2018 AUDI TT ROADSTER navigation system

Cl co .... N ,....
N ...... 0 ,....
Vl co
Low fuel warning
A message is displayed if the fuel gauge goes be­
low the reserve marking when this funct ion is
switched on
g , After confirming this message, a
list of gas stations in the area is displayed . When
a gas station is se lected, route guidance from the
current vehicle position is calculated .
Notification when nearby*
The notification when nearby is switched off at
the factory.
The MM I notifies you whe n you are approaching
selected points of interest when this function is
switched on
g, You can a lso have a Notification
tone .
Presentation mode
The Presentation mode he lps yo u to effect ively
p lan a trip and follow the plann ed route without
mov ing the vehicle. You can use
Select starting
point
when you would like to calculate a route
starting from a location other than the vehicle
position, for example. Start
Presentation mode
to simulate route guidance.
Route criteria
A ppl ies to: ve hicles with navigation system
JI
Fig. 125 Possible rou te criter ia
.. Press the I NAV/MAPI but ton repeatedly until
the
Enter destination menu is displayed
<:!>page 134, fig. 122.
.. Se lect : right contro l button > Route criteria.
(;) HOV lanes/carpool lanes1
l: when the Avoid
function is switched on, HOV lanes or carpool
l) Hig h oc cupan cy veh icl e
Navigation
lanes are not included in the route calculation .
With
Allow , the MMI will guide you using HOV
and carpool lanes and it will indicate them.
@ Highways /@ Toll roads /@ Ferries : you can
select the
Avoid function to prevent the naviga­
tion system from calculating routes with high­
ways, toll roads or ferries, if possible.
Voice guidance
Applies to : vehicles wit h navigat ion syste m
.. Press the INAV/MAPI button repeatedly until
the
Enter destination menu is displayed
<:!>page 134, fig. 122 .
.. Select: r ight control button > Voice guidance .
Voice guidance :
voice guidance can be Complete
or Shortened . With the Traffic function, voice
guidance prompts are only given when there are
traff ic incidents on your route. When
Off is se­
lected, no voice guidance is given.
Voice guidance during phone call : voice guid­
ance during a phone call can be switched on or
off.
Entertainment fader : see¢ page 178.
Voice guidance volume : see¢ page 178.
Alternative routes
Applies to: vehicles wit h navigat ion system
Fi g. 126 Alte rnative routes disp lay
Requirement: a destinat ion must be entered and
the route guidance must be started.
.. Press the INAV/MAPI button repeatedly until
the
Enter dest ination menu is displayed
<:!>page 134, fig. 122.
141

Cl 00 .-< N r-­N .-< 0 r-­Vl 00
turn the left thumbwhee l on the mu ltifunction
steering wheel*
r=> page 18.
Turning th e cross hair s on /off
-Switching the crosshairs on : press the control
knob in the map view .
-Switching th e crossh airs off : press the I BACKI
button .
When the cros s h air s are s witched on r:!> fig. 12 7:
(D Orientation : th e map is either displayed as a
2D north up m ap or a 2D heading up map.
@ Scale : turn the control knob to the left or
right to decrease or increase the scale .
@ Zoom: when the Automatic zo om function is
switc hed on, an
"A" for "Automatic" is dis ­
p layed in the magnifying g lass.
© Crosshairs: move the crossha irs in the de­
sired direction us ing the MMI touch control
pad and set a po int on t he map as the desti­
n at ion or have info rmation about the fo cal
po int disp layed.
® Map content (points of interest, favorites) : if
there are mult iple POis in the immed iate v i­
cin ity, they will be shown stacked o n the
map .
@ Additional information on t he crosshai rs po ­
sition : if you move the crosshairs to a loca ­
tion on the map, avai lable information for
the current c rosshairs position is displayed.
Press the control knob to open destination
deta ils or to start route guidance . When the
crossha irs are turned off, the road being cur ­
rently d riven on is shown .
0 Disp lay o f an upcoming maneuver. If the re is
no upcoming maneuver, the distance and ca l­
culat ed arrival tim e to the destination/stop ­
over is displayed in this location.
