2018 INFINITI QX30 ECO mode

Setting the brightness of the ambient light-
ing:
1. Press the
orbutton on the
steering wheel to select the [Settings]
menu.
2. Press the
orbutton to select
[Light] submenu.
3. Press to confirm.
4. Press the
orbutton to select
the [Ambient Light Brightness] function.
You will see the selected setting.
5. Change the setting with . If you change the setting, conversion does
not take place until the next time the ve-
hicle is stationary.
6. Press the
orbutton to adjust
the brightness to a level from [Off] to
[Level 5] (bright).
7. Press the or
button to save the
setting. Activating/deactivating the surround
lighting and exterior lighting delayed
switch-off:
If you have activated the Surround lighting
function and the light switch is set to
, the following functions are acti-
vated when it is dark:
•Surround lighting: the exterior lighting re-
mains lit for 40 seconds after unlocking
with the key. If you start the engine, the
surround lighting is switched off and auto-
matic headlight mode is activated .
•Exterior lighting delayed switch-off: the
exterior lighting remains lit for 60 seconds
after the engine is switched off. If you
close all the doors and the lift gate, the
exterior lighting goes off after 15 seconds.
1. Press the
orbutton on the
steering wheel to select the [Settings]
menu.
2. Press the
orbutton to select
[Light] submenu.
3. Press to confirm.
4. Press the
orbutton to select
the [Surround Lighting] function.
5. Press the button to save the setting. When the [Surround Lighting] function is
activated, the light cone and the area around the vehicle are displayed in orange
in the vehicle information display
6. Press the button to confirm the set- ting.
Deactivating delayed switch-off of the exte-
rior lighting temporarily:
1. Before leaving the vehicle, switch the igni- tion switch to the OFF position.
2. Switch the ignition switch to the ON po- sition.
The exterior lighting delayed switch-off is
deactivated.
Delayed switch-off of the exterior lighting is
reactivated the next time you start the en-
gine.
Depending on your vehicle's equipment,
when the surround lighting and delayed
switch-off exterior lighting are on, the fol-
lowing light up:
•Side lights
•Fog lights
•Low beam headlights
•Daytime driving lights
•Surround lighting in the exterior mirrors
Instruments and controls2-27

Vehicle
MessagePossible causes/consequences and solutions
[Depress Brake to Start
Engine] (DCT models only). You have attempted to start the engine with the transmission in position N (Neutral) without depressing the
brake pedal.
Depress the brake pedal.
[To Deselect P or N,
Depress Brake and Start
Engine] You have attempted to shift the shift lever to position R (Reverse) or D (Drive) without starting the engine.
Start the engine and depress the brake pedal.
NOTE•It is only possible to move the shift lever from position P (Park) to the desired position if you depress the brake pedal. Only then
can the parking lock be deactivated.
•At transmission fluid temperatures below -5 °F (-20 °C) you can only shift out of position P (Park) into another transmission
position when the engine is running.
[Apply Brake to Shift From
'P'] You have attempted to shift the shift lever to position R (Reverse), N (Neutral) or D (Drive) without depressing the brake pedal.
Depress the brake pedal.
[Risk of Rolling Transmis-
sion Not in P] The driver's door is open/not fully closed and the shift lever is in position R (Reverse), N (Neutral) or D (Drive).
A warning tone also sounds
WARNING
The vehicle may roll away.
There is a risk of an accident.
1. Press the P (Park) button.
2. Secure the vehicle against rolling away.
3. Close the driver's door fully.
[Service Required Do Not
Shift Gears Visit Dealer] You cannot change the transmission position due to a malfunction.
A warning tone also sounds.
If transmission position D (Drive) is selected, Drive to an INFINITI retailer without shifting the transmission from position D (Drive).
If transmission position R (Reverse), N (Neutral) or P (Park), secure the vehicle against rolling away. It is recommended you consult
an INFINITI retailer.
2-54Instruments and controls

Key
ProblemPossible causes/consequences and solutions
[Key Does Not Belong to
Vehicle]You have put the wrong key in the ignition switch.
Use the correct key.
[Obtain a New Key]
The key needs to be replaced.
It is recommended you visit an INFINITI retailer for this service.
[Replace Key Battery]The key battery is discharged.
Replace the battery (see "Checking the battery" in the "8. Do-it-yourself" section)
[Key Not Detected] (red
display message)The key is not in the vehicle.
A warning tone also sounds.
If the engine is switched off, you can no longer lock the vehicle centrally or start the engine.
1. Pull over and stop the vehicle safely as soon as possible, paying attention to road and traffic conditions.
2. Secure the vehicle against rolling away.
3. Locate the key.
Because there is interference from a strong source of radio waves, the key is not detected whilst the engine is running.
A warning tone also sounds.
If the engine is switched off, you can no longer lock the vehicle centrally or start the engine.
1. Pull over and stop the vehicle safely as soon as possible, paying attention to road and traffic conditions.
2. Secure the vehicle against rolling away.
3. Insert the key into the ignition lock and bring into key mode.
[Remove 'Start' Button,
Then Insert Key]The key is continually undetected.
The key detection function has a temporary malfunction or is faulty. A warning tone also sounds.•Insert the key into the ignition lock and turn it to the desired position.•It is recommended you consult an INFINITI retailer.
[Key Not Detected] (white
display message)The key is currently undetected.
Change the location of the key in the vehicle.
If the key still cannot be detected, operate the vehicle with the key in the ignition switch if necessary.
2-58Instruments and controls

