2018 INFINITI QX30 maintenance

4. Fit the replacement battery in the vehicle.
REINITIALISATION PROCEDURE
AFTER BATTERY
RECONNECTION
If the battery has been reconnected, check
the following items:
•Clock setting (if so equipped). For details,
see "Clock" in the "2. Instruments and con-
trols" section, or the separately provided
navigation system Owner's Manual, or the
audio device descriptions in " Audio system
(if equipped)" in the "4. Display screen,
heater and air conditioner, and audio sys-
tem" section.
•Reset the desired radio stations to the pre-
set station buttons. For details, see the
audio device descriptions in the “4. Heater
and air conditioner, and audio system”.
JUMP-STARTING
If jump-starting is necessary, see "Jump
starting" in the "6. In case of emergency" sec-
tion. If the engine does not start by jump
starting, the battery may have to be replaced.
It is recommended that you visit an INFINITI
retailer for this service.
WARNING
Be sure the ignition switch is in the OFF
position before servicing drive belt. The en-
gine could rotate unexpectedly.
1. Visually inspect each belt for signs of un- usual wear, cuts, fraying or looseness. If
the belt is in poor condition or loose, have
it replaced or adjusted. It is recommended
that you visit an INFINITI retailer for this
service.
2. Have the belts checked regularly for con- dition and tension in accordance with the
maintenance schedule as shown in a
separately provided Warranty Informa-
tion and Maintenance booklet.
NDI1635
DRIVE BELT
8-12Do-it-yourself

Replace the spark plugs according to the
maintenance schedule shown in a separate
maintenance booklet.
If replacement is required, it is recommended
that you visit an INFINITI retailer.
Always replace spark plugs with recom-
mended or equivalent ones.
WARNING
Be sure the engine and ignition switch are
off and that the parking brake is engaged
securely.
CAUTION
•Be sure to use the correct socket to re-
move the spark plugs. An incorrect
socket can cause damage to the spark
plugs. It is recommended that you visit an INFINITI
retailer if checking or replacement is required.
WARNING
•Operating the engine with the air
cleaner filter off can cause you or others
to be burned. The air cleaner filter not
only cleans the intake air, it also stops
the flame if the engine backfires. If the
air cleaner is not installed and the engine
backfires, you could be burned. Never
drive with the air cleaner filter off. Be
cautious working on the engine when
the air cleaner is off.
•Never pour fuel into the throttle body or
attempt to start the engine with the air
cleaner removed. Doing so could result
in serious injury.
CLEANING
If the windshield or rear window is not clear
after using the window washer or if a wiper
blade chatters when running, wax or other
material may be on the blade or windshield.
Clean the outside of the windshield or rear
window with a washer solution or a mild
detergent. The windshield or rear window is
clean if beads do not form when rinsing with
clear water.
Clean the blade by wiping it with a cloth
soaked in a washer solution or a mild deter-
gent. Then rinse the blade with clear water. If
the windshield or rear window is still not clear
after cleaning the blades and using the wiper,
replace the blades.
CAUTION
Worn windshield wiper blades can damage
the windshield and impair driver vision.
SPARK PLUGS AIR CLEANER FILTERWIPER BLADES
Do-it-yourself8-13

