2018 INFINITI Q70 HYBRID fuel pressure

8
• Normal wear and tear, including dings, dents, chips, or scratches
• Damage caused by any automated or manually operated car wash or by using a
pressure washer
NOTE: Complaints related to failure to comply
with proper use of the vehicle as described
in the applicable Owner’s Manual (including
the lack of availability or use of proper fluid),
or the vehicle’s lack of compliance with local
regulations or environmental requirements of
any country (other than the U.S. or Canada) are
NOT covered by this warranty.
DAMAGE OR FAILURES DUE TO
ALTERATION OR MODIFICATION
This warranty does not cover damage, failures
or corrosion resulting from or caused by:
• Alteration, tampering, or improper repair
• Installation of non-Infiniti approved accessories or components
• Improper installation of any Infiniti approved aftermarket accessory or component
• A vehicle whose odometer mileage has been altered, or the odometer repaired or replaced
and the actual vehicle mileage cannot be
correctly and readily determined
SALVAGE TITLEThis limited warranty does not apply to any
vehicle, and is rendered void if the vehicle is
(or ever has been) issued a “salvage” or similar
title including, but not limited to junk, scrap,
rebuilt, or flood titles, under any state’s law; or
has ever been determined to be a “total loss” or equivalent by any insurance company, such
as by payment of a cash payment of a claim in
lieu of repairs because of a determination that
the cost of repairs exceeded the actual cash
value of the vehicle.
DAMAGE, FAILURES OR CORROSION
FROM ENVIRONMENTAL CONDITIONS
This warranty does not cover damage, failures
or corrosion resulting from or caused by:
• Stone chipping, chemical fallout, tree sap,
salt, hail, windstorm, lightning, flood or other
environmental conditions.
• The items listed below are not covered under corrosion coverage (perforation from
corrosion).
ßExhaust system components.
ß Corrosion other than perforation, such
as cosmetic or surface corrosion due to
defects in material or workmanship. This
is covered under the Basic Coverage of
the New Vehicle Limited Warranty.
GRADUAL CAPACITY LOSSThe Lithium-ion battery, like all lithium-ion
batteries, will experience gradual capacity loss
with time and use. Loss of battery capacity
due to or resulting from gradual capacity loss
is NOT covered under this warranty. See your
Owner’s Manual for important tips on how to
maximize the life and capacity of the “Lithium-
ion battery.”
DAMAGE, FAILURES OR CORROSION
DUE TO LACK OF OR IMPROPER
MAINTENANCE REPAIRS
This warranty does not cover damage, failures
or corrosion resulting from or caused by:
• Lack of performance of proper maintenance
services as outlined in your Owner’s Manual.
• Fuel, fluids, or lubricants that are contaminated or that do not meet the
specification as outlined in your Owner’s
Manual.
• Use of parts not equivalent in quality or design to parts supplied by Infiniti for use on
Infiniti vehicles.
MAINTENANCE SERVICE EXPENSEThis warranty does not cover normal
maintenance services as specified in both
your Owner’s Manual and Infiniti Service
& Maintenance Guide such as cleaning
and polishing, wheel alignment, headlight
aiming, replacement of filters, replacement of
windshield wiper inserts, lubricants, coolant,
worn brake shoes, pads, drums and rotors and
worn clutch discs, for example.
SEAT BELTS, TIRES AND EMISSION
CONTROL SYSTEM
Seat belts, tires and the emission control
system are covered by separate warranties.
2018 NEW HYBRID VEHICLE LIMITED WARRANTY

31
DO MAINTAIN PROPER INFLATION
PRESSURE IN YOUR TIRES
Proper inflation pressure is necessary for
optimum tire performance, safety and fuel
economy. Check inflation pressures at least
once a month and before long trips. Use an
accurate tire pressure gauge. Always check
pressures when the tires are cold (when the
vehicle has been driven less than one mile). If
you must check inflation when the tires are
hot, add 4 psi (27 kPa) to the recommended
cold inflation pressure. It is difficult to tell just
by looking at radial tires whether they are
underinflated.*
Furthermore, when operating a vehicle
equipped with radial tires, it is difficult to
notice when a tire has gone flat or nearly flat
since the “feel” of the vehicle does not change
significantly.
Progressive air loss may result from punctures,
cuts, curbing, impacts or partial bead
unseating. Some fitment causes for air loss are
(1) incomplete bead seating, (2) bead tearing
caused by a machine tool due to insufficient
lubrication or improper adjustment, (3) leaking
valve core or rubber valve components should
be replaced when problems are detected and
whenever tires are replaced.
Always maintain inflation pressure at the level
recommended by the vehicle manufacturer as shown on the vehicle placard, vehicle
certification label or in the vehicle Owner’s
Manual:
Underinflation is the leading cause of tire
failure and may result in severe cracking,
component separation or “blowout.” It reduces
tire load capacity, allows excessive sidewall
flexing and increases rolling resistance,
resulting in heat and mechanical damage.
Maintaining proper inflation pressure is the
single most important thing you can do to
promote tire durability and maximize tread life.
Overinflation increases stiffness, which may
deteriorate ride and generate unwanted
vibration. Overinflation also increases the
chances of impact damage.
DON’T OVERLOAD YOUR VEHICLE
OR TIRES
Check your vehicle Owner’s Manual to
determine the load limits. Overloading your
vehicle places stress on your tires and other
critical vehicle components. Overloading a
vehicle can cause poor handling, increased
fuel consumption and may cause tire failure.
Overloading your tires can result in severe
cracking, component separation or "blowout".
Never fit your vehicle with new tires that have
less load capacity than shown on the vehicle
tire placard and remember that optimum
rim width is important for proper tire load
distribution and function. The maximum load capacity stamped on the
sidewalls of P-Metric & European Metric tires
is reduced by 10% when used on a light truck,
utility vehicle or trailer. Never fit P-Metric
or European Metric tires to light trucks that
specify LT-type replacement tires.
DON’T SPIN YOUR TIRES
EXCESSIVELY
Avoid excessive tire spinning when your
vehicle is stuck in snow, ice, mud or sand. The
centrifugal forces generated by a free-spinning
tire/wheel assembly may cause sudden tire
explosion resulting in vehicle damage and/or
serious personal injury to you or a bystander.
Never exceed 35 mph/55 km/h, as indicated
on your speedometer. Use a gentle backward
and forward rocking motion to free your
vehicle for continued driving. Never stand near
or behind a tire spinning at high speeds. For
example, while attempting to push a vehicle
that is stuck or when an on-the-car spin
balance machine is in use.
DO CHECK YOUR TIRES FOR WEAR
Always remove tires from service when
they reach two thirty-seconds of an inch
(2/32) remaining tread depth. All new tires
have treadwear indicators which appear as
smooth banks in the tread grooves when they
wear to the two thirty-seconds of an inch
(2/32) level. Many wet weather accidents
result from skidding on bald or nearly bald
GOODYEAR/DUNLOP TIRE LIMITED WARRANTY
(Continued on next page)* Evidence of air loss or repeated underinflation always requires expert inspection to determine the source of leakage and tire removal to determine repairability. To avoid injury, NEVER attempt to
reinflate a tire that has been run severely underinflated.

