2018 INFINITI QX30 engine

Backing up behind a projecting
object
The positionCis shown farther than the
position
Bin the display. However, the po-
sition
Cis actually at the same distance asthe position
A. The vehicle may hit the object
when backing up to the position
Aif the
object projects over the actual moving course.
HOW TO PARK WITH
PREDICTED COURSE LINES
WARNING
•If the tires are replaced with different
sized tires, the predicted course lines
may not be displayed correctly.
•On a snow-covered or slippery road,
there may be a difference between the
predicted course lines and the actual
course.
•The displayed lines will appear slightly
off to the right because the rear view
camera is not installed in the rear center
of the vehicle.
•If the battery is disconnected or be-
comes discharged, the predicted course
lines may be displayed incorrectly. If this
occurs, please perform the following
procedures:
–Turn the steering wheel from lock to
lock while the engine is running.
–Drive the vehicle on a straight road
for more than 5 minutes.
•When the steering wheel is turned with
the ignition switch in the ACC position,
the predicted course lines may be dis-
played incorrectly.
SAA1980
Display screen, heater and air conditioner, and audio system4-17

WARNING
•The heater and air conditioner operate
only when the engine is running.
•Never leave children or adults who
would normally require the support of
others alone in the vehicle. Pets should
not be left alone either. They could un-
knowingly activate switches or controls
and inadvertently become involved in a
serious accident and injure themselves.
On hot, sunny days, temperatures in a
closed vehicle could quickly become high
enough to cause severe or possibly fatal
injuries to people or animals.
•Do not use the recirculation mode for
long periods as it may cause the interior
air to become stale and the windows to
fog up.
•Do not adjust the heating and air condi-
tioning controls while driving so that
full attention may be given to vehicle
operation.
The heater and air conditioner operate when
the engine is running. The air blower will op-
erate even if the engine is turned off and the
ignition switch is in the ON position.NOTE
•Condensation forms inside the air condi-
tioning unit when the air conditioner (if
equipped) is running, and is safely dis-
charged underneath your vehicle.
Traces of water on the ground are there-
fore normal.
•Odors from inside and outside the vehicle
can build up in the air conditioner unit.
Odor can enter the passenger compart-
ment through the ventilators.
When parking, set the heater and air con-
ditioner controls to turn off air recircula-
tion to allow fresh air into the passenger
compartment. This should help reduce
odors inside the vehicle.
Observe the settings recommended on the
following pages. The windows could other-
wise mist up. To prevent the windows from
misting up
•Switch off climate control only briefly.
•Switch on air-recirculation mode only
briefly.
•Switch on the cooling with air dehumidifi-
cation function.
•Switch on the windshield demisting func-
tion briefly, if required.The air-conditioning system/automatic cli-
mate control regulates the temperature and
the humidity of the vehicle interior and filters
undesirable substances from the air.
The air-conditioning system/automatic cli-
mate control can only be operated when the
engine is running. Optimum operation is only
achieved with the side windows closed.
Always keep the ventilation flaps behind the
side panelling clear. Otherwise the vehicle will
not be ventilated correctly.
NOTE
•Ventilate the vehicle for a brief period dur-
ing warm weather. This will speed up the
cooling process and the desired interior
temperature will be reached more quickly.
•The integrated filter filters out most par-
ticles of dust and soot and completely fil-
ters out pollen. With automatic climate
control, gaseous pollutants and odors will
also be reduced. A clogged filter reduces
the amount of air supplied to the vehicle
interior. For this reason, you should always
observe the interval for replacing the filter,
which is specified in the Service Booklet.
As this depends on environmental condi-
tions, for example heavy air pollution, the
interval may be shorter than stated in the
Service Booklet.
HEATER AND AIR CONDITIONER
Display screen, heater and air conditioner, and audio system4-29

