2018 KIA STONIC clock

SymbolFuse rat‐ingCircuit Protected
10ABCM (Body Control Module), Crash Pad Switch, FCA Unit, Lane Departure Warning System, BLIND-
SPOT DETECTION WARNING Radar LH/RH
15AEngine Room Junction Block(Back-Up Lamp Switch), Sport Mode Switch, Speed Sensor, Stop Lamp
Switch, Speed Sensor (In/Out), Transaxle Range Switch
LH25A Power Window Main Switch, Passenger Power Window Switch(RHD)
SPARE25A Spare
10A Rear Fog Lamp Relay
15A Clock Spring
LH7.5A Head Lamp LH, License Lamp LH(Sedan), Rear Combination Lamp (IN) LH(Wagon)
7.5A Front Console Switch, Front Seat Warmer Control Module, Audio, Audio / Video & Navigation Head
Unit, Head Lamp Leveling Device Actuator LH/RH, Air Conditioner Control Module, Electro Chromic
Mirror, Crash Pad Switch, DC-DC Converter, Clock Spring, A/T Shift Lever Indicator
7.5A
Engine Room Junction Block(Multipurpose Check Connector), ABS/ESC (Electronic Stability Control)
Control Module
10A Smart Key Control Module, Stop Lamp Switch
SPARE15A Spare
15A Front Fog Lamp Relay
7.5AEngine Room Junction Block(Air Conditioner Blower Relay), GSL Junction Block(PTC Heater Relay),
DSL Junction Block(Start Relay, Air Conditioner Blower Relay), Air Conditioner Control Module
MODULE510AEngine Room Junction Block(Head Lamp High Relay, Head Lamp Relay), Front Seat Warmer Control
Module, BCM (Body Control Module)


8-85
8
Maintenance

Side repeater lamp (bulb type)
bulb Replacement
1. Remove the lamp assembly fromthe vehicle by prying the lens and
pulling the assembly out.
2. Disconnect the bulb electrical con‐ nector.
3. Separate the socket and the lens parts by turning the socket coun‐
terclockwise until the tabs on the
socket align with the slots on the
lens part.
4. Remove the bulb by pulling it straight out.
5. Insert a new bulb in the socket. 6. Reassemble the socket and the
lens part.
7. Connect the bulb electrical connec‐ tor.
8. Reinstall the lamp assembly to the body of the vehicle.
Headlamp (Low/High beam) bulb
replacement (Headlamp Type A)
0:##
1. Open the hood.
2. Remove the headlamp bulb coverby turning it counterclockwise.
3. Disconnect the headlamp bulb socket-connector. 4. Remove the bulb-socket from the
headlamp assembly by turning the
bulb-socket counterclockwise until
the tabs on the bulb-socket align
with the slots on the headlamp as‐
sembly.
5. Install a new bulb-socket assembly in the headlamp assembly by align‐
ing the tabs on the bulb-socket
with the slots in the headlamp as‐
sembly. Push the bulb-socket into
the headlamp assembly and turn
the bulb-socket clockwise.
6. Install the headlamp bulb cover by turning it clockwise.
Headlamp bulb

8-109
8
Maintenance

WARNING
nHalogen bulbs
•Halogen bulbs contain pressurizedgas that will produce flying piecesof glass if broken.
•Always handle them carefully, andavoid scratches and abrasions. Ifthe bulbs are lit, avoid contactwith liquids. Never touch the glasswith bare hands. Residual oil maycause the bulb to overheat andburst when lit.A bulb should be operated onlywhen installed in a headlight.
•If a bulb becomes damaged orcracked, replace it immediatelyand carefully dispose of it.
•Wear eye protection when chang‐ing a bulb. Allow the bulb to cooldown before handling it.
Front turn signal lamp bulb
replacement (Headlamp Type A)
0:##
1. Open the hood.
2. Remove the bulb-socket from theheadlamp assembly by turning the
bulb-socket counterclockwise until
the tabs on the bulb-socket align
with the slots on the headlamp as‐
sembly.
3. Remove the bulb from the bulb- socket by pressing it in and rotat‐
ing it counterclockwise until the tabs on the bulb align with the slots
in the bulb-socket. Pull the bulb out
of the bulb-socket. 4. Insert a new bulb by inserting it in‐
to the bulb-socket and rotating it
until it locks into place.
5. Install the socket in the headlamp assembly by aligning the tabs on
the bulb-socket with the slots in
the assembly. Push the bulb-sock‐
et into the headlamp assembly and
turn the socket clockwise.
Position lamp / Day time
running lamp bulb replacement
(Headlamp Type A)
0:##
1. Open the hood.
Maintenance
8-110

2. Remove the bulb-socket from theheadlamp assembly by turning the
bulb-socket counterclockwise until
the tabs on the bulb-socket align
with the slots on the headlamp as‐
sembly.
3. Remove the bulb from the bulb- socket by pressing it in and rotat‐
ing it counterclockwise until the tabs on the bulb align with the slots
in the bulb-socket. Pull the bulb out
of the bulb-socket.
4. Insert a new bulb by inserting it in‐ to the bulb-socket and rotating it
until it locks into place.
5. Install the socket in the headlamp assembly by aligning the tabs on
the bulb-socket with the slots in
the assembly. Push the bulb-sock‐
et into the headlamp assembly and
turn the socket clockwise.Headlamp (Low/High beam) bulb
replacement (Headlamp Type B)
0:##
1. Open the hood.
2. Remove the headlamp bulb cover by turning it counterclockwise.
3. Disconnect the headlamp bulb socket-connector.
4. Remove the bulb-socket from the headlamp assembly by turning the
bulb-socket counterclockwise until
the tabs on the bulb-socket align
with the slots on the headlamp as‐
sembly. 5. Install a new bulb-socket assembly
in the headlamp assembly by align‐
ing the tabs on the bulb-socket
with the slots in the headlamp as‐
sembly. Push the bulb-socket into
the headlamp assembly and turn
the bulb-socket clockwise.
6. Install the headlamp bulb cover by turning it clockwise.
Headlamp bulb