TIRE ROTATION
INFINITI recommends rotating the tires ev-
ery 5,000 miles (8,000 km).
For additional information on tire replacing
procedures, refer to "Flat tire" in the "6. In
case of emergency" section.As soon as pos-
sible, tighten the wheel nuts to the specified
torque with a torque wrench.
Wheel nut tightening torque: 96 ft-lb (130
N·m)
The wheel nuts must be kept tightened to
specifications at all times. It is recommended
that wheel nuts be tightened to specification
at each tire rotation interval.
WARNING
•After rotating the tires, check and ad-
just the tire pressure.
•Do not include the spare tire in the tire
rotation.
•For additional information regarding
tires, refer to "Important Tire Safety In-
formation" (US) or "Tire Safety Infor-
mation" in the Warranty Information
Booklet.
REPLACING WHEELS AND TIRES
WARNING
Do not install a deformed wheel or tire even
if it has been repaired. Such wheels or tires
could have structural damage and could
fail without warning.
When replacing a tire, use the same size,
speed rating and load carrying capacity as
originally equipped. (See "Wheels and Tires" in
the "9. Maintenance and Schedules" section
for recommended types and sizes of tires and
wheels.)
If the wheels are changed for any reason,
always replace with wheels which have the
same offset dimension. Wheels of a different
offset could cause early tire wear, possibly
degraded vehicle handling characteristics
and/or interference with the brake discs/
drums. Such interference can lead to de-
creased braking efficiency and/or early brake
pad/shoe wear.
Confirm the following for the TPMS:
WARNING
•The use of tires other than those recom-
mended or the mixed use of tires of dif-
ferent brands, construction (bias, bias-
belted or radial), or tread patterns can
adversely affect the ride, braking, han-
dling, VDC system, ground clearance,
body-to-tire clearance, tire chain clear-
ance, speedometer calibration, head-
light aim and bumper height. Some of
these effects may lead to accidents and
could result in serious personal injury.
•For 2WD models, if your vehicle was
originally equipped with 4 tires that
were the same size and you are only re-
placing 2 of the 4 tires, install the new
tires on the rear axle. Placing new tires
on the front axle may cause loss of ve-
hicle control in some driving conditions
and cause an accident and personal in-
jury.
•If the wheels are changed for any rea-
son, always replace with wheels which
have the same offset dimension. Wheels
of a different offset could cause prema-
ture tire wear, degrade vehicle handling
characteristics, affect the VDC system
and/or interference with the brake
discs. Such interference can lead to de-
creased braking efficiency and/or early
8-34Do-it-yourself

9 Maintenance and Schedules
Maintenance requirements................9-2
General maintenance ................. .9-2
Scheduled maintenance ................9-2
Where to go for service ................9-2
General maintenance ................... .9-2
Explanation of general maintenance items . . . .9-2
Explanation of general maintenance items ......9-5
Emission control system maintenance .......9-6
Chassis and body maintenance ...........9-6
Maintenance schedules ................. .9-7Additional maintenance items for severe
operating systems
.................. .9-7
Oil change monitor .................. .9-7
Maintenance service messages ...........9-7
Standard maintenance ................. .9-10
Emission control system maintenance
(For 2.0L turbo gasoline engine) .........9-10
Chassis & body maintenance ............9-13
Maintenance log ..................... .9-15

Some day-to-day and regular maintenance is
essential to maintain your vehicle’s good me-
chanical condition, as well as its emission and
engine performance.
It is the owner’s responsibility to make sure
that the specified maintenance, as well as
general maintenance, is performed.
As the vehicle owner, you are the only one
who can ensure that your vehicle receives the
proper maintenance care. You are a vital link
in the maintenance chain.
GENERAL MAINTENANCE
General maintenance includes those items
which should be checked during normal day-
to-day operation of the vehicle. They are es-
sential if your vehicle is to continue to operate
properly. It is your responsibility to perform
these procedures regularly as prescribed.
Performing general maintenance checks re-
quires minimal mechanical skill and only a few
general automotive tools.
These checks and inspections can be done by
yourself, a qualified technician, or if you pre-
fer, an INFINITI retailer.
SCHEDULED MAINTENANCE
The maintenance items listed under "Mainte-
nance schedules" later in this section are re-
quired to be serviced at regular intervals.
However under severe driving conditions, ad-
ditional or more frequent maintenance will be
required.
WHERE TO GO FOR SERVICE
If maintenance service is required or your
vehicle appears to malfunction, have the sys-
tems checked and serviced. It is recom-
mended you visit an INFINITI retailer for this
service.
INFINITI technicians are well-trained spe-
cialists and are kept up to date with the latest
service information through technical bulle-
tins, service tips and training programs. They
are completely qualified to work on INFINITI
vehiclesbeforework begins.
You can be confident that an INFINITI retail-
er’s service department can perform the ser-
vice needed to meet the maintenance re-
quirements on your vehicle. During normal day-to-day operation of the
vehicle, general maintenance should be per-
formed regularly as prescribed in this section.
If you detect any unusual sounds, vibrations
or smells, be sure to check for the cause or
have an INFINITI retailer do it promptly. In
addition, it is recommended you notify an
INFINITI retailer if you think that repairs are
required.
When performing any checks or maintenance
work, closely observe "Explanation of general
maintenance items" later in this section.
EXPLANATION OF GENERAL
MAINTENANCE ITEMS
Additional information on the following
items with “*” is found later in the “Do-it-
yourself” section of this manual.
Outside the vehicle
The maintenance items listed here should be
performed from time to time, unless other-
wise specified.
Doors and engine hood:
Check that all doors, the lift gate and the
engine hood operate smoothly. Also make
sure that all latches lock securely. Lubricate if
necessary. Make sure that the secondary
latch keeps the hood from opening when the
MAINTENANCE REQUIREMENTS
GENERAL MAINTENANCE
9-2Maintenance and Schedules