•Recommendation for air distribution in
winter: select theandsettings.
Recommendation for air distribution in
summer: select the
orandsettings.
•Only use the "Windshield demisting" func-
tion briefly until the windshield is clear again
•Only use air-recirculation mode briefly, for
example if there are unpleasant outside
odors or when in a tunnel. The windows
could otherwise mist up as no fresh air is
drawn into the vehicle in air-recirculation
mode
•If you change the settings of the climate
control system, the climate status display
appears for approximately three seconds
at the bottom of the screen in the central
display (see separate operating instruc-
tions). You will see the current settings of
the various climate control functions.
Switching air-conditioning system
on/off
Make sure the ignition switch is in the ON
position.
To switch on:turn control
5clockwise to the
desired position (except position0).
To switch off:turn control
5counter-
clockwise to position0.
Activating/deactivating the cooling
with air dehumidification function
If you deactivate the "Cooling with air dehu-
midification" function, the air inside the ve-
hicle will not be cooled. The air inside the
vehicle will also not be dehumidified. The
windows can mist up more quickly. There-
fore, only deactivate the "Cooling with air
dehumidification" function briefly.
The "Cooling with air dehumidification" func-
tion is only available when the engine is run-
ning. The air inside the vehicle is cooled and
dehumidified according to the temperature
selected.
Condensation may drip from the underside of
the vehicle when cooling mode is active. This
is normal and not a sign that there is a mal-
function.
To activate:
Press the
button The indicator light in
thebutton lights up.
To deactivate:
Press the
button. The indicator light in
thebutton goes out. The cooling with
air dehumidification function has a delayed
switch-off feature.Problems with the "Cooling with air dehu-
midification" function:
Problem:The indicator light in the
but-
ton flashes three times or remains off. The
cooling with air dehumidification function
cannot be activated.
Cause and solution:The cooling with air de-
humidification function has been deactivated
due to a malfunction. Have the system
checked. It is recommended you visit an
INFINITI retailer for this service.
Setting the temperature
You can set the temperature for the entire
vehicle. The set temperature is automatically
maintained at a constant level.
To increase or reduce the temperature: turn
control
1counterclockwise or clockwise.
Only change the temperature setting in small
increments. Start at 70° F (22° C).
Setting the air distribution
Directs the airflow through the demis-
ter ventilators.
Directs the airflow through the center
and side air ventilators.
Directs the airflow through the foot-
well air ventilators.
Display screen, heater and air conditioner, and audio system4-31

NOTE
•You can also activate several of the air
distribution settings simultaneously. In or-
der to do this, press several of the air dis-
tribution buttons. The air is then routed
through different air ventilators.
•Regardless of the air distribution setting,
airflow is always directed through the side
air ventilators. The side air ventilators can
only be closed if the adjusters are turned
clockwise until they engage.
To set air distribution:
1. Make sure the engine is running.
2. Press one or more of the
,,orbuttons. The corresponding indica-
tor light comes on.
Setting the airflow
1. Make sure the ignition switch is in the ON
position.
2. To increase or reduce airflow: turn control
5counterclockwise or clockwise.
Defogging the windshield
You can use this function to de-ice the wind-
shield or to defog the inside of the windshield
and the side windows.
NOTE
You should only select the "Windshield de-
misting" function until the windshield is clear
again.
Activating the "Windshield demisting"
function:
Make sure the ignition switch is in the ON
position.
To activate: press the
button The indi-
cator light in thebutton lights up.
The climate control system switches to the
following functions:
•High airflow
•High temperature
•Air distribution to the windshield and front
side windows
•Air-recirculation mode offNOTE
•The "Windshield demisting" function auto-
matically sets the blower output to the
optimum demisting effect. As a result, the
airflow may increase or decrease auto-
matically after the
button is pressed.
•You can adjust the blower output manu-
ally while the "Windshield demisting" func-
tion is in operation. Turn airflow control
5counterclockwise or clockwise.
Deactivating the "Windshield demisting"
function:
Press the
button. The indicator light in
thebutton goes out. The previous set-
tings are reactivated. Air-recirculation mode
remains deactivated.
or
Turn temperature control
1counterclock-
wise or clockwise.
Defogging the windows
Windows misted up on the inside:
1. Activate the
"Cooling with air dehu-
midification" function.
2. If the windows continue to mist up, acti-
vate the
"Windshield demisting"
function.
4-32Display screen, heater and air conditioner, and audio system

