2018 AUDI Q7 tires

Cl a:, ...... N
" N ...... 0
0
::r ' For example: Tread wear 200, Traction AA, Tem­
perature
A.
All passenger car tires must conform to Federal
Safety Requirements in addition to these grades.
Tread wear
The tread wear grade is a comparative rating
based on the wear rate of the tire when tested
under controlled conditions on a specified gov­
ernment test course.
For example, a tire graded 150 would wear one
and one ha lf (1 1/2) times as well on the govern­
ment course as a tire graded 100.
The relative performance of tires depends upon
the actual conditions of their use, however, and
may depart significant ly from the norm due to
variations in driving habits, service practices and
differences in road characteristics and climate.
Traction
The traction grades, from highest to lowest, are
AA, A, B and
C. Those grades represent the tire's
ability to stop on wet pavement as measured un­
der controlled conditions on specified govern­
ment test surfaces of asphalt and concrete . A tire
marked C may have poor traction performance
¢ &, .
Temperature
The temperature grades are A (the highest), B,
and C, representing the tire's resistance to the
generation of heat and its ability to dissipate
heat when tested under controlled conditions on
a specified indoor laboratory test wheel.
Sustained high temperature can cause the mate­
rial of the tire to degenerate and reduce tire life,
and excessive temperature can lead to sudden
tire failure¢ &,.
The grade C corresponds to a level of perform­
ance which all passenger car tires must meet un­
der the Federal Motor Vehicle Safety Standard
No. 109. Grades Band A represent higher levels
of performance on the laboratory test wheel than
the minimum required by law.
Wheels
A WARNING
--
The traction grade assigned to this tire is
based on straight-ahead braking traction
tests, and does not include acceleration, cor­
nering, hydroplaning or peak traction charac­
teristics.
A WARNING
The temperature grade for this tire is estab­
lished for a tire that is properly inflated and
not overloaded. Excessive speed, underinfla­
tion, or excessive loading, either separately or
in combination, can cause heat buildup and
possible tire failure.
A WARNING
-
--
Temperature grades apply to tires that are
properly inflated and not over or underinflat­
ed.
Tire pressure monitoring system
ill
General notes
Each tire, including the spare (if provided),
should be checked monthly when cold and inflat­
ed to the inflation pressure recommended by the
vehicle manufacturer on the vehicle placard or
tire inflation pressure label. (If your vehicle has
tires of a different size than the size ind icated on
the vehicle placard or tire inflation pressure la­
bel, you should determine the proper tire infla­
tion pressure for those tires).
As an added safety feature, your vehicle has been
equipped with a tire pressure monitoring system
(TPMS) that illuminates a low tire pressure tell­
tale when one or more of your tires is significant­ ly under -inflated. Accordingly, when the low tire
pressure telltale illuminates, you should stop and
check your tires as soon as possible, and inflate
them to the proper pressure. Driving on a signifi­ cantly under-inflated tire causes the tire to over­
heat and can lead to tire failure . Under-inflation
also reduces fue l efficiency and tire tread life,
and may affect the vehicle 's handling and stop-
ping ability. .,.
347

Wheels
Please note that the TPMS is not a substitute for
proper tire maintenance, and it is the driver's re­
sponsibility to maintain correct tire pressure,
even if under-inflation has not reached the level
to trigger illumination of the TPMS low tire pres­
sure telltale.
Your vehicle has also been equipped with a TPMS
malfunction indicator to indicate when the sys­
tem is not operating properly. The TPMS mal­
function indicator is combined with the low tire pressure telltale. When the system detects a
malfunction, the telltale will flash for approxi­
mately one minute and then remain continuously
illuminated. This sequence will continue upon
subsequent vehicle start-ups as long as the mal­
function exists.
When the malfunction indicator is illuminated,
the system may not be able to detect or signal
low tire pressure as intended. TPMS malfunctions
may occur for a variety of reasons, including the
installation of replacement or alternate tires or
wheels on the vehicle that prevent the TPMS
from functioning properly . Always check the
TPMS malfunction telltale after replacing one or
more tires or wheels on your vehicle to ensure
that the replacement or alternate tires and
wheels allow the TPMS to continue to function
properly.
If the tire pressure monitoring indicator
appears
Applies to: vehicles with Tire Pressure Monitoring System in­
dic ato r
The tire pressure indicator in the instrument
cluster informs you if the tire pressure is too low
or if there is a system malfunction.
