2018 AUDI Q5 headlight

u co ..... N ,..._
N ..... 0 <( 0 00
Certain instrument cluster content can also be
displayed in the head-up display*
¢ page 18.
A WARNING
Do not assume the roads are free of ice based
on the outside temperature display . Be aware
that there may be ice on roads even when the
outside temperature is around 41 °F (+5 °C)
and that ice can increase the risk of accidents .
(D Tips
-Depending on vehicle equipment, the in­
strument illumination (needles and gauges) may turn on when the lights are off and the
ignition is switched on . The illumination for
the gauges reduces automatically and even­
tually turns off as brightness outside in­
creases. This function reminds the driver to
turn the low beams on at the appropriate
time.
- You can select the units used for tempera­
ture, speed and other measurements in the
Infotainment
system ¢ page 245.
-If your vehicle is stationary or if you are driv­
ing at very low speeds, the temperature dis­
played may be slightly higher than the ac­
tual temperature outside due to the heat ra­
diating from the engine.
- At temperatures below 41 °F (+5 °C), a
snowflake symbol appears in front of the
temperature
display ¢,&. .
Coolant temperature indicator
The coolant temperature display @¢ page 10,
fig . 3
or ¢ page 10, fig . 4 only functions when
the ignition is switched on. To prevent engine
damage, please observe the following notes
about the temperature ranges.
Cold range
If only the LEDs at the bottom of the gauge turn
on, the engine has not reached operating tem­ perature yet . Avoid high engine speeds, full ac­
celeration and heavy engine loads.
Cockpit overview
Normal range
The engine has reached its operating tempera­
ture once the LEDs up to the center of the gauge
turn on. If
the. indicator light in the instru­
ment cluster display turns on, the coolant tem­
perature is too
high ¢ page 23.
@ Note
-Auxiliary headlights and other accessories in
front of the cooling-air intake impair the
cooling effect of the coolant. This increases
the risk of the engine overheating during
high outside temperatures and heavy en­
gine load .
- The front spoiler also helps to distribute
cooling air correctly while driving. If the
spoiler is damaged, the cooling effect will
be impaired and the risk of the engine over­
heating will increase. See an authorized
Audi dealer or authorized Audi Service Fa­
cility for assistance.
Tachometer
The tachometer displays the engine speed in rev­
olutions per minute (RPM).
The beginning of the red zone in the tachometer
indicates the maximum permissible engine speed
for all gears once the engine has been broken in
and when it is warmed up to operating tempera­
ture. Before reaching this zone, you should shift
into the next highest gear, select the "D/S" selec­
tor lever position, or remove your foot from the
acce lerato r pedal.
@ Note
The needle in the tachometer @¢ page 10,
fig. 3
or ¢ page 10, fig. 4 may only be in the
red area of the gauge for a short time or there
is a risk of engine damage . The location where
the red zone begins varies depending on the
engine.
@) For the sake of the environment
Upshifting early helps you to save fuel and re­
duces operating noise.
11

u co ..... N
range and you have released the accelerator ped ­
a l once .
I f t he engine speed lim itation was act ivated by
an eng ine contro l m alfu nction, the
II ind icator
light also turns on. Make su re the engine speed
does not go above the speed displayed, for exam ­
p le when downshifting. Drive to an autho rized
Aud i dealer or authorized Aud i Serv ice Facility im ­
mediately to have the malfunction corrected.
--... Engine oil sensor
II Oil l evel sy stem: malfunction! Pleas e con­
tact Service
The sensor to check the engine oil level has
fa iled. Drive to an authorized Aud i dealer or au­
thor ized Audi Service Fac ility immed iate ly to have
the malfunct ion co rrected.
• O il le vel sensor : o il change necessary. Please
c ontact Service
F ue l has entered the engine oi l as a resu lt of fre­
q uent short dr ives. Avoid high engine speeds, full
acceleration and heavy engine loads. Dr ive to an
author ized Audi dealer or author ized Audi Service
Fac il ity immediately to have the oil changed .
• Oil pressure senso r: malfunction! Plea se
contact Service
There is a malfunction in the oil pressure sensor .
Drive to an authorized Audi dea ler or a uthorized
Aud i Service Facility immediately to have the
malfunct ion corrected.
f Engine warm-up request
0 Plea se driv e to warm up eng ine
F ue l has entered the eng ine oi l, either from low
outside temperatures o r frequent short drives.