NOTE
The “Windshield demisting” function auto-
matically sets the blower output to the opti-
mum demisting effect. As a result, the air-
flow may increase or decrease automatically
after the
button is pressed
NOTE
You can adjust the blower output manually
while the “Windshield demisting” function is
in operation: by adjusting the airflow control
for the air-conditioning or climate control
system (see "Heater and air conditioner" in
the "4. Display screen, heater and air condi-
tioner, and audio system" section). To deactivate the de-icer:
•Press thebutton. The indicator light
in thebutton turns off. The previous
settings are reactivated. Air-recirculation
mode remains deactivated.
or
•Automatic climate control: press the
button. The indicator light in the
button turns off. Airflow and air dis-
tribution are set to automatic mode.
or
•Air-conditioning system or automatic cli-
mate control: adjust the temperature con-
trol (see "Heater and air conditioner" in the
"4. Display screen, heater and air condi-
tioner, and audio system" section).HEADLIGHT SWITCH
1Left-hand parking lights
2Right-hand parking lights
3Side lights and license plate light-
ing
4 Automatic headlight mode,
controlled by the light sensor
5Low beam/high beam headlights
6Rear fog light
7Front fog lights (if equipped)
8Headlight aiming control (halogen head-
lights only)
INFINITI recommends that you consult the
local regulations concerning the use of lights.
If you hear a warning tone when you leave
the vehicle, the side lights may still be
switched on. Turn the light switch to
.
NIC2619
LED headlights
HEADLIGHT AND TURN SIGNAL
SWITCHES
2-64Instruments and controls

ADAPTIVE FRONT LIGHTING
SYSTEM (LED HEADLIGHT
ONLY) (IF EQUIPPED)
The Adaptive Front Lighting System is a sys-
tem that adjusts the headlights automatically
to suit the prevailing driving and weather
conditions. It offers advanced functions for
improved illumination of the road surface,
e.g. depending on the vehicle speed or
weather conditions. The system includes the
active light function, cornering light function
and freeway mode. The system is only active
when it is dark.
You can activate or deactivate the “Adaptive
Front Lighting System” function using the
vehicle information display (see "Switching
the Adaptive Front Lighting System on/off"
earlier in this section)
Active light function
The active light function is a system that
moves the headlights according to the steer-
ing movements of the front wheels. In this
way relevant areas remain illuminated while
you are driving. This helps you to recognize
pedestrians, cyclists and animals. It is active
when the lights are switched on.
Cornering light function
The cornering light function improves the il-
lumination of the road over a wide angle in
the direction you are turning, enabling better
visibility in tight bends, for example. It can
only be activated when the low-beam head-
lights are switched on. It is active if you are
driving at speeds below 25 MPH (40 km/h)
and switch on the turn signal or turn the
steering wheel.
The cornering light function may remain lit for
a short time, but is automatically switched off
after no longer than three minutes.
NSD593NSD592
Instruments and controls2-67

Freeway mode
Freeway mode adjusts the light beam to re-
duce the amount of light that shines on the
opposite lane of the freeway, and oncoming
traffic.
Freeway mode is active if you are driving at a
speed above 68 MPH (110 km/h) and do not
make any large steering movements for at
least 3300 ft (1000 m) or if you are driving at
a speed above 81 MPH (130 km/h).
It is not active if you are driving at speeds
below 50 MPH (80 km/h) following activa-
tion.
HIGH BEAM ASSIST (LED
HEADLIGHT ONLY)
You can use this function to set the head-
lights to change between low beam and high
beam automatically. The system recognizes
vehicles with their lights on, either approach-
ing from the opposite direction or traveling in
front of your vehicle, and consequently
switches the headlights from high beam to
low beam.
The system automatically adapts the low
beam headlight range depending on the dis-
tance to the other vehicle. Once the system
no longer detects any other vehicles, it
switches on the high beam headlights again.
The system's optical sensor is located behind
the windshield near the overhead control
panel.
WARNING
•The high beam assist system is a conve-
nience but is not a substitute for safe
driving operation. The driver should re-
main alert at all times, ensure safe driv-
ing practices and switch the high beams
and low beam manually when necessary.
•The high beam or low beam may not
switch automatically under the follow-
ing conditions. Switch the high beam
and low beam manually. – During bad weather (rain, fog, snow,
wind, etc.).
– When a light source similar to a head-
light or tail light is in the vicinity of
the vehicle.
– When the headlights of the oncoming
vehicle or the leading vehicle are
turned off, when the color of the light
is affected due to foreign materials
on the lights, or when the light beam
is out of position.
– When there is a sudden, continuous
change in brightness.
– When driving on a road that passes
over rolling hills, or a road that has
level differences.
– When driving on a road with many
curves.
NSD594NDS595
2-68Instruments and controls

