6. To lift the vehicle, securely hold and turnthe ratchet handle
1clockwise as shown.
7. Carefully raise the vehicle until the tire clears the ground.
8. Remove the wheel bolts, then remove the wheel with the flat tire.
WARNING
The wheel is heavy. Be sure that your feet
are clear of the wheel and use gloves as
necessary to avoid injury.
Installing the wheel
WARNING
•A temporary use spare wheel and tire is
designed for emergency use.
•Never use wheel bolts other than those
provided with your vehicle. Incorrect
wheel bolts or improperly tightened
wheel bolts may cause the wheel to be-
come loose or come off. This could cause
an accident.
•Never use oil or grease on the wheel
bolts. This may cause the wheel bolts to
become loose.
ATighten
BLoosen
1. Clean any mud or dirt from the surface between the wheel and the hub.
2. Carefully fit the wheel and tighten the wheel bolts with your fingers. Check that
all the wheel bolts contact the wheel sur-
face horizontally and on the bevelled side.
Models with wheel lock bolt (if equipped):
Insert the wheel lock key into the wheel
lock bolt and tighten into the wheel finger
tight.
3. With the wheel wrench, tighten the wheel bolts alternately and evenly in the se-
quence as illustrated (
1-5) until they
are tight.
NCE449NCE435
6-8In case of emergency
4. Lower the vehicle slowly until the tiretouches the ground.
5. Tighten the wheel bolts securely using the wheel wrench in the sequence as illus-
trated.
6. Lower the vehicle completely.
7. Install the wheel cover (if equipped).
Wheel bolt tightening torque: 96 ft-lb (130 N•m, 13 kg-m)
As soon as possible, tighten the wheel bolts
to the specified torque with a torque wrench.
The wheel bolts must be kept tightened to
specification at all times. It is recommended
that the wheel bolts be tightened to specifi-
cation at each maintenance interval.
Adjust the tire pressure to the COLD pres-
sure.
COLD pressure is the tire pressure as mea-
sured after the vehicle has been parked for
three hours or more or driven for less than 1
mile (1.6 km).
COLD tire pressures are shown on the tire
and loading information label affixed to the
driver's side center pillar.
Wheel lock bolts (if equipped)
In order to prevent theft, the specially de-
signed wheel lock bolt is installed to each
wheel. The wheel lock bolt cannot be re-
moved with the commonly used tools.
When removing tires, use the lock key pro-
vided with your vehicle.
Removing the wheel lock bolt:
1. Insert the wheel lock key
1to the wheel
lock bolt.
2. To remove the wheel lock bolt, turn the wheel lock key counterclockwise using the
wheel wrench.
CAUTION
•Do not use a power tool to remove the
wheel lock bolts.
•When installing the wheel, tighten the
wheel lock bolts to the same tightening
torque as the normal wheel bolts. For
details, see "Installing the wheel" earlier
in this section.
NCE143Z
In case of emergency6-9
•When adding or replacing coolant, be
sure to use only INFINITI Genuine En-
gine Coolant, BASF Glysantin G40 or
equivalent in its quality. The use of other
types of engine coolant may damage the
engine cooling system.
CHECKING ENGINE COOLANT
LEVEL
NOTE
The coolant level must only be checked and
corrected when the engine is cold.
1. Park the vehicle on a level surface.
Only check the coolant level if the vehicle
is on a level surface and the engine is cold. 2. Slowly turn cap
1half a turn counter-
clockwise to allow excess pressure to es-
cape.
3. Turn cap
1further counter-clockwise
and remove it.
If the coolant is at the level of marker bar
3in the filler neck when cold, there is
enough coolant in coolant expansion tank
2.
4. If necessary, top up with INFINITI Genu- ine Engine Coolant, BASF Glysantin G40
or equivalent in its quality.
5. Replace cap
1and turn it clockwise as
far as it will go.
If the cooling system frequently requires
coolant, have it checked. It is recommended
that you visit an INFINITI retailer for this
service.
CHANGING ENGINE COOLANT
An INFINITI retailer can change the engine
coolant.
Improper servicing can result in reduced
heater performance and engine overheating.
WARNING
•To avoid being scalded, never change
the coolant when the engine is hot.
•Never remove the radiator cap when the
engine is hot. Serious burns could be
caused by high pressure fluid escaping
from the radiator.