Drive unt il the engine is warm so that the fue l in
the eng ine oi l wi ll evaporate. Avoid high engine
speeds, full accelerating and heavy eng ine loads
when doing this.
Bil Tank system
I"-
~ 1111 Pl ease r efu el 0 <( 0 00
Coc kpit o ver view
If the indicato r light turns on for the first time
and the message appears, there are about 2 .1
gallons (8 liters) of fuel left in the tank .
fiD Please refuel immediately
If the indicato r light turns on the message ap­
pears, the fuel ta nk is a lmost empty. Refue l the
vehicle immedia tely.
1111 Tank system: malfunction! Plea se contact
Service
There is a ma lfunction in the fuel tank system.
Drive to an authorized Audi dealer or authorized
Audi Service Facility immediate ly to have the
malfunction corrected.
(D Tips
F o r more information on f ueli ng, see
r=;, page 311 .
~ Washer fluid level
m Please add washer fluid
Fill the was her fluid for the windshie ld washer
system and the headlight washer system* when
the ignit ion is switched
off ¢ page 323 .
! Windshield wipers
$ vVindshield wipers: malfunction! Please con­
tact Service
The re is a ma lfunction w ith the windshield wip­
ers.
Drive to an authori zed A udi dealer or authorized
Audi Service Facility immediate ly to have the
malfunction corrected.
~ Driver's door
II D riv er 's door : malfunction! Shift to P befo re
lea ving veh icle. Se e owner's manual
There is a ma lfunction in the driver's door. Se lect
the "P" selector lever posit ion to secure the vehi-
c le.
~
27

Cockpit overv ie w
Drive to an authorized Audi dea le r or a uth orized
Audi Service Facility immediately to have the
malfunct ion corrected .
·:q'): · Bulb failure indicator
If the II indicator light turns on, a bu lb has
fa iled. The message ind icates the location of the
bulb. Replace the bulb immediately .
Vehicle lights: malfunction! Plea se cont act
Service
There is a malfunction in the head lights or the
lig ht switch. Drive to an autho rized A udi dealer or
author ized Audi Service Facility immed iate ly to
have the ma lfunction corrected.
A WARNING
- light bu lbs are under pressure and can ex­
plode when bulbs are replaced, which in­
c reases the risk of injury.
- With HID headlights (xenon headlights), the high-voltage componen t must be handled
correctly. Othe rw ise, there is a risk of fata l
lnJUry.
i,(D Dynamic headlight range control
II Headlight rang e control : malfun ction! See
owner 's manual
There is a malfunc tion in the headl ight range
cont rol system, wh ich may ca use g la re fo r othe r
d rivers.
Drive to an authorized Aud i dea ler or aut horized
Aud i Serv ice Facility immediately to have t he
malfunct io n corrected.
~O Audi adaptive light
App lies to: ve hicles w ith Audi adaptive light
Ill Audi adaptive light : malfunction! See own­
er' s manual
-
Adapt ive light is not work ing . The headlights st ill
f un ction.
Drive to an authorized Aud i dea ler or a uthorized
Aud i Serv ice Facility immediately to have the
malfunct io n corrected.
28
@. D Light/rain sensor
II Automa tic h eadlight s: malfun ction! See
owner' s manual
l;I Automat ic wipers: malfunction ! See owner's
manual
The light/rain sensor is malfunctioning.
The low beams remain switched on at all times
for safety reasons when the light switch is in the
AUTO position. However, yo u can cont inue to
turn the lig hts on and
off using the light switch.
You can sti ll contro l all functions that are inde ­
pendent of t he rain senso r thr ough the wind­
shield wipe r leve r.
D rive to an authorized Audi dealer or authorized
Audi Service Fac ility immed iate ly to have the
malfunction corrected .
g Suspension control
Applies to : vehicles wit h suspension control
R Suspension : malfunction! You may continue
driving
There is a suspension control malfunction.
Drive to an authorized A udi dealer or authorized
Audi Service Facility immed iate ly to have the
malfunction corrected .
~: All wheel drive/sport differential
App lies to: vehicles wit h all w hee l drive/s port diffe re n tial
Ill All-wheel drive : malfunction! You may con­
tinue driv ing. Please contact Service
Ill Sport d ifferential: malfunct ion! Please con­
tact Service
There is a ma lf u nction.
D rive to an au thor ized A udi d ealer or au thori ze d
Audi Se rvice Facility immediate ly to have the
malfunction corrected.
Ill All -wheel driv e overheating . Please adapt
driving style . See owner's manual
Ill Sport differential: temperature too high .