32
tires. Excessively worn tires are also more
susceptible to penetrations.
DO CHECK YOUR TIRES FOR
DAMAGE
Frequent (at least monthly) inspection of your
tires for signs of damage and their general
condition is important for safety. If you have
any questions, have your tire Retailer inspect
them. Impacts, penetrations, cracks, knots,
bulges or air loss always require tire removal
and expert inspection. Never perform a
temporary repair or use an inner tube as a
substitute for a proper repair. Only qualified
persons should repair tires.
PROPER TIRE REPAIR
NOTE: Goodyear and Dunlop do not warrant
any inspection or repair process. The repair is
entirely the responsibility of the repairer and
should be made in accordance with established
Rubber Manufacturers Association (RMA)
procedures.
TIRE PRESSURE MONITORING
SYSTEM ALERT
Refer to your vehicle Owner’s Manual for more
information on what to do if the tire pressure
warning system activates.
THE CONVENIENCE (TEMPORARY)
SPARE
The Convenience (Temporary) Spare is designed,
built, and tested to the high engineering
standards set by North America’s leading car
manufacturers and to Goodyear and Dunlop’s own high standards of quality control. It is
designed to take up a minimum of storage
space and, at the same time, fulfill the function
of a spare tire when needed. The spare is kept in
its storage space, fully inflated at 60 psi. To be
sure it is always ready for use, the air pressure
should be checked on a regular basis.
The Convenience (Temporary) Spare can be
used in combination with the original tires
on your vehicle. You can expect a tire tread
life of up to 3,000 miles (4,800 kilometers),
depending on road conditions and your driving
habits. To conserve tire tread life, return the
spare to the storage area as soon as it is
convenient to have the standard tire repaired
or replaced.
The Convenience (Temporary) Spare weighs
less than a standard tire so it’s easier to handle.
It also helps reduce the total car weight which
contributes to fuel economy.
The wheels used with the Convenience
(Temporary) Spare are specifically designed for
use with high pressure spares and should never
be used with any other type tire.
DON’T ATTEMPT TO MOUNT YOUR
OWN TIRES
Serious injury or Death may result from
explosion of tire/ rim assembly due to
improper mounting procedures. Follow tire
manufacturer’s instructions and match tire
diameter to rim diameter. Mount light truck
radials on rims approved for radial service. Do
not apply bead sealer. This can inhibit bead
seating. Lubricate beads and tire rim (including
tube or flap) contact surfaces. Lock assembly
on mounting machine or place in safety cage.
STAND BACK and never exceed 40 psi to
seat beads. Never use a volatile substance or a
rubber “donut” (also known as a bead expander
or “O-Ring”) to aid bead seating. Only
specially-trained persons should mount tires.
DON’T MIX TIRES OF DIFFERENT
SIZES AND TYPES ON THE SAME
AXLE
For optimum handling and control, Goodyear
and Dunlop recommend fitment of four (4) tires
of the same type and size unless otherwise
specified by the vehicle manufacturer.
WARNING: Before you replace your tires,
always consult the vehicle Owner’s Manual and
follow the vehicle manufacturer’s replacement
tire recommendations. Vehicle handling may
be significantly affected by a change in tire
size or type. When selecting tires that are
different than the Original Equipment size,
see a professional installer in order to make
certain that proper clearance, load carrying
capacity and inflation pressure is selected.
Never exceed the maximum load capacity and
inflation pressure listed on the sidewall of the
tire. Always drive safely and obey all traffic
laws. Avoid sudden, sharp turns or lane changes.
Failure to follow this warning may result in loss
of control of the vehicle, leading to an accident
and serious injury or death.
GOODYEAR/DUNLOP TIRE LIMITED WARRANTY
(Continued on next page)