2018 KIA STONIC tow

This gauge indicates the temperature
of the engine coolant when the ignition switch or Engine Start/Stop button is
ON.
CAUTION
If the gauge pointer moves beyondthe normal range area toward theL

Non-operational conditions of
rear parking assist system
The rear parking assist systemmay not operate properly when:
1. Moisture is frozen to the sensor. (Itwill operate normally when the
moisture has been cleared.)
2. The sensor is covered with foreign matter, such as snow or water, or
the sensor cover is blocked. (It will
operate normally when the materi‐
al is removed or the sensor is no
longer blocked.)
3. Driving on uneven road surfaces (unpaved roads, gravel, bumps, gra‐ dient).
4. Objects generating excessive noise (vehicle horns, loud motorcycle en‐
gines, or truck air brakes) are with‐
in range of the sensor.
5. Heavy rain or water spray exists.
6. Wireless transmitters or mobile phones are within range of the
sensor.
7. The sensor is covered with snow.
8. Trailer towing.
The detecting range may decreasewhen:
1. The sensor is stained with foreign matter such as snow or water. (The
sensing range will return to normal
when removed.)
2. Outside air temperature is ex‐ tremely hot or cold.
The following objects may not berecognized by the sensor:
1. Sharp or slim objects such as ropes,chains or small poles.
2. Objects which tend to absorb the sensor frequency such as clothes,
spongy material or snow.
3. Undetectable objects smaller than 1 m (40 in.) in height and narrower
than 14 cm (6 in.) in diameter.
Rear parking assist system
precautions
• The rear parking assist system may not sound consistently depending on
the speed and shapes of the objects detected. • The rear parking assist system may
malfunction if the vehicle bumper
height or sensor installation has been
modified or damaged. Any non-fac‐
tory installed equipment or accesso‐ ries may also interfere with the sen‐
sor performance.
• The sensor may not recognize ob‐ jects less than 30 cm (12 in.) from
the sensor, or it may sense an incor‐
rect distance. Use caution.
• When the sensor is frozen or stained with snow, dirt, or water, the sensor
may be inoperative until the stains
are removed using a soft cloth.
• Do not push, scratch or strike the sensor. Sensor damage could occur.
NOTICE
This system can only sense objects
within the range and location of the
sensors; It can not detect objects in
other areas where sensors are not
installed. Also, small or slim objects,
such as poles or objects located be‐
(Continued)

4-77
4
Features of your vehicle

The high beam indicator will light when
the headlight high beams are switched on. To prevent the battery from being
discharged, do not leave the lights on
for a prolonged time while the engine is not running.
WARNING
Do not use high beam when thereare other vehicles. Using high beamcould obstruct the other driver's vi‐sion.
¥
5ZQF
"
To flash the headlights, pull the lever
towards you. It will return to the nor‐ mal (low beam) position when released.
The headlight switch does not need to
be on to use this flashing feature .
Turn signals and lane change
signals
¥
5ZQF
"
¥
5ZQF
#
Features of your vehicle
4-84

High beam Assist (if equipped)
0:#
The High Beam Assist is a system that
automatically adjusts the headlamp range (switches between high beam
and low beam) according to the bright‐
ness of other vehicles and road condi‐ tions.
Operating condition
1. Place the light switch in the AUTO position.
2. Turn on the high beam by pushing the lever away from you.
The High Beam Assist (
) indicator
will illuminate. 3. The High Beam Assist will turn on
when vehicle speed is above 45 kph(28 mph). • If the lever is pushed away when the High Beam Assist is operat‐
ing, the High Beam Assist will
turn off and the high beam will
be on continuously. The High
Beam Assist (
) indicator will
turn off.
• If the lever is pulled towards you when the high beam is on with
operating High Beam Assist, theHigh Beam Assist will turn off.
4. If the light switch is placed to the headlamp position, the High Beam
Assist will turn off and the low
beam will be on continuously.
The high beam switches to low beam in
the below conditions. - When the High Beam Assist is off.
- When the light switch is not in the AUTO position.
- When the headlamp is detected from the on-coming vehicle.
- When the tail lamp is detected from the front vehicle.
- When the surrounding is bright enough high beams are not needed. - When streetlights or other lights are
detected.
- When vehicle speed is below 35 km/h (22 mph).
- When headlamp/taillamp of bicycle/ motorcycle is detected.CAUTION
The system may not operate nor‐mally in the below conditions.•When the light from the on-com‐ing or front vehicle is not detectedbecause of lamp damage, hiddenfrom sight, etc.
•When the lamp of the on-comingor front vehicle is covered withdust, snow or water.
•When the light from the on-com‐ing or front vehicle is not detectedbecause of exhaust fume, smoke,fog, snow, etc.
•When the front window is coveredwith foreign matters such as ice,dust, fog, or is damaged.
•When there is a similar shape lampwith the front vehicle’s lamps.
(Continued)
Features of your vehicle
4-88