Using the ABS sensors, the tire pressure monitor ­
ing system compares the tire tread circumfer­
ence and vibration characteristics of the individu­
al tires . If the pressure changes in one or more
tires, this is indicated in the instrument cluster
display with an indicator light
RI] and a message.
If only one tire is affected , the location of that
tire will be indicated.
The tire pressures must be stored in the Infotain­
ment system again each time the pressures
348
change (switching between partial and full load
pressure) or after changing or replacing a tire on
your vehicle ~
page 349. The tire pressure moni­
toring system only monitors the tire pressure you have stored. Refer to the tire pressure label for
the recommended tire pressure for your vehicle
~ page 340, fig . 272.
Tire tread circumference and vibration character­
istics can change and cause a tire pressure warn­
ing if:
- the tire pressure in one or more tires is too low
- the tires have structural damage
- the tire was replaced or the tire pressure was
changed and it was not stored
~ page 349
- tires that are only partially used are replaced
with new tires
Indicator lights
RI] -loss of pressure in at least one tire~,& .
Check the tires and replace or repair if necessary.
Check/correct the pressures of all four tires and
store the pressure again in the Infotainment sys­
tem
~ page 349.
m (Tire Pressure Monitoring System) Tire
pressure: malfunction! See owner's manual.
If
m appears after switching the ignition on or
while driving and the
RI] indicator light in the in­
strument cluster blinks for approximately one
minute and then stays on, there is system mal­
function. Try to store the correct tire pressures
~ page 349. In some cases, you must drive for
several minutes after storing the pressures until
the indicator light turns off . If the indicator light
does turn off or turns on again after a short peri­
od of time, drive to an authorized Audi dealer or
authorized Audi Service Facility immediately to
have the malfunction corrected.
& WARNING
- If the tire pressure indicator appears in the
display, reduce your speed immediately and
avoid any hard steering or braking maneu­
vers. Stop as soon as possible and check the
tires and their pressure.

-The driver is responsib le for maintaining the
correct tire pressure. You must c heck the
t ire pressure regu larly.
- Under certa in conditions (s uch as a sporty
dr iv ing style, winter cond itions o r unpaved
roads), the tire p ressure monitoring system
indicator may be de layed .
(D Tips
-The t ire press ure monitoring system can al­
so stop work ing when there is an ESC mal­
funct ion.
- Using snow chains may result in a system
malfunction.
- The t ire press ure monitoring system in your
A udi was calib rated with "A udi Orig inal
Tires"
<=)page 337. Using these t ires is rec­
omme nded .
Storing tire pressures
Applies to: vehicles with Tire Pressure Monitoring System in­
dicator
If the tire pressure changes or a tire is replaced,
it must be confirmed in the Infotainment sys ­
tem.
~ Make s ure before storing that the tire pressures
of a ll fou r tires meet the specified values and
are adapted to the load
Q page 340 .
~ Switch the ign ition on.
~ Se lect in the Infotainment system: ! MENUI but­
ton
> Vehicle > Service & checks > Tire pres­
sure monitoring > Store tire pressur e> Yes,
store now .
(D Tips
Do not store the tire press ures if snow chains
are insta lled.
Run-flat ti res
Applies to: vehicles with run-flat tires
A run-flat tire helps to maintain vehicle mobility
when there is a loss of pressure .
Cl ~ Run-flat t ires have re inforced sidewalls that pro-
~ tect the t i re if there is a loss of press ure. N ,-1 0
0
::r ' Wheels
If the t ire pressure monitoring system indicates a
l oss of pressure in one or severa l tires, yo u can
contin ue driving on run -flat tires fo r at least 20
miles (30 km). Drive to an authorized Audi dealer
or authorized Aud i Serv ice Facility immediately to
have the problem corrected .
Continuing to drive on run-flat tires is n o
longer possible if
- there is visible damage to the tires, such as
cracks in the sidewalls .
- strong vibrat ions are felt w hile driving, or the
tire beg ins to smoke due to a strong build-up of
heat .
- the t ire was heavi ly damaged, for example in an
accident There is a r isk that parts of the tire
tread will detach and damage important ve hi­
cle components .
- the E lectron ic Stab ilizat ion Control (ESC) is not
work ing or is cont inuously r unning .