primary latch is released. When driving in ar-
eas using road salt or other corrosive materi-
als, check lubrication frequently.
Lights*:
Clean the headlights on a regular basis. Make
sure that the headlights, stop lights, tail lights,
turn signal lights, and other lights are all op-
erating properly and installed securely. Also
check the aim of the headlights.
Road wheel nuts (lug nuts)*:
When checking the tires, make sure no wheel
nuts are missing, and check for any loose
wheel nuts. Tighten if necessary.
Tire rotation*:
Tires should be rotated every 5,000 miles
(8,000 km). Tires marked with directional
indicators can only be rotated between front
and rear. Make sure that the directional indi-
cators point in the direction of wheel rotation
after the tire rotation is completed.
Tires*:
Check the pressure with a gauge often and
always prior to long distance trips. Adjust the
pressure in all tires to the pressure specified.
Check carefully for damage, cuts or excessive
wear.Tire Pressure Monitoring System (TPMS)
transmitter components:
Replace the TPMS transmitter grommet seal,
valve core and cap when the tires are re-
placed due to wear or age.
Wheel alignment and balance:
If the vehicle should pull to either side while
driving on a straight and level road, or if you
detect uneven or abnormal tire wear, there
may be a need for wheel alignment.
If the steering wheel or seat vibrates at nor-
mal highway speeds, wheel balancing may be
needed.
For additional information regarding tires, re-
fer to “Important Tire Safety Information”
(US) or “Tire Safety Information” (Canada) in
the INFINITI Warranty Information Booklet.
Windshield:
Clean the windshield on a regular basis.
Check the windshield at least every six
months for cracks or other damage. Have a
damaged windshield repaired by a qualified
repair facility.
Wiper blades*:
Check for cracks or wear if not functioning
correctly. Replace as necessary.Inside the vehicle
The maintenance items listed here should be
checked on a regular basis, such as when
performing scheduled maintenance, cleaning
the vehicle, etc.
Accelerator pedal:
Check the pedal for smooth operation and
make sure that the pedal does not catch or
require uneven effort. Keep the floor mat
away from the pedal.
Automatic transmission P (Park) mecha-
nism:
On a fairly steep hill, check that your vehicle is
held securely when P (Park) has been acti-
vated, without applying any brakes.
Brake pedal*:
Check the pedal for smooth operation. If the
brake pedal suddenly goes down further than
normal, the pedal feels spongy or the vehicle
seems to take longer to stop, have your ve-
hicle checked immediately. It is recommended
you visit an INFINITI retailer for this service.
Keep the floor mat away from the pedal.
Brakes:
Check that the brakes do not pull the vehicle
to one side when applied.
Maintenance and Schedules9-3