•Avoid direct skin contact with used
coolant. If skin contact is made, wash
thoroughly with soap or hand cleaner as
soon as possible.
•Keep coolant out of reach of children
and pets.
Engine coolant must be disposed of properly.
Check your local regulations.
NDI1602
8-4Do-it-yourself
1. Park the vehicle on a level surface andapply the parking brake.
2. Start the engine and let it idle until it reaches the normal operating tempera-
ture, then turn it off.
3. Remove the oil filler cap by turning it counterclockwise.
4. Remove the engine undershield.
5. Place a large drain pan under the drain plug.
6. Remove the drain plug with a wrench by turning it counterclockwise and com-
pletely drain the oil. If the oil filter is to be
changed, remove and replace it at this
time. For additional information, refer to
"Changing engine oil filter" later in this
section.
•Waste oil must be disposed of prop-
erly.
•Check your local regulations.
7. Clean and reinstall the drain plug and a new washer. Securely tighten the drain
plug with a wrench. Do not use excessive
force.
Drain plug tightening torque: 22 ft-lb, 30
N•m
8. Refill engine with recommended oil through the oil filler opening, then install
the oil filler cap securely.
For additional information on drain and
refill capacity, refer to "Recommended
fluids/lubricants and capacities" in the "9.
Maintenance and Schedules" section.
The drain and refill capacity depends on
the oil temperature and drain time. Use
these specifications for reference only.
Always use the dipstick to determine
when the proper amount of oil is in the
engine.
9. Start the engine. Check for leakage around the drain plug and oil filter. Correct
as required.
10. Turn the engine off and wait more than 10 minutes. Check the oil level with the
dipstick. Add engine oil if necessary.
CHANGING ENGINE OIL FILTER
1. Park the vehicle on a level surface andapply the parking brake.
2. Turn the engine off.
3. Place a large drain pan under the oil filter
1.
4. Loosen the oil filter
1with an oil filter
wrench by turning it counterclockwise.
Then remove the oil filter by turning it by
hand.
CAUTION
Be careful not to burn yourself. The engine
oil may be hot.
5. Wipe the engine oil filter sealing surface with a clean rag.
NDI1622NDI1610
2.0L gasoline engine
8-6Do-it-yourself
4. Fit the replacement battery in the vehicle.
REINITIALISATION PROCEDURE
AFTER BATTERY
RECONNECTION
If the battery has been reconnected, check
the following items:
•Clock setting (if so equipped). For details,
see "Clock" in the "2. Instruments and con-
trols" section, or the separately provided
navigation system Owner's Manual, or the
audio device descriptions in " Audio system
(if equipped)" in the "4. Display screen,
heater and air conditioner, and audio sys-
tem" section.
•Reset the desired radio stations to the pre-
set station buttons. For details, see the
audio device descriptions in the “4. Heater
and air conditioner, and audio system”.
JUMP-STARTING
If jump-starting is necessary, see "Jump
starting" in the "6. In case of emergency" sec-
tion. If the engine does not start by jump
starting, the battery may have to be replaced.
It is recommended that you visit an INFINITI
retailer for this service.
WARNING
Be sure the ignition switch is in the OFF
position before servicing drive belt. The en-
gine could rotate unexpectedly.
1. Visually inspect each belt for signs of un- usual wear, cuts, fraying or looseness. If
the belt is in poor condition or loose, have
it replaced or adjusted. It is recommended
that you visit an INFINITI retailer for this
service.
2. Have the belts checked regularly for con- dition and tension in accordance with the
maintenance schedule as shown in a
separately provided Warranty Informa-
tion and Maintenance booklet.
NDI1635
DRIVE BELT
8-12Do-it-yourself
Halogen headlight bulb
Fitting/removing the access cover on the
front wheel arch:
You must remove the cover of the front
wheel arch before you can change the halo-
gen headlight bulb.
To remove: switch off the lights, turn the
steering so that the wheel behind the light in
question is pointing inwards . Slide cover
1up and remove it.To fit: inset cover
1again and slide it down
until it engages.
The headlight is a semi-sealed beam type
which uses a replaceable headlight (halogen)
bulb. A bulb can be replaced from inside the
engine compartment without removing the
headlight assembly.
If you need assistance for bulb replacement,
it is recommended that you visit an INFINITI
retailer.