- the t ire pressure monitoring system is not
work ing .
If it is no longer poss ible to continue driving de­
spite hav ing run-flat tires, see an author ized Audi
dealer or author ized Audi Service Fac ility for as­
s istance.
A WARNING
-
R un-f lat t ires may only be used on vehicles
that we re equipped with them at the fa ctory.
- The vehicle must have suspens ion designed
for run-flat tires and a facto ry-installed tire
p ress ure mo nitor ing syste m.
- I nco rrect use of r un-f lat t ires can lead to ve­
h icl e damage o r accidents. Contact an au­
thor ized A udi dealer or au thori zed A udi
Serv ice Facili ty to lear n if r un-f la t tir es may
be used on you r vehicle an d if so, which
ones.
- If r un-fla t ti re s are used, they m ust be in ­
stalled on all fo ur whee ls. Mix ing ti re types
is not permitted.
- If yo u have to drive when the tire press ure is
too low or there is no tire press ure, note the
following : .,..
349

Wheels
-Do not dr ive faste r than 50 mph (80 km/
h) because this increases the risk of an ac­
cident. Observe any laws specific to the
country where yo u are driv ing.
- Avoid full-th rottle accele ration, heavy
braking, and fast cornering, because this
increases the r isk of an accident .
- The vehicle may become more difficult to
control.
- See an autho rized Aud i deale r or a uthor­
ized Audi Service Fac ility for assistance if
the t ire is too heavily damaged.
- Have the faulty tires replaced and the rims
checked fo r damage by an author ized A udi
dealer or author ized Audi Service Facil ity.
- The driver is responsib le for the vehicle, fo r
correcting the t ire pressure and for rep lac­
ing faulty parts. Therefore, always adjus t
yo ur driv ing to the g iven s ituation .
(D Tips
-Audi Orig inal run-flat tires can be identified
by the "AOE" labeling on the tire sidewall.
- You can use the tire mob ility k it*
c:> page 357 on run-flat ti res.
350

Cl a:, ...... N
" N ...... 0
0
::r ' Care and cleaning
General information
Regular, proper ca re helps to maintain your ve hi­
cle's value. It can a lso be a requirement when
submitting warranty claims fo r cor rosion damage
and pa int defects on the body.
The requ ired cleaning and care p roducts can be
obtained from an authorized Audi dea le r or au ­
thor iz ed Se rvice Facility . Read and follow the in ­
structions for use on the packaging .
A WARNING
-Us ing clea ning and ca re products inco rrectly
can be dangero us to your hea lth .
- Always store clean ing and ca re prod ucts out
of reach of chi ldren to reduce the r isk of po i­
soning .
@ For the sake of the environment
- Prefe rab ly purchase env ironmenta lly-friend­
l y cleaning prod ucts.
- Do not d ispose o f leftove r clea ning and ca re
p roducts with house hold t rash.
Car washes
T he longer that deposits s uch as insects, bird
d roppings, tree sap or road salt remain on the ve­
h icle, the more the surface can be damaged. High
temperatures such as those ca used by sun light
in crease the damag ing effect .
Before washing, r inse off heavy depos its with
p le nty of water.
St ubborn deposits s uch as bird d roppings or tree
sap are best removed with plenty of wate r and a
m icr ofibe r cloth.
A lso, wash t he un derside of yo ur vehicle once
road sa lt stops being used for the seaso n.
Pressure washers
When washing your ve hicle wit h a pressu re wash­
e r, al ways fo llow the operating instr uctions pro ­
v ided wi th t he p ress ure washer. This is espe cially
i mportant in rega rd to the p ressure and sp raying
d istance . Do not aim the sp ray directly at the
Care and cleaning
seals on the side w indows, doo rs, lid s or the s un ­
r oof * or at tires, r ubber hoses, insulat ing mater i­
al, sensors* or camera lenses* . Keep a distance of
at least 16 in (40 cm).
D o not remove snow and ice with a p ressure
washe r.
Never use cone nozz les o r high press ure no zzles .
T he wate r temperatu re mus t not be above 140 °F
(60 °() .
Automatic car washe s
Spray off the vehicle befo re washing.
Make s ure that the w indows and roo f* are closed
and the windsh ie ld wipers are off . Follow instruc ­
tions from the car wash ope rato r, especially if
the re are accesso ries attached to your vehicle.