@ Di sp lay of a better route . Seer:!> page 147 .
When the c rosshairs a re s witched o ff r:!> fig. 128 :
® If a turn arrow is displayed, a bar graph turns
on. The fewer bars are shown, th e shorter th e
d istance is unt il the turn .
l) O nly applie s to vehicl es withou t ca mer a-b as ed speed li mit
d is play .
Navigation
@ Speed limit display l): disp lay of the max i­
mum permitted speed on the expressways
and highways.
@ Road currently being driven on . When the ve­
hicle is stat iona ry, "off road" is displayed
here.
@ Vehicle location (@)
@ Display of active traffic information
(ION LINEI* or lTMC !)
@ Altitude disp lay (.d\)
@ Route information: var ious informa tion will
be displayed dur ing active route guidance
(for example, t he upcom ing maneuver in­
clud ing ca lculated distance and street
names). The d isplay a lso p rovides t raff ic in­
format io n or points of inte rest on the cur rent
route.
Map functions
Applies to : vehicles with navigation system
.. Press the !NAV /MAP I button repeatedly unti l
the map is displayed
r=> page 142, fig. 128.
.. Select: left control button > desired function.
Switch to d estin ation input
T he Enter de stin ation menu is d isp layed
r:!> page 134, fig. 1 22 .
Traffic messages
Current traffic information is disp layed in the In­
fota inme nt system display . See
r:!> page 145 .
Route list
The route list can o nly be disp layed when route
guidance is active and contains informat ion re ­
gard ing the route, the names of the streets and
the le ngth of the route sect ions. When traveling
o n highways, poss ible parking lots and rest areas
are show n, wh ich you can se lect as a stopove r.
POis along the route
Requirement: route guidance must be active .
Searching for points of interest a long your cur­
rent route See
r:!> page 13 7 .
143

Navigation Additional options on the map
A pp lies to: ve hicles w ith navigat ion system
.,. P ress t he I N AV/MAPI but ton repeate dly un til
t h e map is d is pla yed
¢page 14 2, fig. 12 8.
.,. Press t he righ t con tro l bu tton .
D epending on the f unct ion selected, the follow­
i n g op tions can also be se lec ted unde r the
Map
menu:
Cancel route guidance : see¢ page 139.
Map settings: see ¢ page 144.
Route criteria : see ¢page 14 1.
Voi ce guidance: see ¢ page 1 41.
Navigation settings : see ¢ page 140.
Online traffic data* : see ¢page 145 .
Show alternative routes: see ¢ page 14 1.
Parking along the route : parking options near
t he vehicle are disp laye d.
Save current position : you can save your current
ve hicle posi tion as a favor ite
¢ page 140 or save
it as a contact in t he
d ire cto ry¢ pag e 140.
Audi connect at this location ": allows yo u to
search fo r
City events or Weather at the entered
locat ion .
Country information: you ca n disp lay the appli ­
cab le urban and rura l speed lim its for any coun­
try/state . T his i nfo rmation w ill be automat ica lly
shown to you in the route i nfo rmat ion @
¢ pag e 142, fig . 128 w hen the speed lim it is ex ­
cee ded, if this funct ion is
acti vate d¢ page 145 .
Avoid route *: when route gu idance is act ive, the
calc ulated ro ute w ill avoid t he a rea yo u have
specif ied (max imum : 12 mi (20 km)), if possibl e.
Th e navigation sys te m cal cula tes a n alt er nat ive
ro ute. The rout e to be av o ide d that you h ave en ­
t ered applie s on ly to the cur rent route an d m ust
be set a gain, if neede d. The a reas yo u have se -
1> Provider at time of printing.
2> AUDI AG provi des access to services from third party pro ­
v iders. Pe rmanent ava ilability cann ot be guaran teed , be ­
cause that depe nds on th e thir d party provider.
144 l
ecte d to avoi d w ill appear wi th re d an d whit e
s h ading on the map .