NOTE
You should only select this setting until the
windshield is clear again.
Windows misted up on the outside:
1. Activate the windshield wipers.
2. Set the air distribution to
or.
NOTE
You should only select this setting until the
windows are clear again.
Air recirculation mode
You can deactivate the flow of fresh air if
unpleasant odors are entering the vehicle
from outside. The air already inside the ve-
hicle will then be recirculated.
If you activate air-recirculation mode, the
windows can mist up more quickly, in particu-
lar at low temperatures. Only use air recircu-
lation mode briefly to prevent the windows
misting up.
Activating air recirculation mode:
Make sure the ignition switch is in the ON
position.
Press the
button. The indicator light in
thebutton lights up.Deactivating air recirculation mode:
Press the
button. The indicator light in
thebutton goes out.
NOTE
Air-recirculation mode is deactivated auto-
matically:
•After approximately five minutes at out-
side temperatures below approximately
45° F (7°C).
•After approximately five minutes if the
"Cooling with air dehumidification" func-
tion is deactivated.
•After approximately 30 minutes at outside
temperatures above approximately 45° F
(7°C) if the cooling with air dehumidifica-
tion function is activated.
Idle Stop/Start function
During automatic engine switch-off, the Cli-
mate control only operates at a reduced ca-
pacity. If you require the full climate control
output, you can switch off the Idle Stop/
Start function by pressing the ECO button
(see " Idle Stop/Start System (if equipped)").
Display screen, heater and air conditioner, and audio system4-33

•If you change the settings of the climate
control system, the climate status display
appears for approximately three seconds
at the bottom of the screen in the center
display (see separate operating instruc-
tions). You will see the current settings of
the various climate control functions.
Idle Stop/Start function
During automatic engine switch-off, the Cli-
mate control only operates at a reduced ca-
pacity. If you require the full climate control
output, you can switch off the Idle Stop/
Start function by pressing the ECO button
(see " Idle Stop/Start System (if equipped)").
Switching automatic climate
control on/off
When the climate control is switched off, the
air supply and air circulation are also
switched off. The windows could mist up.
Therefore, only switch off climate control
briefly.
Make sure the ignition switch is in the ON
position.
To activate:
Press the
button The indicator light in
thebutton lights up. Airflow and air
distribution are set to automatic mode.or
Press thebutton. The indicator light in
thebutton goes out. The previous settings
are reactivated.
To deactivate:
Press the
button. The indicator light in
thebutton lights up.
NOTE
Automatic climate control: switch on climate
control primarily using the
button.
Activating/deactivating the cooling
with air dehumidification function
If you deactivate the "Cooling with air dehu-
midification" function, the air inside the ve-
hicle will not be cooled. The air inside the
vehicle will also not be dehumidified. The
windows can mist up more quickly. There-
fore, only deactivate the "Cooling with air
dehumidification" function briefly.
The "Cooling with air dehumidification" func-
tion is only available when the engine is run-
ning. The air inside the vehicle is cooled and
dehumidified according to the temperature
selected.
Condensation may drip from the underside of
the vehicle when cooling mode is active. This
is normal and not a sign that there is a mal-
function.To activate:
Press the
button The indicator light in
thebutton lights up.
To deactivate:
Press the
button. The indicator light in
thebutton goes out. The cooling with
air dehumidification function has a delayed
switch-off feature.
Problems with the "Cooling with air dehu-
midification" function:
Problem:The indicator light in the
but-
ton flashes three times or remains off. The
cooling with air dehumidification function
cannot be activated.
Cause and solution:The cooling with air de-
humidification function has been deactivated
due to a malfunction. Have the system
checked. It is recommended you visit an
INFINITI retailer for this service.
Setting automatic climate control
to automatic mode
Only automatic climate control features the
"Control climate control automatically" func-
tion.
In automatic mode, the set temperature is
maintained automatically at a constant level
Display screen, heater and air conditioner, and audio system4-35