If possible, use car washes that do not have
brushes .
Washing by hand
Clean the ve hicle starting from t he top and wor k­
in g down using a soft sponge o r clea ning br ush.
U se solven t-free cleaning p ro duc ts.
Washing vehicles with matte finish paint by
hand
To avo id da mag ing the p aint w hen w ashi ng, fi rs t
r emove dust and large p art icl es from you r vehi ­
cl e. Insects, grease spots and finger prints are
best removed w ith a s pecial cleane r fo r matte
f inish paint.
Apply t he p rodu ct using a microf iber cloth . To
avo id damag ing t he pa in t surface, do no t use too
much pressure.
Rinse t he ve hicl e thoroug hly w ith w ate r. T hen
cl ea n usi ng a neutra l shampoo an d a soft mi cro­
f iber cloth .
R inse t he ve hicle thoroug hly aga in and let it air
dry. Remove any wate r residue using a chamois.
,&. WARNING
--
- Only was h the veh icle w hen the ig nition i s
off and follow t he i nstr uctions from the car
351

Emergency assistance
See an authorized Audi dealer or authorized Audi
Service Facility for assistance in these situations.
A WARNING
-Please note that the tire mob ility kit cannot
be used in all situations, and that it may on­
ly be used temporarily.
- The tire sealant must not come in contact with skin, eyes, or clothes.
- If tire sealant gets in your eyes or on your
skin, thoroughly rinse the affected area im­
mediately with clean water.
- Do not inhale the fumes .
- If you swallow any of the tire sealant, thor-
oughly rinse your mouth immediately and
drink a lot of water. Do not induce vomiting .
Seek medical attention immediately.
- Change your clothes immediately if they get
tire sealant on them.
- If an allergic reaction occurs, seek immedi­
ate medical attention .
- Keep the tire sealant away from children .
(D Tips
-If sealant leaks, allow it to dry in place. You
can then peel it
off like a sticker.
- Note the expiration date on the sealant bot­
tle . Replace the tire sealant at an author­
iz ed Audi dealer or authorized Audi Service
Facility.
- Radio reception can be interrupted when
operating the compressor.
- Obey all laws.
Repairing tires
Fig. 274 Components of the tire mobility kit
358
~
"' 0
> u.
m
Fig. 275 Tire mobil ity kit connection
Requirement: the tire mobility kit must be laid
out and ready for use¢
page 357.
Installing the tire mobility kit
"" Open the cover @on the compressor
¢fig. 274 .
"' a, N 0
> u. m
""Remove the connector © and pressure hose®
with pressure gauge from the housing.
""Install the compressor pressure hose® onto
the flange @ on the tir e sealant bottle@.
"" Insert the sealant bottle with the flange at the
bottom into the opening @ on the compressor
cover.
"" Remove the valve cap from the faulty tire.
"" Install the filler hose@on the valve
(J)
¢fig. 275 .
"" Connect the plug©¢ fig. 2 74 to an outlet in
the vehicle .
"" Switch the ignition on.
Inflating a tire
""Move the switch @ ¢fig . 275 on the compres­
sor into position
I.
"" Inflate the tire to between 29 psi (200 kPA)
and 36 psi (250 kPA) and read the pressure on
the gauge.
"" If this tire pressure is not reached, remove the
filler hose . Drive slowly approximately 33 feet
( 1 0 m) forward or in reverse so that the sealant
can be distributed in the tire. Pump up the tire
aga in ¢ .&, .
A WARNING
-Read and follow the manufacturer's safety
precautions on the compressor and in the
instructions on the bottle of sealant.

Emergency assistance
vehicle tool kit) ¢ fig. 280 and place it on a
clean surface.
• Then install the alignment pin (from the vehicle
tool kit) by hand into the empty wheel bolt hole
¢fig. 2a11>.
• Remove the rest of the wheel bolts .
• Remove the wheel ¢@ . The al ignment pi n re-
mains in the hole while doing this .
Install a wheel
Read the direct ions on c> page 362 when instal­
ling unid irectional tires.
• Slide the wheel on over the alignment pin¢@ .
• Install the wheel bolts and tighten gently using
the hex socket.
• Remove the alignment pin and also tighten the
remaining wheel bolt.
• Carefully lower the vehicle using the vehicle
jack* .
