2018 INFINITI QX30 light

1 Safety — seats, seat belts and
supplemental restraint system
Seats..............................1-2
Front seats........................1-3
Rear seats.........................1-5
Armrest (if equipped)..................1-7
Head restraints/Headrests................1-7
Adjustable head restraint components.......1-8
Remove..........................1-8
Install............................1-9
Adjust...........................1-9
Seat belts..........................1-10
Precautions on seat belt usage..........1-10
Pregnant women...................1-12
Injured persons.....................1-12
Seat belt warning light................1-13
Three-point type seat belt with retractor. . . .1-13
Seat belt extenders..................1-16
Seat belt maintenance................1-16
Child safety.........................1-17
Infants..........................1-17
Small children......................1-18Larger children.....................1-18
Child restraints.......................1-19
Precautions on child restraints...........1-19
Rear-facing child restraint installation using
LATCH..........................1-23
Rear-facing child restraint installation using the
seat belts........................1-24
Forward-facing child restraint installation using
LATCH..........................1-27
Forward-facing child restraint installation
using the seat belts..................1-29
Booster seats.....................1-34
Supplemental Restraint System (SRS)........1-37
Precautions on Supplemental Restraint System
(SRS)...........................1-37
Supplemental air bag systems...........1-43
Supplemental air bag warning labels.......1-53
Supplemental air bag warning light........1-53
Repair and replacement procedure........1-54

FRONT SEATS
Manual seat adjustment
Forward and backward:
Pull the lever
1up and hold it while sliding
the seat forward or backward to the pre-
ferred position. Release the lever to lock the
seat in position.
Seat cushion angle (if equipped):
Adjust the angles so that your thighs are
lightly supported. Turn handwheel
2for-
wards or backwards.Seat lifter (if equipped):
Repeatedly pull up or push down the adjust-
ing lever
3, to adjust the seat height to the
desired position.
Seatback angle:
Relieve the pressure on the seatback and turn
handwheel
4forwards or backwards.
The reclining feature allows the adjustment
of the seatback for occupants of different
sizes to help obtain the proper seat belt fit.
(See "Seat belts" later in this section.)
The seatback may be reclined to allow occu-
pants to rest when the vehicle is parked.Lumbar support:
The lumbar support feature provides lower
back support to the driver.
Push each side of the adjusting switch to
adjust the seat lumbar area until the desired
position is achieved.
1To raise the seatback contour
2To soften the seatback contour
3To lower the seatback contour
4To harden the seatback contour
NIC2605NIC2607
Safety — seats, seat belts and supplemental restraint system1-3

•The seat belt should be properly ad-
justed to a snug fit. Failure to do so may
reduce the effectiveness of the entire
restraint system and increase the
chance or severity of injury in an acci-
dent. Serious injury or death can occur if
the seat belt is not worn properly.
•Always route the shoulder belt over
your shoulder and across your chest.
Never put the belt behind your back, un-
der your arm or across your neck. The
belt should be away from your face and
neck, but not falling off your shoulder.
•Position the lap belt as low and snug as
possible AROUND THE HIPS, NOT THE
WAIST. A lap belt worn too high could
increase the risk of internal injuries in an
accident.
•Be sure the seat belt tongue is securely
fastened to the proper buckle.
•Do not wear the seat belt inside out or
twisted. Doing so may reduce its effec-
tiveness.
•Do not allow more than one person to
use the same seat belt.
•Never carry more people in the vehicle
than there are seat belts.
•If the seat belt warning light glows con-
tinuously while the ignition is turned ON
with all doors closed and all seat belts
fastened, it may indicate a malfunction
in the system. Have the system checked.
It is recommended that you visit an
INFINITI retailer for this service.
•No changes should be made to the seat
belt system. For example, do not modify
the seat belt, add material or install de-
vices that may change the seat belt
routing or tension. Doing so may affect
the operation of the seat belt system.
Modifying or tampering with the seat
belt system may result in serious per-
sonal injury.
•Once a seat belt pretensioner has acti-
vated, they cannot be reused and must
be replaced together with the retractor.
It is recommended that you visit an
INFINITI retailer for this service.
•All seat belt assemblies, including re-
tractors and attaching hardware,
should be inspected after any collision.
It is recommended that you visit an
INFINITI retailer for this service.
INFINITI recommends that all seat belt
assemblies in use during a collision be
replaced unless the collision was minor
and the belts show no damage and con-tinue to operate properly. Seat belt as-
semblies not in use during a collision
should also be inspected and replaced if
either damage or improper operation is
noted.
•All child restraints and attaching hard-
ware should be inspected after any col-
lision. Always follow the restraint
manufacturer’s inspection instructions
and replacement recommendations. The
child restraints should be replaced if
they are damaged.
PREGNANT WOMEN
INFINITI recommends that pregnant women
use seat belts. The seat belt should be worn
snug, and always position the lap belt as low
as possible around the hips, not the waist.
Place the shoulder belt over your shoulder
and across your chest. Never put the lap/
shoulder belt over your abdominal area. Con-
tact your doctor for specific recommenda-
tions.
INJURED PERSONS
INFINITI recommends that injured persons
use seat belts. Check with your doctor for
specific recommendations.
1-12Safety — seats, seat belts and supplemental restraint system