The system automatically regulates the tem-
perature of the dispensed air, the airflow and
the air distribution.
The automatic mode functions optimally
when the "Cooling with air dehumidification"
function is activated. If desired, cooling with
air dehumidification can be deactivated.
If you deactivate the "Cooling with air-
dehumidification" function, the air inside the
vehicle will not be cooled. The air inside the
vehicle will also not be dehumidified. The
windows can mist up more quickly. There-
fore, only deactivate the "Cooling with air-
dehumidification" function briefly.
To set climate control to automatic mode:
Make sure the ignition switch is in the ON
position.
Set the desired temperature.
To activate: press the
button The indi-
cator light in thebutton lights up. Auto-
matic air distribution and airflow are activated.
To switch to manual mode: press theorbutton
or
Press the
orbutton. The indicator
light in thebutton goes out. Automatic
air distribution and airflow are deactivated.
Setting the temperature
Different temperatures can be set for the
driver's and front-passenger sides. The set
temperature is automatically maintained at a
constant level.
Make sure the ignition switch is in the ON
position.
To increase or reduce temperature: turn con-
trol
1or9counterclockwise or clockwise.
Only change the temperature setting in small
increments. Start at 70° F (22° C).
Setting the air distribution
Directs the airflow through the demis-
ter ventilators.
Directs the airflow through the center
and side air ventilators.
Directs the airflow through the foot-
well air ventilators.
Directs the airflow through the center
and side air ventilators as well as the
footwell air ventilators.
Directs the airflow through the center
and side air ventilators as well as the
demister ventilators.
Directs the airflow through the foot-
well and demister ventilators.
Directs the airflow through the demis-
ter ventilators, the center and side air
ventilators as well as the footwell air
ventilators.NOTE
Regardless of the air distribution setting,
airflow is always directed through the side
air ventilators. The side air ventilators can
only be closed if the adjusters are turned
clockwise until they engage.
To set the air distribution:
1. Make sure the engine is running.
2. Press the
orbutton repeat-
edly until the desired symbol appears in
the display.
Setting the airflow
1. Make sure the ignition switch is in the ON
position.
2. To increase or reduce airflow: press the
orbutton.
Switching the ZONE function
on/off
This function is only available with automatic
climate control.
To activate:press the
button. The in-
dicator light in thebutton lights up. The
temperature setting for the driver's side is not
adopted for the front-passenger side.
To deactivate:press the
button. The
indicator light in thebutton goes out.
4-36Display screen, heater and air conditioner, and audio system

5 Starting and driving
Precautions when starting and driving.........5-2
Exhaust gas (carbon monoxide)...........5-2
Three-way catalyst (if equipped)..........5-2
Tire Pressure Monitoring System (TPMS).....5-3
On pavement and off-road driving
precautions........................5-8
Avoiding collision and rollover............5-8
Off-road recovery...................5-9
Rapid air pressure loss.................5-9
Drinking alcohol/drugs and driving........5-10
Driving safety precautions.............5-10
All-wheel drive (AWD) driving safety
precautions (if so equipped).............5-12
Infiniti Vehicle Immobilizer system...........5-13
Ignition switch.......................5-13
Key positions......................5-13
Push-button ignition switch (if equipped)......5-14
Key positions with the push-button ignition
switch..........................5-15
Removing the start/stop button..........5-15
Emergency engine shut off.............5-16
Before starting engine..................5-16
Starting engine.......................5-16
Starting procedure with the key..........5-16
Starting procedure using the push-button
ignition switch (if equipped).............5-17
Driving the vehicle.....................5-18Driving with Automatic Transmission......5-18
Parking brake........................5-27
Applying/releasing manually............5-27
Applying automatically (vehicles with automatic
transmission)......................5-28
Releasing automatically...............5-28
Emergency braking..................5-28
Idle Stop/Start System (if equipped).........5-29
Automatic engine switch-off............5-29
Automatic engine start...............5-30
Deactivating/activating the Idle Stop/Start
function.........................5-30
Lane departure warning (LDW) system
(if equipped).......................
.5-31
LDW system operation...............5-32
How to enable/disable the LDW system. . . .5-33
LDW system limitations...............5-33
LDW system temporarily unavailable.......5-35
System malfunction.................5-35
System maintenance.................5-36
Blind Spot Warning (BSW) system (if equipped) . .5-36
BSW system operation...............5-38
How to enable/disable the BSW system. . . .5-40
BSW system limitations...............5-40
System temporarily unavailable..........5-45
Radar maintenance..................5-46
FCC Notice.......................5-46