDH, DRS is dis-
abled together with VGRS)
●When the steering wheel has been held
fully to the left or right
The center position of the steering wheel
may change when VGRS is disabled. How- ever, the position will return to normal after VGRS is reactivated.
■When the 12-volt battery is discon-
nected (vehicles with VGRS)
The steering wheel may move from its
straight forward position, but this will be corrected automatically when driving.
■Sounds and vibrations caused by the ABS, brake assist, TRC, VSC, hill-start
assist control and VGRS systems
●A sound may be heard from the engine
compartment when the brake pedal is depressed repeatedly, when the engine is started or just after the
vehicle begins to move. This sound does not indicate that a malfunction has occurred in any of these systems.
●Any of the following conditions may
occur when the above systems are oper- ating. None of these indicates that a mal-function has occurred.
• Vibrations may be felt through the vehicle body and steering.• A motor sound may be heard after the
vehicle comes to a stop.
■ECB operating sound
ECB operating sound may be heard in the
following cases, but it does not indicate that a malfunction has occurred.
●Operating sound heard from the engine compartment when the brake pedal is operated.
●Motor sound of the brake system heard from the front part of the vehicle when
the driver’s door is opened.
●Operating sound heard from the engine
compartment when one or two minutes passed after the stop of the engine .

265
4
-$@-$I@0.@0.&@ &&

4-5. Using the driving support systems
Driving
■EPS, VGRS and DRS operation sound
When the steering wheel is operated, a
motor sound (whirring sound) may be heard. This does not indicate a malfunction.
■Automatic reactivation of TRC and VSC systems
After turning the TRC and VSC systems off, the systems will be automatically re-
enabled in the following situations:
●When the engine switch
is turned off
●If only the TRC system is turned off, the
TRC will turn on when vehicle speed increases
If both the TRC and VSC systems are turned off, automatic re-enabling will not occur when vehicle speed increases.
■Secondary Collision Brake operating
conditions
The vehicle speed is approximately 10 km/h
(6 mph) or more and the airbag sensor detects a collision. (The Secondary Colli-sion Brake will not operate when the vehicle
speed is below approximately 10 km/h [6 mph].)
■Secondary Collision Brake automatic
cancellation
The Secondary Collision Brake is automati-
cally canceled in the following situations:
●The vehicle speed drops below approxi-
mately 10 km/h (6 mph)
●A certain amount of time elapses during
operation
●The accelerator pedal is depressed a
large amount
■If “Check Secondary Collision Brake system” is displayed on the multi-infor-mation display
The system may be malfunctioning. Have the vehicle inspected at any authorized
Lexus retailer or Lexus authorized repairer, or any reliable repairer.
■Reduced effectiveness of the EPS sys-tem
The effectiveness of the EPS system is
reduced to prevent the system from over- heating when there is frequent steering input over an extended period of time. The
steering wheel may feel heavy as a result. Should this occur, refrain from excessive steering input or stop the vehicle and turn
the engine off. The EPS sys- tem should return to normal within 10 min-utes.
■Operating conditions of emergency
brake signal
When the following three conditions are
met, the emergency brake signal will oper- ate:
●The emergency flashers are off.
●Actual vehicle speed is over 55 km/h
(35 mph).
●The brake pedal is depressed in a manner
that cause the system to judge from the vehicle deceleration that this is a sudden braking operation.
■Automatic system cancelation of emer-
gency brake signal
The emergency brake sign al will turn off in
any of the following situations:
●The emergency flashers are turned on.
●The brake pedal is released.
●The system judges from the vehicle deceleration that is not a sudden braking
operation.
WARNING
■The ABS does not operate effectively when
●The limits of tire gripping performance have been exceeded (such as exces-
sively worn tires on a snow covered road).
●The vehicle hydroplanes while driving at high speed on wet or slick roads.

269
4
-$@-$I@0.@0.&@ &&

4-6. Driving tips
Driving
Use fluids that are appropriate to
the prevailing outside temperatures.
•Engine oil
•Engine coolant
• Power control unit coolant (LC500h)
•Washer fluid
 Have a service technician inspect
the condition of the 12-volt battery.
 Have the vehicle fitted with four
snow tires.
Ensure that all tires are the specified size
and the same brand.
 Tire chains can only be installed on
the rear tires. However, tire chains
cannot be installed on 275/35RF21
or 275/40RF20 rear tires.
Before installing tire ch ains, change all four
tires and wheels to those of the specified
size for use with tire chains (front tires:
245/45RF20, rear tires: 245/45RF20,
wheels: 20 x 8 1/2 J 25 inset). Use the
specified type of tire chains and install
them on the rear tires only.
For details, contact any authorized Lexus
retailer or Lexus authorized repairer, or
any reliable repairer.
Winter driving tips
Carry out the necessary prepara-
tions and inspections before driving
the vehicle in winter. Always drive
the vehicle in a manner appropriate
to the prevailing weather condi-
tions.
Preparation for winter
WARNING
■Driving with snow tires
Observe the following precautions to
reduce the risk of accidents.
Failure to do so may result in a loss of
vehicle control and cause death or seri- ous injury.
●Use tires of the specified size.
●Maintain the recommended level of air pressure.
●Do not drive at speeds in excess of the
speed limit or the speed limit specified for the snow tires being used.
●Use snow tires on all, not just some wheels.
■Driving with tire chains
Observe the following precautions to reduce the risk of accidents.
Failure to do so may result in the vehicle being unable to be driven safely, and may
cause death or serious injury.
●Do not drive in excess of the speed limit specified for the tire chains being used, or 50 km/h (30 mph), which-
ever is lower.
●Avoid driving on bumpy road surfaces or over potholes.
●Avoid sudden acceleration, abrupt steering, sudden braking and shifting
operations that cause sudden engine braking.
●Slow down sufficiently before entering a curve to ensure that vehicle control is
maintained.
●Do not use LKA (Lane-Keeping Assist) system. (if equipped)