Map settings
Applies to: vehicles wit h navigat ion syste m
.,. Press the I NAV/MAPI button repeatedly unti l
the map is displayed
¢ page 142, fig. 128.
.,. Select: r ight cont rol b utton> Map settings.
De pend ing o n the selected fu nction, t he follow ­
i ng settings can be selected :
Map colors
Day /Night :
the map i s disp laye d wit h a lig ht/
dar k backgroun d.
Automatic : when the ligh ts swi tch on, th e map
c ol ors swi tch from day to n ight.
Map display
Standard
<=> pag e 142, fig. 127 .
Google Earth *1
)2
) ¢ page 145, fig. 129 .
Traffic ¢page 14 5.
Map orientation
Destination :
th e map indica tes the des tination
and is or iented to t he nor th .
2D heading up map /2D north up map : the cur­
r ent vehicle pos ition is displayed . Th e map is ori­
en ted in the d irecti on of tr ave l o r to t he nor th.
3D map : when this function is switched on, the
cu rrent veh icle pos it io n is shown on a three-di­
mens iona l ma p and orien ted in t he d irec tion of
travel. At a sca le o f 62 mi ( 100 km) and la rge r,
t he m ap orie nta tion is to th e north.
Overview : the entire route from the vehicle pos i­
tion to the des tina tion or th e next s to p ove r is d is­
p layed on the m ap. The map scale depends on
t he le ngth of the ro ute an d ad ap ts au toma tically .
T he map is or iente d t o the north.
1111-

Navigation
Online traffic information
Applies to: ve hicles w ith navigation system and Audi connect
The MMI can receive real-time online traffic information about congestion, accidents, road construc­
tion and other incidents .
Fig . 130 Example : on line t raffic info rmat io n disp lay • wit hout better route
Req uirement : the requirements fo r Audi con nect
m ust be
met ~ page 124.
.,. Press the I NAV/MAPI button repeated ly until
the map is d isplayed .
" Select : rig ht contro l bu tton > Online traffic da­
ta > On ([;1).
"Se lect : left co ntrol button> Traff ic messages.
T he tra ffi c in fo rmat ion overv iew is shown.
D epending on vehicle equipment, the follow ing
i n fo rm ation may be show n in t he t raff ic informa­
tion
o ve rview ~ fig. 130:
(D A message will appear if the MMI calculates a
better route for the cu rrent route guidance .
M ore infor mation ca n be found unde r
~page 14 7.
@ The status line in the Infota inment display
indicates the reception of traffic information
(I T MC I or IONLI NEI).
@ The current selected traffic message is also
shown as a ma p preview i n the I nfota inment
sys tem disp lay.
© Color-coded markings along the route indi-
cate the traffic flow.
Traffic di splay
Green : traffic is flowing freely .
Yellow: stop-and-go traffic.
146
Red : congestion .
Shaded mark ings indicate the length of the area
with congestion.
Colored warning symbol s: there is a traffic i nci­
dent immediately ahead on the route .
Grayed out warning symbols : traffic incidents
that are not on your route .
Red warning symbols: all w arning sym bols w ill
be red w he n r out e g uidance is no t act ive.
The disp lay of colo red markings, warning sym­
bo ls, e tc. can be set in the
Map content menu
<;} page 14 5.
You can switch off the recept ion of on line traff ic
i nforma tion at any
t ime ~ page 146.
Switching the traffic map display on
For an optimum traffic information display:
I NAV/MAPI button> r ight control button > Map
settings > Map display > Traffic.
..,

Cl 00 ... N r-­N ... 0 r-­Vl 00
You can also display the o nline traffic info rma­
tion
in the sate llite map*1
) ¢ page 145 or the
standard map
¢ pag e 142, fig . 127
(D Tips
-Online traff ic information is not available in
Canada .
- Always read the chapter
~ page 131, About
Audi connect .