Pl ease adapt driving style

Lights and Vision
Exterior Lighting
Switching the lights on and off
--- ----~-----'~
i
Fig. 37 Instrument p anel: l ig ht switc h with buttons
Light switch ·'!:! ·
Turn the light sw itch to the corresponding posi­
tion when the ignition is switched on.
:oo: and the
selected pos ition turn on (except pos ition 0).
0 -The daytime r unning lights automat ica lly t urn
on. In vehicles for certain markets, you can
switch the automatic daytime running lights on
and off in the Infotainment system*.
AUTO
-T he headlights automatically adapt to the
surrounding brightness.
: oo : -Parking lights
io -Low beam headlights
Buttons
When you turn the light switch to the AUTO or
low beam headlight pos ition
io, you can activate
the following functions:
~ o -A ll-weather lights. The headlights automati ­
cally adjust so that there wi ll be less glare, for
examp le when the road surface is wet.
O t -Rear fog lights
Automatic headlight range control system
Your veh icle is equipped with an automatic head ­
l ight range contro l system that re duces g lare fo r
oncoming traffic i f the vehicle load c hanges. The
~ headlight range ad justs automatica lly . ..... N r-­N .....
~ 0 co
Lights and V ision
Audi adaptive light
Appl ies to: vehicles wit h adaptive light
Adaptive ligh t provides better visibili ty whe n it i s
dark by adapting the lights to the road conditions
based on speed , such as on e xpressways, rura l
roads, at intersections, and in c urves. The adap­
t ive light only functions when the light sw itch is
i n the AUTO position .
A WARNING
--Automatic headlights* are on ly intended to
assist the driver. They do not relieve the
driver of responsibil ity to check the head­
lights and to t urn t hem on manua lly based
on t he curren t ligh t and v is ibility condition s.
For examp le, fog canno t be detec ted by the
light sensors. So always switch on the low
beams under these weather co nditions and
when driv ing in the da rk
io .
- To prevent glare for traffic behind yo ur vehi ­
cle, the rear fog lights should only be turned
on in accordance with traff ic regulat ions.
- Always observe legal regulations when
us­
ing the lighting systems desc ribed .
(D Tips
- The lig ht sensor for the automat ic he ad ­
lights * is in the rearview mir ror mount. Do
not p lace any st ickers in this area on the
windshield.
- A warning tone will sound if you open the door when the exte rior lights a re switched
on .
- Only t he front headlights turn on when t he
daytime running lights are switched on *. In
vehicles in certain markets, the tail lights
w ill also turn on .
- In cool or damp weather, the inside of the
head lights, turn signa ls and tail lights can
fog over due to the temperature diffe rence
between the inside and outside . They will
clear shortly afte r swi tching them on . This
does not aff ect the service life of the light­
mg.
45

Lights and Vision
Turn signal and high beam lever
The lever operates the turn signals, the high
beams and the headlight flasher .
Fig. 38 Turn sig nal and high beam lever
Turn signals¢ Q
N
0 0
> u.. a,
The turn signals activate when you move the lev­
er into a turn signal position when the ignition is
switched on.
@ -Right turn signal
@-Left turn signal
The turn signal blinks three times if you just tap
the lever.
High beams and headlight flasher ~D
Move the lever to the corresponding position:
@ -High beams on (vehicles with high beam as­
sistant*¢ page 46)
©-High beams off or headlight flasher
The
II indicator light in the instrument cluster
turns on .
A WARNING
High beams can cause glare for other drivers,
wh ich increases the risk of an accident. For
this reason, only use the high beams or the
headlight flasher when they will not create
glare for other drivers.
46
High beam assistant
App lies to : vehicles with high beam ass istant
The high beam assistant automatically turns the
high beams on or off depending on the surround­
ing conditions .
A camera on the rearview mirror mount can de­
tect light sources from other road users. The high
beams switch on or off automatically depending
on the posit ion of vehicles driving ahead and on­
coming vehicles, the vehicle speed and other en­
vironmen tal and traffic conditions.
Activating high beam assistant
Requirement: the light sw itch must be set to the
AUTO posit ion and the high beam assistant must
be switched on in the Infotainment system
¢page 47 .
• To act ivate the high beam ass istant, tap the
lever
forward @~ page 46, fig . 38. The Ii] in­
dicator light appears in the instrument cluster
display and the high beams are switched on/off
automatically. If the high beams were com­
pletely or partially switched on, the
SI indica­
tor light turns on .