The HomeLink® Universal Transceiver, inte-
grated in the vehicle's inside rear view mirror,
provides a convenient way to consolidate the
functions of up to three individual hand-held
transmitters into one built-in device.
HomeLink® Universal Transceiver:
•Will operate most Radio Frequency (RF)
devices such as garage doors, gates, home
and office lighting, entry door locks and
security systems.
•Is powered by your vehicle’s battery. No
separate batteries are required. If the ve-
hicle’s battery is discharged or is discon-
nected, HomeLink® will retain all pro-
gramming.
When the HomeLink® Universal Transceiver
is programmed, retain the original transmit-
ter for future programming procedures (Ex-
ample: new vehicle purchases). Upon sale of
the vehicle, the programmed HomeLink®
Universal Transceiver buttons should be
erased for security purposes. For additional
information, refer to "Programming
HomeLink® " later in this section.
WARNING
•Do not use the HomeLink® Universal
Transceiver with any garage door
opener that lacks safety stop and re-
verse features as required by federal
safety standards. (These standards be-
came effective for opener models manu-
factured after April 1, 1982). A garage
door opener which cannot detect an ob-
ject in the path of a closing garage door
and then automatically stop and re-
verse, does not meet current federal
safety standards. Using a garage door
opener without these features increases
the risk of serious injury or death.
•During the programming procedure
your garage door or security gate will
open and close (if the transmitter is
within range). Make sure that people or
objects are clear of the garage door,
gate, etc. that you are programming.
•Your vehicle’s engine should be turned
off while programming the HomeLink®
Universal Transceiver. NOTE
Certain garage door drives are incompatible
with the integrated garage door opener. If
you have difficulty programing the inte-
grated garage door opener, it is recom-
mended you contact your INFINITI retailer.
PROGRAMMING HOMELINK®
If you have any questions or are having diffi-
culty programming your HomeLink® but-
tons, refer to the HomeLink® web site at:
www.homelink.com or call
1-800-355-3515.
HOMELINK® UNIVERSAL
TRANSCEIVER (IF EQUIPPED)
2-88Instruments and controls

1. Turn the ignition key to the ON position.
2. Press and hold one of buttons
2to4on
the HomeLink®.
HomeLink® is now in programing mode.
After a short time, indicator light
1lights
up yellow.
Indicator light
1lights up yellow as soon
as button
2,3or4is programed for
the first time. If the selected button has
already been programed, indicator light
1will only light up yellow after ten sec-
onds have elapsed.
3. Release button
2,3or4. Indicator
light
1flashes yellow.
4. Position the end of your hand-held trans- mitter
52–8 inches (5–20 cm) away
from the HomeLink® surface, keeping the
HomeLink® indicator light
1in view. 5. Press and hold button
6on the hand held
transmitter until indicator light
1lights
up green. When indicator light
1: lights
up green: programing is finished.
When indicator light
1flashes green:
programing was successful. The next step
is to synchronize the rolling code.
6. Release button
6on the hand held trans-
mitter
5for the garage door drive sys-
tem.
If indicator light
1lights up red: repeat
the programing procedure for the corre-
sponding button on the rear-view mirror.
When doing so, vary the distance be-
tween the hand held transmitter
5and
the rear-view mirror.
The required distance between the hand
held transmitter
5and the integrated ga-
rage door opener depends on the garage
door drive system. Several attempts might
be necessary. You should test every posi-
tion for at least 25 seconds before trying
another position.
Synchronizing the rolling code
If the garage door system uses a rolling code,
you will also have to synchronize the garage
door system with the integrated garage door
opener in the rear-view mirror. To do this you
will need to use the programing button on the door drive control panel. The programing
button may be positioned at different loca-
tions depending on the manufacturer. It is
usually located on the door drive unit on the
garage ceiling.
Familiarize yourself with the garage door
drive operating instructions before carrying
out the following steps.
Your vehicle must be within reach of the ga-
rage door or gate opener drive. Make sure
that neither your vehicle nor any persons/
objects are present within the sweep of the
door or gate.
1. Turn the ignition key to the ON position.
2. Get out of the vehicle.
3. Press the programing button on the door
drive unit.
Usually, you now have 30 seconds to ini-
tiate the next step.
4. Get into the vehicle.
5. Press previously programed button
2,3or4on the HomeLink® until the door
closes.
The rolling code synchronization is then com-
plete.
NDI1631
Instruments and controls2-89