(Continued)
•When it is hard to see because offog, heavy rain or snow.
•When the headlamp is not repairedor replaced at an authorized deal‐er.
•When headlamp aiming is notproperly adjusted.
•When driving on a narrow curvedroad or rough road.
•When driving downhill or uphill.
•When only part of the vehicle infront is visible on a crossroad orcurved road.
•When there is a traffic light, re‐flecting sign, flashing sign or mir‐ror.
•When the road conditions are badsuch as being wet or covered withsnow.
•When the front vehicle’s head‐lamps are off but the fog lampson.
•When a vehicle suddenly appearsfrom a curve.
(Continued)
(Continued)
•When the vehicle is tilted from aflat tire or being towed.
•When the LDWS (lane departurewarning system) or LKAS (lanekeeping assist system) warninglight illuminates. (if equipped)
WARNING
•Do not place any accessories,stickers or tint the windshield.
•Have the windshield glass replacedfrom an authorized dealer.
•Do not remove or impact relatedparts of the High Beam Assist sys‐tem.
•Be careful that water doesn’t getinto the High Beam Assist unit.
•Do not place objects on the dash‐board that reflects light such asmirrors, white paper, etc. The sys‐tem may malfunction if sunlight isreflected.
(Continued)
(Continued)
•At times, the High Beam Assistsystem may not work properly, al‐ways check the road conditions foryour safety. When the systemdoes not operate normally, man‐ually change between the highbeam and low beam.

4-89
4
Features of your vehicle

(Continued)
age to system parts could occur andmay not be covered by your vehiclewarranty.When starting the vehicle in winter,set the wiper switch in the off posi‐tion. Otherwise, wipers may operateand ice may damage the windshieldwiper blades. Always remove allsnow and ice and defrost the wind‐shield properly prior to operating thewindshield wipers.
Windshield washers (front)
In the O (Off) position, pull the lever
gently toward you to spray washer flu‐ id on the windshield and to run the wip‐
ers 1-3 cycles.
Use this function when the windshield
is dirty.
The spray and wiper operation will con‐ tinue until you release the lever.
If the washer does not work, check the
washer fluid level. If the fluid level is
not sufficient, you will need to add ap‐ propriate non-abrasive windshield
washer fluid to the washer reservoir.
The reservoir filler neck is located in
the front of the engine compartment on the passenger side.
CAUTION
To prevent possible damage to thewasher pump, do not operate thewasher when the fluid reservoir isempty.
WARNING
Do not use the washer in freezingtemperatures without first warmingthe windshield with the defrosters;the washer solution could freeze onthe windshield and obscure your vi‐sion.
CAUTION
•To prevent possible damage to thewipers or windshield, do not oper‐ate the wipers when the wind‐shield is dry.
•To prevent damage to the wiperblades, do not use gasoline, kero‐sene, paint thinner, or other sol‐vents on or near them.
(Continued)
Features of your vehicle
4-92

Mode selection
The mode selection knob controls the
direction of the air flow through the ventilation system.
Air can be directed to the floor, dash‐
board outlets, or windshield. Five sym‐
bols are used to represent Face, Bi-Lev‐
el, Floor, Floor-Defrost and Defrost air position.
Face-Level (B, D)
Air flow is directed toward the upper
body and face. Additionally, each outlet can be controlled to direct the air dis‐
charged from the outlet.
Bi-Level (B, D, C, E)
Air flow is directed towards the face
and the floor.
Floor-Level (C, E, A, D)
Most of the air flow is directed to the
floor, with a small amount of the air being directed to the windshield and
side window defrosters.
Floor/Defrost-Level (A, C, D,E)
Most of the air flow is directed to the floor and the windshield with a small
amount directed to the side window
defrosters.
Defrost-Level (A, D)
Most of the air flow is directed to the
windshield with a small amount of air directed to the side window defrosters.
Instrument panel vents
0:#
The outlet vents can be opened or
closed separately using the thumb‐ wheel. To close the vent, rotate it
downward to the maximum position.
Also, you can adjust the direction of air
delivery from these vents using the vent control lever as shown.

4-101
4
Features of your vehicle

Floor & Defrost (A, C, D, E)
Most of the air flow is directed to the
floor and the windshield with a small amount directed to the side window
defrosters.
Face-Level (B, D)
Air flow is directed toward the upper
body and face. Additionally, each outlet can be controlled to direct the air dis‐
charged from the outlet.
Bi-Level (B, D, C, E)
Air flow is directed towards the face
and the floor.
Floor-Level (C, A, D, E)
Most of the air flow is directed to the
floor, with a small amount of the air being directed to the windshield and
side window defrosters.
Defrost mode
When you select the defrost mode, the
following system settings will be made automatically: • The air conditioning system will be turned on.
• The outside (fresh) air position will be selected.
• The fan speed will be set to the high speed.
To turn the defrost mode off, press the mode button or defrost button again or
AUTO button.
Instrument panel vents
0:#
The outlet port can be opened or closed
separately using the horizontal thumb‐ wheel. To close the vent, rotate it
downward to the maximum position. To
open the vent, rotate it upward to the
desired position.
Also, you can adjust the direction of air
delivered from these vents using the
vent control lever as shown.

4-111
4
Features of your vehicle