2018 INFINITI QX60 check transmission fluid

Shift lock release
If the battery charge is low or discharged, the
shift lever may not be moved from the P
(Park) position even with the brake pedal de-
pressed and the shift lever button pressed. To
move the shift lever, perform the following
procedure:1. Push the ignition switch to the OFF or LOCK position.
2. Apply the parking brake.
3. Remove the shift lock release cover us- ing a suitable tool. 4. Push down the shift lock release using a
suitable tool.
5. Press the shift lever button and move the shift lever to the N (Neutral) position
while holding down the shift lock release.
The vehicle may be moved to the desired
location. Replace the removed shift lock
release cover after the operation.
If the shift lever cannot be moved out of the P
(Park) position, have the Continuously Vari-
able Transmission system checked as soon as
possible. It is recommended that you visit an
INFINITI retailer for this service.
WARNING
If the shift lever cannot be moved from the
P (Park) position while the engine is running
and the brake pedal is depressed, the stop
lights may not work. Malfunctioning stop
lights could cause an accident injuring your-
self and others.
Accelerator downshift
— in D (Drive) position —
For passing or hill climbing, depress the ac-
celerator pedal to the floor. This shifts the
transmission down into a lower gear, de-
pending on the vehicle speed.
High fluid temperature protection
mode
This transmission has a high fluid tempera-
ture protection mode. If the fluid temperature
becomes too high (for example, when climb-
ing steep grades in high temperatures with
heavy loads, such as when towing a trailer),
engine power and, under some conditions,
vehicle speed will be decreased automatically
to reduce the chance of transmission dam-
age. Vehicle speed can be controlled with the
accelerator pedal, but the engine and vehicle
speed may be limited.
Fail-safe
If the vehicle is driven under extreme condi-
tions, such as excessive wheel spinning and
subsequent hard braking, the fail-safe sys-
tem may be activated. The Malfunction Indi-
cator Light (MIL) may illuminate to indicate
the fail-safe mode is activated. For addi-
tional information, refer to “Malfunction In-
dicator Light (MIL)” in the “Instrument and
controls” section of this manual. This will oc-
cur even if all electrical circuits are function-
ing properly. In this case, place the ignition
switch in the OFF position and wait for
10 seconds. Then turn the switch back to the
ON position. The vehicle should return to its
normal operating condition. If it does not re-
LSD2360
5-22Starting and driving

turn to its normal operating condition, have
the transmission checked and repaired, if
necessary. It is recommended that you visit
an INFINITI retailer for this service.
WARNING
When the high fluid temperature protec-
tion mode or fail-safe operation occurs, ve-
hicle speed may be gradually reduced. The
reduced speed may be lower than other
traffic, which could increase the chance of a
collision. Be especially careful when driving.
If necessary, pull to the side of the road at a
safe place and allow the transmission to re-
turn to normal operation, or have it re-
paired if necessary.
WARNING
∙ Be sure the parking brake is fully releasedbefore driving. Failure to do so can cause
brake failure and lead to an accident.
∙ Do not release the parking brake from outside the vehicle.
∙ Do not use the shift lever in place of the parking brake. When parking, be sure the
parking brake is fully engaged.
∙ To help avoid risk of injury or death through unintended operation of the ve-
hicle and/or its systems, do not leave
children, people who require the assis-
tance of others or pets unattended in
your vehicle. Additionally, the tempera-
ture inside a closed vehicle on a warm day
can quickly become high enough to cause
a significant risk of injury or death to
people and pets. To engage:
Firmly depress the parking brake.
To release: 1. Firmly apply the foot brake.
2. Move the shift lever to the P (Park) po- sition.
3. Firmly depress the parking brake pedal and it will release.
4. Before driving, be sure the brake warn- ing light goes out.
LSD0158
PARKING BRAKE
Starting and driving5-23

8 Maintenance and do-it-yourself
Maintenance requirements.......................8-2
General maintenance .............................8-2
Explanation of general maintenance
items .........................................8-2
Maintenance precautions .........................8-5
Engine compartment check locations ..............8-6
Engine cooling system ........................... 8-8
Checking engine coolant level ................. 8-8
Changing engine coolant ......................8-9
Engine oil ........................................8-9
Checking engine oil level .......................8-9
Changing engine oil ......................... 8-10
Changing engine oil filter ....................8-12
Continuously Variable Transmission (CVT) fluid . . 8-13
Power steering fluid ............................ 8-13
Brake fluid ..................................... 8-14
Windshield-washer fluid ........................ 8-14
Windshield-washer fluid reservoir ............8-14
Battery ........................................ 8-16
Jump starting ............................... 8-18
Drive belt ...................................... 8-18
Spark plugs .................................... 8-19
Replacing spark plugs ....................... 8-19Air cleaner
..................................... 8-20
Air conditioner filter ......................... 8-20
Windshield wiper blades ........................ 8-21
Cleaning .................................... 8-21
Replacing ................................... 8-21
Parking brake and brake pedal ..................8-22
Checking parking brake ......................8-22
Checking brake pedal ........................ 8-23
Brake booster ............................... 8-23
Fuses .......................................... 8-24
Engine compartment ........................ 8-24
Passenger compartment .....................8-25
Battery replacement ............................ 8-25
INFINITI Intelligent Key ......................8-26
Lights ......................................... 8-28
Headlights .................................. 8-28
Fog