Parking brake*:
Check the parking brake operation regularly.
Also make sure that the vehicle is held se-
curely on a fairly steep hill when only the
parking brake is applied. If the parking brake
needs adjustment, it is recommended you
visit an INFINITI retailer for this service.
Seats:
Check seat position controls such as seat
adjusters, seatback recliner, etc. to ensure
they operate smoothly and that all latches
lock securely in every position. Check that the
head restraints move up and down smoothly
and that the locks (if so equipped) hold se-
curely in all latched positions.
Seat belts:
Check that all parts of the seat belt system
(for example, buckles, anchors, adjusters and
retractors) operate properly and smoothly,
and are installed securely. Check the belt
webbing for cuts, fraying, wear or damage.
Steering wheel:
Check for changes in the steering condition,
such as excessive free play, hard steering or
strange noises.
Warning lights and chimes:
Make sure that all warning lights and chimes
are operating properly.Windshield defroster:
Check that the air comes out of the defroster
outlets properly and in good quantity when
operating the heater or air conditioner.
Windshield wiper and washer*:
Check that the wipers and washer operate
properly and that the wipers do not streak.
Under the hood and vehicle
The maintenance items listed here should be
checked periodically (for example, each time
you check the engine oil or refuel).
Battery*:
Except for maintenance free battery, check
the fluid level in each cell. It should be be-
tween the “UPPER” and “LOWER” lines. Ve-
hicles operated in high temperatures or under
severe conditions require frequent checks of
the battery fluid level.
NOTE
Care should be taken to avoid situations
that can lead to potential battery discharge
and potential no-start conditions such as:
1. Installation or extended use of electronic
accessories that consume battery power
when the engine is not running (Phone
chargers, GPS, DVD players, etc.) 2. Vehicle is not driven regularly and/or
only driven short distances.
In these cases, the battery may need to be
charged to maintain battery health.
Brake fluid level*:
Make sure that the brake fluid level is be-
tween the “MAX” and “MIN” lines on the res-
ervoir.
Coolant level*:
Check the coolant level when the engine is
cold.
Engine drive belt(s)*:
Make sure that no belt is frayed, worn,
cracked or oily.
Engine oil level*:
Check the level after parking the vehicle on a
level spot and turning off the engine. Wait
more than 15 minutes for the oil to drain back
into the oil pan.
Exhaust system:
Make sure there are no loose supports,
cracks or holes. If the sound of the exhaust
seems unusual or there is a smell of exhaust
fumes, immediately have the exhaust system
inspected. It is recommended you visit an
9-4Maintenance and Schedules

INFINITI retailer for this service. See "Precau-
tions when starting and driving" in the "5.
Starting and driving" section.
Fluid leaks:
Check under the vehicle for fuel, oil, water or
other fluid leaks after the vehicle has been
parked for a while. Water dripping from the
air conditioner after use is normal. If you
should notice any leaks or if gasoline fumes
are evident, check for the cause and have it
corrected immediately.
Radiator and hoses:
Check the front of the radiator and clean off
any dirt, insects, leaves, etc., that may have
accumulated. Make sure the hoses have no
cracks, deformation, rot or loose connec-
tions.Underbody:
The underbody is frequently exposed to cor-
rosive substances such as those used on icy
roads or to control dust. It is very important to
remove these substances, otherwise rust will
form on the floor pan, frame, fuel lines and
around the exhaust system. At the end of
winter, the underbody should be thoroughly
flushed with plain water, being careful to
clean those areas where mud and dirt may
accumulate. For additional information, see
"Cleaning exterior" in the "7. Appearance and
care" section.
Windshield washer fluid*:
Check that there is adequate fluid in the res-
ervoir.
The following descriptions are provided to
give you a better understanding of the sched-
uled maintenance items that should be regu-
larly checked or replaced. The maintenance
schedule indicates at which mileage/time in-
tervals each item requires service.
In addition to scheduled maintenance, your
vehicle requires that some items be checked
during normal day-to-day operation. Refer to
"General maintenance" in this section.
Items marked with “*” are recommended by
INFINITI for reliable vehicle operation. You
are not required to perform maintenance on
these items in order to maintain the warran-
ties which come with your vehicle. Other
maintenance items and intervals are required.
When applicable, additional information can
be found in the “Do-it-yourself” section in
Chapter 8.
NOTE
INFINITI does not advocate the use of non-
OEM approved aftermarket flushing sys-
tems and strongly advises against perform-
ing these services on an INFINITI product.
Many of the aftermarket flushing systems
use non-OEM approved chemicals or sol-
vents, the use of which has not been vali-
dated by INFINITI.
EXPLANATION OF GENERAL
MAINTENANCE ITEMS
Maintenance and Schedules9-5