8-111
8
Maintenance

WARNING
nHalogen bulbs
•Halogen bulbs contain pressurizedgas that will produce flying piecesof glass if broken.
•Always handle them carefully, andavoid scratches and abrasions. Ifthe bulbs are lit, avoid contactwith liquids. Never touch the glasswith bare hands. Residual oil maycause the bulb to overheat andburst when lit.A bulb should be operated onlywhen installed in a headlight.
•If a bulb becomes damaged orcracked, replace it immediatelyand carefully dispose of it.
•Wear eye protection when chang‐ing a bulb. Allow the bulb to cooldown before handling it.
Front turn signal lamp bulb
replacement (Headlamp Type B)
0:##
1. Open the hood.
2. Remove the bulb-socket from theheadlamp assembly by turning the
bulb-socket counterclockwise until
the tabs on the bulb-socket align
with the slots on the headlamp as‐
sembly.
3. Remove the bulb from the bulb- socket by pressing it in and rotat‐
ing it counterclockwise until the tabs on the bulb align with the slots
in the bulb-socket. Pull the bulb out
of the bulb-socket. 4. Insert a new bulb by inserting it in‐
to the bulb-socket and rotating it
until it locks into place.
5. Install the socket in the headlamp assembly by aligning the tabs on
the bulb-socket with the slots in
the assembly. Push the bulb-sock‐
et into the headlamp assembly and
turn the socket clockwise.
Static bending light replacement
(Headlamp Type B)
0:##
1. Open the hood.
2. Remove the headlamp bulb cover by turning it counterclockwise.
Maintenance
8-112

3. Remove the bulb-socket from theheadlamp assembly by turning the
bulb-socket counterclockwise until
the tabs on the bulb-socket align
with the slots on the headlamp as‐
sembly.
4. Remove the bulb from bulb-socket by pulling it out.
5. Insert a new bulb by inserting it in‐ to the bulb-socket.
6. Install the bulb-socket in the head‐ lamp assembly by aligning the tabs
on the bulb-socket with the slots in
the headlamp assembly. Push the
bulb-socket into the headlamp as‐
sembly and turn the bulb-socket
clockwise.
7. Install the headlamp bulb cover by turning it clockwise.Position lamp / Day time
running lamp (LED type)
replacement (Headlamp Type B)
0:##
If the position lamp + DRL (LED) (1)
does not operate, have your vehicle checked by a professional workshop.
Kia recommends to visit an authorized
Kia dealer/service partner.
The LED lamps cannot be replaced as a
single unit because it is an integrated unit. The LED lamps has to be replaced
with the unit.
A skilled technician should check or re‐
pair the position lamp + DRL (LED), for it may damage related parts of the ve‐
hicle.
Front fog lamp bulb
replacement
0:##
If the front fog lamp (1) does not oper‐
ate, have your vehicle checked by a professional workshop. Kia recom‐
mends to visit an authorized Kia dealer/
service partner.

8-113
8
Maintenance

Rear turn signal lamp bulb
replacement
0:##
1. Open the tail gate.
2. Loosen the light assembly retainingscrews with a cross-tip screwdriv‐
er.
0:##
3. Remove the rear combination lamp assembly from the body of the ve‐
hicle.
4. Disconnect the rear combination lamp connector.
0:##
5. Remove the socket from the as‐sembly by turning the socket coun‐
terclockwise until the tabs on the
socket align with the slots on the
assembly.
6. Remove the bulb from the socket by pressing it in and rotating it
counterclockwise until the tabs on
the bulb align with the slots in the socket. Pull the bulb out of the
socket.
7. Insert a new bulb by inserting it in‐ to the socket and rotating it until it
locks into place.
8. Install the socket in the assembly by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
9. Install the rear combination lamp assembly to the body of the vehi‐
cle.
Maintenance
8-114

Stop and tail lamp bulb
replacement
0:##
1. Open the tail gate.
2. Loosen the light assembly retainingscrews with a cross-tip screwdriv‐
er.
0:##
3. Remove the rear combination lamp assembly from the body of the ve‐
hicle.
4. Disconnect the rear combination lamp connector.
0:##
5. Remove the socket from the as‐sembly by turning the socket coun‐
terclockwise until the tabs on the
socket align with the slots on the
assembly.
6. Remove the bulb from the socket by pressing it in and rotating it
counterclockwise until the tabs on
the bulb align with the slots in the socket. Pull the bulb out of the
socket.
7. Insert a new bulb by inserting it in‐ to the socket and rotating it until it
locks into place.
8. Install the socket in the assembly by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
9. Install the rear combination lamp assembly to the body of the vehi‐
cle.

8-115
8
Maintenance