• Tighte n the wheel bolts in a diagona l pattern
u sin g the wheel wrench.
The whee l bolts must be clean and loosen/tight­
en easi ly. Check the contact su rfaces for the
wheel and hub . Contaminants on these surfaces
m ust be removed before installing the wheel.
A WARNING
Never use the hex socket in the screwdriver
hand le or the hex socket wrench with the
ratchet to loosen or tighten the wheel bolts.
You will not attain the required tightening
specification, which wi ll increase the risk of an
accident .
@ Note
When removing or installing the whee l, the
r im could hit the brake rotor and damage the
rotor. Work carefu lly and have a second per­
son help you.
-
1
> A pp lies to vehicles with cer amic br ake rot ors*: use a sec ­
on d alignment pin * (fro m th e ve hicle t ool kit) for th e low ­
e st hole ac co rding t o the steps de scribed for the first
al ig nm ent pin.
362
(D Tips
-When mounting tires with unidirectional
tread design
make sure the tread pattern is
pointed the right way
c> page 362.
-Th e wheel bolts should be clean and easy to
turn. Check for dirt and corrosion on the
mating surfaces of both the wheel and the
hub. Remove all dirt from these surfaces be­
fore remounting the wheel.
Unidirectional tires
A un idirectional tire profi le is identified by arrows
that point in the running direct ion on the tire
s idewa ll. You must always adhere to the speci­
fied running direction. This is necessary ensure
t h e tire's optimum performance in regard to ad­
hesion, running noise, friction and hydroplaning .
To benefit fully from the advantages of the uni­
directional tire design, you should rep lace fau lty
tires as soon as possible and restore the correct
running direction on all of the tires.
Finishing
• Reinstall the caps on the wheel bolts if neces­
sary.
• Store the veh icle tool k it in its designated
place .
• Store the replaced tire securely in the luggage
compa rtment
¢page 257.
• Check the tire pressure on the insta lled wheel
as soon as possible.
• Cor rect the tire pressure and store it in the In­
fotainment system ¢
page 349.
• The wheel bolt tightening specification must be
120 ft lbs (160 Nm). Check it as soon as possi­
ble with a torque wrench. Drive carefully until
then .
• Have the faulty wheel replaced as quickly as
possible .

Cl a:, ...... N
" N ,-1 0
0
::r ' (D Tips
-If you notice t hat the wheel bolts are cor­
r oded and diffic ult to turn w hile chan gin g a
tire, they should be rep laced befo re yo u
chec k th e ti ghtening torque.
- D rive a t reduced speed until you have the
ti ghtening torques c hecked.
Notes on wheel changing
P lease read the i nfo rmation r=> page 33 7 if you
a re go ing to use a replaceme nt tire which i s dif­
fe rent from the tires on you r ve hicl e.
Afte r you change a t ire:
- Check the tire pressure on the replacement
tire immediately after installation.
- Have the wheel bolt tightening torque
checked with a torque wrench as soon as pos­
sible by your authorized Audi dealer or quali­
fied workshop.
- With steel and alloy wheel rims , the wheel
bolts a re correctly tightened at a torque of
120 ft lbs (160 Nm) .
- If you notice that the wheel bolts are corroded
and difficult to turn while changing a tire,
they should be replaced before you check the
tightening torque.
- Replace the flat tire with a new one and have
it installed on your vehicle as soon as possi­
ble. Remount the wheel cover.
Until then, drive with extra care and at reduced
speeds.
A WARNING
- If you ar e going to equip your ve hicle w it h
t ir es o r rims w hich differ fr om thos e which
w ere factory ins talled , th en b e sur e to read
t h e info rm at ion
<=> page 337 .
-Always ma ke sur e the damaged wh eel or
e ven a flat tir e an d th e jack* and tool kit ar e
p ro pe rly se cured i n the luggage com part ­
me nt a nd are n ot lo ose in the p assenger
c omp artmen t.
- I n an a ccide nt or sud den mane uve r they
co uld fly forwar d, injuring anyone in t he ve­
hicle .
-
Emergency assistance
-Always s tore damaged wheel, jac k* and
too ls sec urely in the lug gage com partment .
Oth erwise, in an acc ident or sud den maneu ­
v e r th ey could fly forward, causing in jury to
pass engers in t he v ehicle .
363