Switching the high beams on/off manually
If the high beams did not switch on/off automat­
icall y as expected, you may switch them on or off
manua lly instead :
• To switch the h igh beams on manually, tap the
lever
forward @~ page 46, fig. 38. The II in­
dicator light turns on.
• To switch the high beams off manually, pull the
lever back ©¢
page 46, fig. 38. The high beam
assistant is deactivated.
Operating the headlight flasher
• To operate the headlight flasher when the high
beam assistant is activated and high beams are
switched off, pull the lever back ©¢
page 46,
fig. 38.
The high beam assistant remains ac­
tive.
Messages in the instrument cluster display
EIJ Audi adaptive light: malfunction! See own­
er's manual

u co ..... N r-­N .....
~ 0 co
~ Headlight a ssistant : ma lfun ction! See own­
er 's manual
Drive to an autho rized Audi de aler o r a uthorized
Aud i Service Facility immedia tely to have the
mal funct ion corrected. You can still switch the
high beams on or off manually.
i:a Headlight a ssistant : currently unavailable.
Camera view restricted due to surroundings .
See owner 's manual
The camera view is b locked, fo r example by a
s ticker o r debris.
The senso r is located between the interior rear­
view mir ror and the wi ndshield . Do not p lace any
sti cke rs in t his area on the wi ndshi eld.
,& WARNING
High beam assis tan t is only i ntended to assist
th e drive r. The dr iver is still re sponsib le for
contro lling the headlights and may need to
switch them on and off manually depend ing
on light and visib ility conditions. It may be
necessary to ope rate them manua lly in s itua­
tions such as:
- In adverse weather cond itions such as fog,
heavy ra in, b low ing snow or sp raying water .
- On roads where oncoming traffic may be
partially obsc ured, such as expressways .
- W hen there are road users t hat do not have
s ufficient lighting, s uc h as bicyclers o r
vehicles with dirty ta il lamps.
- In tight cu rves and on steep hills .
- In poo rly lit areas .
- Wi th stro ng ref lec to rs, such as s igns.
- I f the area of t he windsh ield near the se nso r
is f ogg ed ove r, dir ty, i cy or covere d w ith a
sti cker.
Adjusting the exterior lighting
The fun ctio ns are adjust ed in the Infotainment
system.
• Select in the Info tainment sys tem: !ME NUI but­
ton
> Vehicle > left contro l butto n > Vehicle
settings > Exterior lighting .
Lights and Vision
Automatic headlights
Yo u ca n adju st the following se ttings in the Au­
tomatic headlights
men u:
Activation time -you can adjust if the a utomat ic
he adlig hts swi tch on
Early , Medium or Late ac­
cording to the sensi tivity of the ligh t se nsor.
Headlight assistant * -you can switch the high
beam assis tan t* on and off.
Entry/exit lighting
When it is dark, the Entry/exit lighting ill umi­
nates the area a round the vehicle when unlocking
the ve hicle and afte r swi tc h ing off the ignit io n
and opening the dr ive r's door.
The
Entry /exit lighting only works when it is
dark and the ligh t sw itch is in the
AUTO position.
Daytime running lights
USA models :
the daytime r unning lig hts can be
switched on/off . Select
On or Off.
Canada model s:
th is fu ncti on canno t be switche d
off. They act ivate au tomatically eac h time the ig ­
nition is switched on.
Emergency flashers
- --- - -- ----
~
Fig . 39 Ce nter console: emergency flasher butto n
The eme rgen cy fla she rs m akes othe r dr iv e rs
aware of your vehi cle in dangerous situa tions.
• Press the ~ button to sw itch t he emergency
fl as he rs on or off.
You can ind icate a lane change or a turn when the
eme rgency flashers are swi tched on by using the
tu rn s ignal leve r. T he emergen cy flashe rs stop
tempor arily.
""
47

Lights and Vision
The emergency flashers also work when the igni­
t ion is turn ed off .
(D Tips
You s hou ld sw itch the emergency flashers on
if:
- you are the last car in a traff ic jam so that
a ll other vehicles approaching from behind
can see your vehicle
- your ve hicle has bro ke n down or you are
having an eme rgency
- you r vehicle i s being towed or if yo u are tow­
ing another vehicle
Interior lighting
Front interior lighting
F ig. 40 He adlin er: fr ont in te ri or l ig htin g
Press the co rresponding button ¢ fig . 40:
-fJ-Door contact swi tch on/off . T he interio r ligh t­
ing is controlled automatically.