lights ................................... 8-28
Exterior and interior lights ...................8-29
Wheels and tires ............................... 8-31
Tire pressure ................................ 8-31
Types of tires ............................... 8-34
Tire chains .................................. 8-35
Changing wheels and tires ...................8-35

vehicle is held securely on a fairly steep hill
when only the parking brake is applied.
Seat beltsCheck that all parts of the seat belt
system (for example, buckles, anchors, ad-
justers and retractors) operate properly and
smoothly, and are installed securely. Check
the belt webbing for cuts, fraying, wear or
damage.
Steering wheel Check for changes in the
steering condition, such as excessive play,
hard steering or strange noises.
Warning lights and chimes Make sure that all
warning lights and chimes are operating
properly.
Windshield defogger Check that the air
comes out of the defogger outlets properly
and in good quantity when operating the
heater or air conditioner.
Windshield wiper and washer* Check that
the wipers and washer operate properly and
that the wipers do not streak.
Under the hood and vehicle
The maintenance items listed here should be
checked periodically (for example, each time
you check the engine oil or refuel). Battery* (except for maintenance free bat-
teries)
Check the fluid level in each cell. The
fluid should be at the bottom of the filler
opening. Vehicles operated in high tempera-
tures or under severe conditions require fre-
quent checks of the battery fluid level.
NOTE:
Care should be taken to avoid situations
that can lead to potential battery discharge
and potential no-start conditions such as:
1. Installation or extended use of elec-
tronic accessories that consume battery
power when the engine is not running
(Phone chargers, GPS, DVD players,
etc.).
2. Vehicle is not driven regularly and/or
only driven short distances.
In these cases, the battery may need to be
charged to maintain battery health.
Brake (and clutch) fluid level(s)* For Manual
Transmission (M/T) model; make sure that
the brake and clutch fluid levels are between
the MAX and MIN lines on the reservoirs.
Except for Manual Transmission (M/T)
model; make sure that the brake fluid level is
between the MAX and MIN lines on the res-
ervoir. Engine coolant level*
Check the coolant level
when the engine is cold. Make sure that the
coolant level is between the MAX and MIN
lines on the reservoir.
Engine drive belt(s)* Make sure the drive
belt(s) is not frayed, worn, cracked or oily.
Engine oil level* Check the level after parking
the vehicle (on level ground) and turning off
the engine.
Fluid leaks Check under the vehicle for fuel,
oil, water or other fluid leaks after the vehicle
has been parked for a while. Water dripping
from the air conditioner after use is normal. If
you should notice any leaks or if fuel fumes
are evident, check for the cause and have it
corrected immediately.
Power steering fluid level* and lines Check
the level when the fluid is cold with the engine
off. Check the lines for proper attachment,
leaks, cracks, etc.
Windshield-washer fluid* Check that there is
adequate fluid in the reservoir.
8-4Maintenance and do-it-yourself

WARNING
∙ Never remove the radiator or coolantreservoir cap when the engine is hot.
Wait until the engine and radiator cool
down. Serious burns could be caused by
high pressure fluid escaping from the ra-
diator. Wait until the engine and radiator
cool down.
∙ Engine coolant is poisonous and should be stored carefully in marked containers
out of the reach of children.
∙ If the engine was stopped soon when the engine is still hot, the cooling fan may
operate for approximately one minute
after the engine was stopped to cool the
components in the engine compartment.
While the cooling fan is operating, be
sure that hands and other items do not
get caught in it.
The engine cooling system is filled at the
factory with a high-quality, year-round, anti-
freeze coolant solution. The antifreeze solu-
tion contains rust and corrosion inhibitors,
therefore additional engine cooling system
additives are not necessary.
CAUTION
∙ Never use any cooling system additives such as radiator sealer. Additives may
clog the cooling system and cause dam-
age to the engine, transmission and/or
cooling system.
∙ When adding or replacing coolant, be sure to use only Genuine NISSAN Engine
Coolant or equivalent in its quality with
the proper mixture ratio. Examples of the
mixture ratio of coolant and water are
shown below:
Outside
tempera- ture
down to Engine coolant
(concentrated) Demineralized
or distilled water
°C °F
-15 5 30% 70%
-35 -30 50% 50%
The radiator is equipped with a pressure cap.
To prevent engine damage, use only a Genu-
ine NISSAN radiator cap or its equivalent
when replacement is required.
CHECKING ENGINE COOLANT
LEVEL
Check the coolant level in the reservoir when
the engine is cold. If the coolant level is below
the MIN level
1, add coolant to the MAX
level
2. If the reservoir is empty, check the
coolant level in the radiator when the engine
is cold. If there is insufficient coolant in the
radiator, fill the radiator with coolant up to
the filler opening and also add it to the reser-
voir up to the MAX level
2.
The engine coolant reservoir is a pressurized
tank. When installing the cap, tighten it until
a clicking sound is heard.
LDI2519
ENGINE COOLING SYSTEM
8-8Maintenance and do-it-yourself