-Havi ng the Online tr affic data fu nction
switched on provides t he most accu rate re ­
ports of traffic situations as we ll as traffic
forecasting. Yo ur vehicle transmits and
processes its anonymous, encrypted posi ­
tion information at regular intervals to the
traffic data provider . If yo u do not want to
use this, you can switch off the
on line traf­
fic information
function at any time .
-The online traffic informat ion network is
curre ntly not ava ilable i n all countr ies, and
the coverage is not nat io nwide . For add i­
tiona l information, v is it www.aud iusa.com.
Traffic information (TMC)
Applies to: vehicles with navigation system
~ Press the I NAV /MAPI button repeated ly un til
the map is disp layed.
~ Se lect : left control button > Traffic me ssage s.
TMC t raffic mess ages are switched o n at the fac ­
tory.
Multip le traffic messages a re summarized in the
overview unde r th e correspondi ng street names
or h ighway names.
-Di spla ying all traffic messages for a street /
highwa y:
select and confirm the [ill symbol. A
l ist of a ll the traffic messages for the sele cted
st ree t/ hi ghway is displayed.
-Opening the detailed view of a tr affic me s­
s age :
if you se lect an ent ry from the list, the
t raff ic information will be shown as a map p re­
view ®¢
page 146, fig. 130 . Select and con-
l) AU DI AG prov ides acces s to serv ices from third pa rty pro ­
v iders . Pe rman ent availa bili ty c anno t be g uara nteed , be ­
c a use that dep ends on th e th ird party provid er.
Na vigation
firm a traff ic message to d isplay the details for
that message.
-Displ aying th e sele cted traffic me ssage on the
map :
select the right control button > Sh ow on
map .
-Displaying the ne xt traffic mes sage on the
map :
press the control knob .
Traffic information display
Colored warning symbol s:
traffic incidents o n
yo ur r oute are shown in the upper sect io n of the
li st and are sorted ac cording to d istance .
Warning symbol s with~: avo ided traff ic inci­
dents.
Grayed out warning s ymbol s: traffic incidents
that are not on your route . T hey are sorted ac­
cording to road type (expressway, h ighway, other
r oad), cou ntry and name.
Shaded markings indicate the length of the area
with congest ion .
(D Tips
Critical traffic information, such as war nings
abo ut wrong-way drivers, is a utomat ica lly dis ­
played . To hide t he traffic informat ion, press
the
IBACK ! button or the contro l knob .
-TMC traffic reports are not available in Can ­
ada . For more info rmat io n, p lease contact
S irius Canada.
Better route
Applies to: vehicles with navigation system
By receiving traffic information through TMC,
your MMI calculates a better route -if available -
and the possible time saved for the current route
guidance. You can decide yourself which route
you would like to use.
~ Press the ! NAV/MAPI button repeatedly unti l
t he map is displayed.
Requirement: route guidance must be active .
147

Navigation
If you r MMI has calculated a better route than
the current route guidance, the message
A better
route is available.
appears on the map along
with the time that may be saved. A better route
is indicated in the map view by the symbol
rS
c::;,pag e 142, fig. 127 .
Apply better route
- Press the right contro l button in the map view .
Or: select the left contro l button > Traffic mes·
sages.
The better route with the calcu lated ar­
rival time is displayed .
Troubleshooting
App lies to: ve hicles w ith navigation system
Problem Solution
-Select and confirm the better route. Or: select
and confirm
Details to display details about the
optimized route. You can zoom in or out on the
map using the MMI touch control pad. Require­
ment: there must be more than one optimized
route calculated. Press the control knob to
sw itch to the next route in the detailed view .
Closing the detailed view: press the I BACK I
button.
- After you have selected a better route, the
route w ill be recalculated.
Free text search: the desired des- The dest inat ion might not be entered in the navigation database.
ti nat ion cannot be found .
Or: check the spelling of the term that was searched . Check if the
desired country/state was selected for the free text search using
the
Country/state selection ¢page 135 or the option All coun-
tries/states.
148

System settings
delete the programmed voice training with the
Reset individual speech training function .