- M--I n ter ior light ing o n/off
Applies to: vehicles with touch-sensitive reading lights: To turn the respect ive readi ng light on or
off, to uch the su rface @ brief ly . To act ivate the
manual d imm ing func tion , touch the surfa ce @
when the light is swi tched off and kee p touching
it unt il t he desired brig htness is reached.
48
Rear interior lighting
Fi g. 41 Headline r: re ad in g light s, vers io n 1
Fig. 42 Headline r: re ad in g l igh ts , ve rs io n 2
.. Version 1 : to turn a read ing l ight on or off,
press the
~ b utton .
.. To ac tivate the ma nual dimming f unct ion* ,
t o uch the s urface when the lig ht is swi tc h ed off
~ and keep touching it unt il t he de sired
brigh tness is reached.
.. Ver sion 2 (touch-sensiti ve reading light s with
manual dimming function* ):
to turn a reading
light on or off, br iefly touch t he surface @
¢fig. 42 .
.. To activate the manual dimming function,
to uch the surface @whe n the light is switched
off and keep touch ing it until the desired
brightness is reached .
Interior lighting
Applies to: vehicles with interior lighting
.. Select in the Infotainment system: IMENU ! but­
t on
> Vehicle > le ft cont rol but ton > Vehicle
s etting s> Interior lighting.
The inter io r li gh ting turns on when yo u sw itch
t h e headlights on w hile the ign ition is on.

Lights and Vision
move out of reverse and into another gear, the
new mirror position is stored and assigned to the
key you are using.
The mirror goes back into its original position
once you drive forward faster than 9 mph
(15 km/h) or turn t he ignition
off.
A WARNING
Curved mirror surfaces (for example convex)
enlarge the field of vision. However, they
make objects in the mirror appear smaller
and farther away. You may estimate incor­
rectly when you use these mirrors to gauge
your distance from the vehicles behind you
when changing lanes, which increases the risk of an accident.
«1j) Note
-Applies to vehicles with power folding exte­
rior mirrors: if the mirror housing was
moved by outside forces (such as an impact
when maneuvering), you must use the pow­
er folding function to fold the mirror all the
way out. The mirrors will make a loud noise
when they latch into place. The mirror hous­
ing must not be moved back into place by
hand because this would impair the func­
tion of the mirror mechanism.
- Applies to vehicles without power folding
exterior mirrors : if the mirror housing was
moved by outside forces (such as an impact
when maneuvering), you must move it back in place by hand.
- If you wash the vehicle in an automatic car
wash, you must fold the exterior mirrors in
to reduce the risk of damage to the mirrors.
Never fold power folding exterior mirrors*
by hand . Only fold them in and out using
the power controls.
(D Tips
-If the power adjusting function malfunc­
tions, the glass in both mirrors can be ad­
justed by pressing on the edge of it by hand.
- The exterior mirror settings are stored with
the memory
function*~ page 59.
so
Dimming the mirrors
Your vehicle is equipped with a manual or auto­
matic* dimming rearview mirror .
Manual dimming rearview mirror
.,. Pull the lever on the bottom of the mirror back.
Automatic dimming rearview mirror*
.,. The interior and exterior mirrors dim automati­
cally when light shines on them, for example
from headlights on a vehicle behind you.
A WARNING
If the glass on an automatic dimming mirror
breaks, electrolyte can leak out. This liquid
can irritate the skin, eyes and respiratory sys­
tem. If there is contact with the fluid, flush immediately with plenty of water. Consult a
physician if necessary .
- Repeated or long-term exposure to electro­
lyte fluid can lead to irritation of the air­
ways, especially in people with asthma or other respiratory conditions. Take deep
breaths immediately after leaving the vehi­
cle or, if this is not possible, open all of the
doors and windows as wide as possible.
- If electrolyte fluid enters the eyes, flush
them thoroughly with a large amount of
clean water for at least 15 minutes and then
seek medical attention.
- If electrolyte fluid comes into contact with
the skin, flush the affected area with clean
water for at least 15 minutes and then clean
with soap and water and seek medical at­ tention. Clean affected clothing and shoes
thoroughly before wearing again.
- If the fluid was swallowed and the person is
conscious, flush the mouth with water for at
least 15 minutes . Do not induce vomiting
unless this is recommended by medical pro­
fessionals. Seek medical attention immedi­
ately .
@ Note
If the glass on an automatic dimming mirror
breaks, electrolyte can leak out. This liquid
damages plastic surfaces and paint. Clean