Low/High beam Headlight bulb replace-
ment:
1. Open the hood. For details, see "Hood" inthe "3. Pre-driving checks and adjust-
ments" section.
2. Disconnect the negative (—) battery cable.
3. Remove the corresponding access cover from the wheel arch.
4. Turn housing cover
1counterclockwise
and remove it.
5. Turn bulb holder
2counterclockwise and
pull out
6. Take the headlight bulb out of bulb holder
2.
7. Insert the new bulb into bulb holder
2.
8. Insert bulb holder
2and turn it clockwise.
NDI1626NDI1611
Do-it-yourself8-25
9. Press on housing cover1and turn it to
the right.
10. Replace the cover in the front wheel arch
11. Reconnect the negative (—) battery cable and close the hood.
NOTE
Fog may temporarily form inside the lens of
the exterior lights in the rain or in a car wash.
The fog is caused by a temperature differ-
ence between the inside and the outside of
the lens. This is not a malfunction. If large
droplets can be seen, it is recommended that
you visit an INFINITI retailer.
Front turn signal light bulb
replacement (non-LED system only)
1. Open the hood. For details, see "Hood" in the "3. Pre-driving checks and adjust-
ments" section.
2. Disconnect the negative (—) battery cable.
3. Turn housing cover
1counterclockwise
and remove it.
4. Turn bulb holder
2counterclockwise and
pull out
5. Take the headlight bulb out of bulb holder
2. 6. Insert the new bulb into bulb holder
2.
7. Insert bulb holder
2and turn it clockwise.
8. Press on housing cover
1and turn it to
the right.
9. Reconnect the negative (—) battery cable and close the hood.
NDI1612
8-26Do-it-yourself
Checking.....................8-4
Coolant level .................8-4
Engine oil level ................8-5
Child restraints .................1-19
Anchorage ..................1-23
ISOFIX installation .............1-24
Precautions .................1-20
Childsafety...................1-17 Rear door locks ................3-7
Cleaning ......................7-3
Alloy wheels ..................7-3
Chromeparts.................7-3
Exterior ....................7-2
Glass......................7-3
Interior.....................7-4
Leatherseatcovers.............7-6
Removing spots ...............7-3
Seat belts ...................7-5
Underbody ..................7-3
Washing ....................7-2
Waxing .....................7-2
Clock.......................2-77 Adjusting time ................2-77
Coat hooks ...................2-81
Cockpit......................0-6 Overview ................0-6,2-2
Cold weather ..................5-97
Battery....................5-97
Drivingonsnoworice...........5-98
Engine coolant ...............5-97
Precautions .................5-97 Special equipment
.............5-98
Tire equipment ...............5-97
Compact Disc (CD) ..............4-71
Player ................4-71,4-127
Compartment .................2-87
Connecting ...................4-90
Bluetooth® device .............4-90
Bluetooth® Hands-Free Phone .....4-88
Coolant .....................10-2
Capacities ..................10-2
Changing engine coolant ..........8-4
Checking coolant level ...........8-4
Cold weather ................5-97
Engine cooling system ...........8-3
Temperature gauge .............2-6
Corrosionprotection..............7-7 Environmental factors ............7-7
Cruisecontrol .................5-46 Canceling ..................5-48
Operation ..................5-47
Cupholders ..................2-80
Customer assistance ............4-124
D
Defroster....................2-63
Switch ....................2-63
Dimensions...................10-9 Engine ....................10-7
Tires.....................10-8 Display .....................
2-70
Brightness.................. 2-70
Vehicle information display ........2-15
Warningsandindicators ......... 2-29
Doors .......................3-7
Liftgate....................3-7
Locking key ..................3-5
Locks .....................3-4
Map pocket ................. 2-83
Drive belts ....................8-12
Driving ......................5-20
Automatic Transmission .........5-20
Coldweather................5-97
Idle Stop/Start System ..........5-29
Onsnoworice...............5-98
Precautions..................5-4
E
Emergency key ..................3-2
Engine ......................5-18
Before starting ............... 5-18
Changing engine coolant ..........8-4
Changing engine oil .............8-5
Changing oil filter ..............8-6
Checking coolant level ...........8-4
Checking engine oil level ..........8-5
Coldweather................5-97
Compartment .............0-9,8-3
Coolingsystem................8-3
11-2Index