CAUTION
∙ Use only Genuine NISSAN CVT FluidNS-3. Do not mix with other fluids.
∙ Using transmission fluid other than Genuine NISSAN CVT Fluid NS-3 will
damage the CVT, which is not covered by
the warranty.
When checking or replacement of CVT fluid is
required, we recommend an INFINITI retailer
for servicing.
Check the fluid level in the reservoir.
The fluid level should be checked when the
fluid is cold at fluid temperatures of 0 to
30ºC (32 to 86ºF). The fluid level can be
checked with the level gauge which is at-
tached to the cap. To check the fluid level,
remove the cap. The fluid level should be
between the MAX
Aand MINBlines.
If the fluid is below the MIN
Bline, add
Genuine NISSAN E-PSF or equivalent. Re-
move the cap and fill through the opening.
WARNING
Power steering fluid is poisonous and
should be stored carefully in marked con-
tainers out of the reach of children.
CAUTION
∙ DO NOT OVERFILL.
∙ Use of a power steering fluid other than Genuine NISSAN E-PSF or equivalent
will prevent the power steering system
from operating properly.
LDI2861
CONTINUOUSLY VARIABLE
TRANSMISSION (CVT) FLUID POWER STEERING FLUID
Maintenance and do-it-yourself8-13

Child safety rear door lock...........3-6
Chimes, audible reminders ..........2-15
Cigarettelighterandashtray ........2-54
Cleaning exterior and interior ......7-2,7-4
Climate control seat switch .........2-45
Cold weather driving .............5-151
Console box ..................2-58
Continuously Variable Transmission
(CVT) ......................5-18
Continuously Variable Transmission
(CVT) fluid .................8-13
Driving with Continuously Variable
Transmission (CVT) ............5-18
Controls Heater and air conditioner controls. . .4-34
Coolant Capacities and recommended
fuel/lubricants................9-2
Changing engine coolant ..........8-9
Checking engine coolant level .......8-8
Engine coolant temperature gauge ....2-6
Corrosion protection ..............7-6
Cruisecontrol..................5-76
Cupholders...................2-59
D
Daytime Running Light System .......2-43
Defogger Switch ................2-38
Dimensionsandweights............9-7
Dimmer switch for instrument panel ....2-44
Distance Control Assist (DCA) system . . .5-99
Doors .......................3-4
Drivebelt....................8-18
Drive positioner, Automatic .....3-37,3-39Driving
Cold weather driving ...........5-151
Driving with Continuously Variable
Transmission (CVT) ............5-18
Precautions when starting
and driving ..............5-4,5-10
Driving the vehicle ...............5-18
Dual panel moonroof .............2-67
Dual power moonroof .........2-67,2-67
E
Economy - fuel ................5-133
Emergency engine shutoff .......5-15,6-2
Engine Before starting the engine ........5-17
Capacities and recommended
fuel/lubricants................9-2
Changing engine coolant ..........8-9
Changing engine oil ............8-10
Changing engine oil filter .........8-12
Checking engine coolant level .......8-8
Checking engine oil level ..........8-9
Engine compartment check locations . .8-6
Engine coolant temperature gauge ....2-6
Engine cooling system ...........8-8
Engine oil ...................8-9
Engine serial number ............9-9
Engine specifications ............9-6
Starting the engine ............5-17
Engine coolant temperature gauge ......2-6
Exhaust gas (Carbon monoxide) .......5-4
Explanation of maintenance items ......8-2
Extended storage switch ...........2-55 F
Flashers (See
hazard warning flasher switch) ........6-2
Flat tire ......................6-3
Floor mat positioning aid ............7-5
Fluid B
rakefluid .................8-14
Capacities and recommended
fuel/lubricants................9-2
Continuously Variable Transmission
(CVT) fluid .................8-13
Engine coolant ................8-8
Engine oil ...................8-9
Power steering fluid ............8-13
Windshield-washerfluid.........8-14
Fog light switch ................ 2-45
Forward Emergency Braking (FEB) with
Pedestrian Detection system ....2-10,5-112
Front air bag system (See
supplemental restraint system) .......1-54
Front and rear sonar system ........5-147
Front-door pocket ...............2-56
Front power seat adjustment .........1-3
Frontseats....................1-2
Fuel Capacities and recommended
fuel/lubricants................9-2
Fuel economy ............... 5-133
Fuel-filler door and cap ..........3-30
Fuel gauge ..................2-7
Loose fuel cap warning ..........2-28
Fuel-filler door .................3-29
Fuel gauge ....................2-7
Fuses ......................8-24
10-2