SEAT BELT WARNING LIGHT
The seat belt warning light reminds you to
fasten your seat belts. The light illuminates if
the engine is started, all doors are closed and
the driver’s and/or front passenger’s seat
belt is unfastened. It will remain illuminated
until the driver and/or front passenger fas-
tens their seat belt. A chime will sound once
the vehicle is in motion.
If the seat belt warning light flashes, together
with an intermittent warning tone, this means
that the driver or passenger has not fastened
their seat belt, and the speed of the vehicle is
exceeding 15 MPH (25 km/h).
For additional information, refer to "Warning
lights, indicator lights and audible reminders".
THREE-POINT TYPE SEAT BELT
WITH RETRACTOR
WARNING
•Every person who drives or rides in this
vehicle should use a seat belt at all times.
Children should be in the rear seats and
in an appropriate restraint.
•Do not ride in a moving vehicle when the
seatback is reclined. This can be danger-
ous. The shoulder belt will not be against
your body. In an accident, you could be
thrown into it and receive neck or other
serious injuries. You could also slide un-
der the lap belt and receive serious inter-
nal injuries.
•For the most effective protection when
the vehicle is in motion, the seat should
be upright. Always sit well back and up-
right in the seat with both feet on the
floor and adjust the seat belt properly.
•Do not allow children to play with the
seat belts. Most seating positions are
equipped with Automatic Locking Re-
tractor (ALR) mode seat belts. If the
seat belt becomes wrapped around a
child’s neck with the ALR mode acti-
vated, the child can be seriously injured
or killed if the seat belt retracts and be-
comes tight. This can occur even if the
vehicle is parked. Unbuckle the seat belt
to release the child. If the seat belt can-
not be unbuckled or is already unbuck-
led, release the child by cutting the seat
belt with a suitable tool (such as a knife
or scissors) to release the seat belt.
Fastening the seat belts
1. Adjust the seat. (See "Seats" earlier in this
section.)
2. Slowly pull the seat belt out of the retrac-
tor and insert the tongue into the buckle
until you hear and feel the latch engage.
NIC2743
Safety — seats, seat belts and supplemental restraint system1-13

•The retractor is designed to lock dur-
ing a sudden stop or on impact. A slow
pulling motion permits the belt to
move and allows you some freedom of
movement in the seat.
•If the seat belt cannot be pulled from
its fully retracted position, firmly pull
the belt and release it. Then smoothly
pull the belt out of the retractor.
3. Position the lap belt portionlow and snug
on the hipsas shown4. Pull the shoulder belt portion toward the
retractor to take up extra slack. Be sure
the shoulder belt is routed over your
shoulder and across your chest.
The front passenger seat and the rear seating
positions three-point seat belts have two
modes of operation:
•Emergency Locking Retractor (ELR)
•Automatic Locking Retractor (ALR)
The ELR mode allows the seat belt to extend
and retract to allow the driver and passen-
gers some freedom of movement in the seat.
The ELR locks the seat belt when the vehicle
slows down rapidly or during certain impacts.The ALR mode (child restraint mode) locks
the seat belt for child restraint installation.
When the ALR mode is activated, the seat
belt cannot be extended again until the seat
belt tongue is detached from the buckle and
fully retracted. The seat belt returns to the
ELR mode after the seat belt fully retracts.
For additional information, refer to "Child
restraints" later in this section. The ALR mode
should be used only for child restraint instal-
lation. During normal seat belt use by an oc-
cupant, the ALR mode should not be acti-
vated. If it is activated, it may cause
uncomfortable seat belt tension. It can also
change the operation of the front passenger
air bag. For additional information, refer to
"Front passenger air bag and status light".
WARNING
When fastening the seat belts, be certain
that the seatbacks are completely secured
in the latched position. If they are not com-
pletely secured, passengers may be injured
in an accident or sudden stop.
SSS0292ZSSS0290Z
1-14Safety — seats, seat belts and supplemental restraint system