Factory settings
The follo wing funct ions can be reset to the facto­
ry default settings :
-Sound settings
- Radio
- Media settings
- Jukebox*
- Directory*
- Telephone *
- Bluetooth and Wi-Fi*
- Navigation settings *
- Navigation and online memory *
- Voice recognition system*
- Message settings *
-Apps*
-Tool tips
-Audi connect *
You can select the desired functions individually
or all at once with the option
Select all entries .
Select and confirm Restore factory settings.
(D Tips
-Make sure that not only t he settings were
deleted but also the stored data, if appl ica­
ble.
- Please note that the
voice recognit ion sys­
tem* is not available in Cabriolets that do
not have a factory- insta lled safety belt mi­
crophone .
174
Connection manager
Introduction
The connection manager gives you an overview
of your connected devices and their network sta ­
tus.
Settings Connection manager
I • Prima hone : M_Phone C,
t MyPhone ~
• Secondary phone : Not connected
• Data connect,on: Not connected
• MMI connect App: Not connected
• w,- F, aud ,o player: Not connected
Fig . 147 Co nnect ion manager
.,.. Select: !MENUI button> Settings > left control
button
> MMI settings > Connection manager.
.,.. Select and confirm a menu it em.
If a mobile device was already connected and you
select and co nfirm the corresponding menu item,
the device name and connect ion status are dis­
played under the menu item.
You can individually
Connect(~) or Disconnect
(0) a pa ired device.
Requirement:
- Th e vehicle m ust be stationary and the ignition
m ust be switched on .
- Th e Bluetooth settings will open on your mo­
bile device during the connection setup .
- Th e Bluetooth function and visibility of the MMI
c::> page 175 and mobile device must be switch­
ed on.
- Th e mobile device to be connected m ust not be
connected to any other B luetooth dev ice .
Primary phone
App lies to: vehicles wi th telepho ne
- Connect new device: search for and connect a
cell phone.
- List of devices already paired: select your cell
phone from the list of all the devices that are
already paired.

System settings
Ringtone volume: you can adjust the volume of
the selected ringtone by turning the contro l
knob.
Message volume: you can adjust the volume of
the notification for an incoming text message by
turning the control knob.
Microphone input level : you can adjust the vol­
ume during a phone call by turning the control
knob.
Navigation
A pp lies to: ve hicles w ith navigation system
Voice guidance: see¢ page 141, Voice guidance.
Voice guidance during phone call: see
¢ page 141, Voice guidance.
Voice guidance volume: you can adjust the voice
gu idance volume during active route guidance by
turn ing the control knob.
Entertainment fader : the volume of audio play ­
back can be temporarily lowered when the park­
ing system or voice guidance is active.
Voice recognition system
App lies to: ve hicles w ith vo ice recogni tion sys te m
Short dialog : prompts in a shorte r format can be
switched on or o ff.
Speech dialog system volume: you can adjust
the volume of the prompts by turning the control
knob.
Parking aid*
You can adjust the signal tone volume by turning
the control knob.
-Adjusting the Front volume: select and con­
firm
High , Medium or Low .
- Adjusting
the Rear volume: select and confirm
High, Medium or Low .
MMI touch volume*
You can adjust the vo lume of the prompts for the
MMI to uch* by turning the contro l knob.
Audi Heartbeat
You can adjust the volume of Aud i Heartbeat by
t ur nin g the control knob.
178
(D Tips
Please note that the voice recognition sys­
tem* is not available in Cabr io lets t hat do not
have a factory-installed safety belt micro­
phone.
Restarting the MMI
(Reset)
Fig. 149 Button co mbin ation to res tart the syste m
.. Briefly press the control knob and both buttons
at the same time to immediately open the
menu
upward ¢ fig. 149.
Software License
information
Information on MMI software and licensing
agreements
- Select: ~
I M _ E_N_ U~ I button> Settings > left control
button >
System maintenance > Version infor­
mation.
- Or : online at www .audiusa .com/software info .
Information on instrument cluster software and
licensing agreements
Press the reset button 10.01 twice within five sec ­
onds after switching the ignition on.