restraint could tip over or be loose and
cause injury to a child in a sudden stop or
collision. Also, it can change the operation
of the front passenger air bag. For addi-
tional information, refer to "Front passen-
ger air bag and status light".
For additional information, refer to all Warn-
ings and Cautions in the "Child safety" and
"Child restraints" before installing a child re-
straint.
Do not use the lower anchors if the combined
weight of the child and the child restraint
exceeds 65 lb (29.5 kg). If the combined
weight of the child and the child restraint is
greater than 65 lb (29.5 kg), use the vehicle
seat belt (not the lower anchors) to install the
child restraint. Be sure to follow the child
restraint manufacturer's instructions for in-
stallation.
Follow these steps to install a forward-
facing child restraint using the vehicle seat
belt in the rear seats or in the front passenger
seat:1.If you must install a child restraint in the
front seat, it should be placed in a
forward-facing direction only. Move the
seat to the rearmost position. Child re-
straints for infants must be used in the
rear-facing direction and, therefore,
must not be used in the front seat.2. Position the child restraint on the seat.
Always follow the child restraint manu-
facturer's instructions. The back of the
child restraint should be secured against
the vehicle seatback. If necessary, adjust
or remove the head restraint/headrest to
obtain the correct child restraint fit. If the
head restraint/headrest is removed, store
it in a secure place.Be sure to reinstall the
head restraint/headrest when the child
restraint is removed.For additional infor-
mation about head restraint/headrest
adjustment, removal and installation, re-
fer to "Head restraints/Headrests".
If the seating position does not have an
adjustable head restraint/headrest and it
is interfering with the proper child re-
straint fit, try another seating position or a
different child restraint.
WRS0699Z
Forward-facing (front passenger seat) —
step 1
1-30Safety — seats, seat belts and supplemental restraint system

6. Remove any additional slack from the seat
belt; press downward and rearward firmly
in the center of the child restraint with
your knee to compress the vehicle seat
cushion and seatback while pulling up on
the seat belt.
7. Tighten the tether strap according to the
manufacturer's instructions to remove
any slack.8. After attaching the child restraint, test it
before you place the child in it. Push it
from side to side while holding the child
restraint near the seat belt path. The
child restraint should not move more than
1 inch (25 mm), from side to side. Try to
tug it forward and check to see if the belt
holds the restraint in place. If the restraint
is not secure, tighten the seat belt as nec-
essary, or put the restraint in another seat
and test it again. You may need to try a
different child restraint. Not all child re-
straints fit in all types of vehicles.
9. Check to make sure the child restraint is
properly secured prior to each use. If the
seat belt is not locked, repeat steps 2
through 8.10. If the child restraint is installed in the
front passenger seat, place the ignition
switch in the ON position. Either the
indicator
light or
indicator light will illuminate depending
on the size of the child and the type of
child restraint used. See "Front passen-
ger air bag and status light". After the
child restraint is removed and the seat
belt is fully retracted, the ALR mode
(child restraint mode) is canceled.
If necessary, system operation can be
checked by using a special tool. It is rec-
ommended that you visit an INFINITI
retailer for this service. Until you have
confirmed system operation, move the
child restraint to another position. See
"Troubleshooting" later in this section.
WRS0681Z
Forward-facing — step 6
WRS0698Z
Forward-facing — step 8
SSS0676Z
Forward-facing — step 10
1-32Safety — seats, seat belts and supplemental restraint system

7. If the booster seat is installed in the front
passenger seat, place the ignition switch
in the ON position. Either the GER AIR BAG ON>
1indicator light
or
2indicator light will illuminate depending on
the size of the child and the type of
booster seat used. See "Front passenger
air bag and status light".
PRECAUTIONS ON
SUPPLEMENTAL RESTRAINT
SYSTEM (SRS)
This Supplemental Restraint System (SRS)
section contains important information con-
cerning the following systems:
•Driver and passenger supplemental front
impact air bags (INFINITI Advanced Air
Bag System)
•Driver and passenger supplemental knee
air bags
•Front seat-mounted side-impact supple-
mental air bags
•Roof-mounted curtain side-impact and
rollover supplemental air bags
•Seat belts with pretensioner
Supplemental front-impact air bag
system
The INFINITI Advanced Air Bag System can
help cushion the impact force to the head and
chest of the driver and front passenger in
certain frontal collisions.
Driver and passenger supplemental
knee air bags
This system can help cushion the impact
force to the driver's and passenger's knees in
certain collisions.
Front seat-mounted side-impact
supplemental air bag system
This system can help cushion the impact
force to the chest and pelvis areas of the
driver and front passenger in certain side-
impact collisions. The side air bag is designed
to inflate on the side where the vehicle is
impacted.
Roof-mounted curtain side-impact
and rollover supplemental air bags
This system can help cushion the impact
force to the head of occupants in the out-
board seating positions in certain side-impact
or rollover collisions. In a side impact, the
curtain air bags are designed to inflate on the
side where the vehicle is impacted. In a roll-
over, curtain air bags on both sides are de-
signed to inflate and remain inflated for a
short time.
NIC2740
SUPPLEMENTAL RESTRAINT
SYSTEM (SRS)
Safety — seats, seat belts and supplemental restraint system1-37