2018 AUDI Q5 tires

u co ..... N r--­N ..... 0 <( 0 00
control, which increases the risk of an
accident.
@ Note
-Snow chains can damage the rims/wheel
covers* if the chains come into direct con­
tact with them . Remove the wheel covers*
first. Use coated snow chains.
-Do not install and use snow chains if there is
a malfunction in the air suspension*, be­
cause the vehicle height will be very low. If
you drive with snow chains anyway, the
wheel housings and other vehicle compo­
nents can be severely damaged.
(D Tips
When using snow chains, it may be useful to
switch the offroad mode on <=>
page 141.
Low-profile tires
App lies to: ve hicles with low -profile tires
Compared to other tire/rim combinat ions, low­
profile tires offer a wider tread surface and a
l arger r im diameter with shorter tire sidewalls.
This results in an agile dr iv ing style. However, it
may reduce the leve l of comfort and increase
road noise when driving on roads in poor condi­
tion .
L ow -profile tires can become damaged more
quickly than standard tires when driving over
l arge bumps, potholes, manhole covers, and
curbs . Therefore, it is particular ly important to
maintain the correct tire pressure<=>
page 335 .
To reduce the risk of damage to the tires and
rims, drive very carefu lly on poor roads.
Check your wheels regularly every 2,000 mi
(3,000 km) for damage. Fo r example, check for
bulges/cracks on the tires or deformations/
cracks on the rims.
After a heavy impact or damage, have the tires
and rims inspected or replaced immediate ly by
an authorized Audi dealer or authorized Audi
Service Facility .
Lo w-profile tires can wear out faster than stand­
ard tires.
Wheels
Uniform tire quality grading
-Tread wear
-Traction AA ABC
-Temperature ABC
Quality grades can be found where applicable on
the tire side wall between tread shoulder and
maximum section width <=>
page 326, fig. 266.
For example: Tread wear 200 , Traction AA, Tem­
perature A.
All passenger car tires must conform to Federal
Safety Requirements in addition to these grades.
Tread wear
The tread wear grade is a comparative rating
based on the wear rate of the tire when tested
under controlled cond it ions on a specified gov ­
ernment test course.
For example, a tire graded 150 would wear one
and one half (1 1/2) times as we ll on the govern­
ment course as a tire graded 100.
The relative performance of tires depends upon
the actual cond it ions of the ir use, however, and
may depa rt significantly from the norm due to
variations in driv ing habits, service practices and
differences in road characteristics and climate.
Traction
The traction grades, from highest to lowest, are
AA , A, Band
C. Those grades represent the tire's
ability to stop o n wet pavement as measured un­
der controlled conditions on specified govern­
ment test surfaces of asphalt and concrete. A tire
marked C may have poor traction performance
c:>,& .
Temperature
The temperature grades are A (the highest), B,
and C, representing the tire's resistance to the
generation of heat and its ability to dissipate
heat when tested under controlled conditions on
a specified indoor laboratory test wheel.
Sustained high temperature can cause the mate­
rial of the tire to degenerate and reduce tire life,
and excessive temperature can lead to sudden
tire failure
c:> ,& . ..,.
341

Wheels
The grade C corresponds to a leve l of perform ­
ance which all passenger car tires must meet un­
der the Federa l Motor Vehicle Safety Standard
No.
109. Grades Band A represent higher levels
of performance on the laboratory test wheel than
the minimum required by law.
A WARNING -
The traction grade ass igned to this tire is
based on straight-ahead braking traction
tests, and does not include acce le rat ion, cor­
ne ring, hydroplaning or peak traction charac­
teristics.
A WARNING
Th e temperatu re grade for this tire is estab­
lished for a tire that is properly inflated and
not overloaded. Excessive speed, underinfla­
tion, or excessive loading, either separate ly or
in combination, can cause heat buildup and
possible tire failure.
A WARNING
-
-
Temperature grades apply to tires that are properly inflated and not over or underinflat­
ed.
Tire pressure monitoring system
(l) General notes
Each t ire, including the spare (if provided),
should be checked monthly when cold and inflat­
ed to the inflation pressure recommended by the
ve hicl e manufacturer on the vehicle placard or
tire in flatio n press ure label. ( If yo ur vehicle has
t ires of a different siz e than the size indicated on
the vehicle placard or tire inflation pressure la­
be l, you should determine the proper tire infla­
tion pressure for those t ires) .
As an added safety feature, your veh icle has been
equipped with a tire pressure monitoring system
(TPMS) that illuminates a low tire pressure te ll­
tale when one or more of your t ires is significant­
ly under-inflated. Accordingly, when the low tire
pressure tellta le illuminates, you should stop and
342
check your tires as soon as possible, and inflate
them to the proper pressure . Driving on a signifi ­
cant ly under-inflated t ire causes the t ire to over­
heat and can lead to tire fa ilure . Under-inflation
also reduces fue l eff iciency and tire tread life,
and may affect the vehicle's handling and stop ­
ping ability .
Please note that the TPMS is not a substitute for
proper tire maintenance, and it is the dr iver's re­
spons ibility to maintain correct tire pressure,
even if under-inflation has not reached the level
to trigger illumination of the TPMS low tire pres­
su re te lltale .
Your vehicle has also been equipped with a TPMS
malfunction indicator to indicate when the sys­
tem is not operating prope rly . The TPMS mal­
function indicat or is combined with the low tire
pressure telltale. When the system detects a
malfunction, the telltale will flash for approxi ­
mately one minute and then remain continuously
illuminated. This sequence wi ll continue upon
s ub sequent vehicle start-ups as long as the mal­
funct ion exists.
When the malfunction indicator is illuminated,
the system may not be able to detect or signal
l ow tire pressure as intended. TPMS malfunctions
may occur for a variety of reasons, including the
i nstallation of replacement or alternate tires or
wheels on the veh icle that prevent the TPMS
from functioning properly. Always check the
TPMS ma lfunction telltale after replac ing one or
more tires or wheels on you r vehicle to ens ure
that the rep lacement or alternate tires and
whee ls allow the TPMS to continue to function
properly.
If the tire pressure monitoring indicator
appears
App lies to : vehicles wit h Tire Pressure Mo nitor ing System in­
dicator
The tire pressure indicator in the instrument
cluster informs you if the tire pressure is too low
or if there is a system malfunction .
Using the ABS sensors, the tire pressure monitor­
in g system compares the tire tread circumfer­
en ce and vibration characteristics of the

individual tires. If the pressure changes in one or
more tires, this is indicated in the instrument
cluster display with an indicator light
[IJ and a
message . If only one tire is affected, the location
of that tire will be indicated.
The tire pressures must be stored in the Infotain­ ment system again each time the pressures
change (switching between partial and full load
pressure) or after changing or replacing a tire on
your vehicle
¢ page 343 . The tire pressure moni­
toring system only monitors the tire pressure you
have stored. Refer to the tire pressure label for
the recommended tire pressure for your vehicle
¢ page 335, fig. 269.
Tire tread circumference and vibration character­
istics can change and cause a tire pressure warn­
ing if:
- the tire pressure in one or more tires is too low
- the tires have structural damage
- the tire was replaced or the tire pressure was
changed and it was not stored
¢ page 343
- tires that are only partially used are replaced
with new tires
Indicator lights
[IJ-loss of pressure in at least one tire¢,&. .
Check the tires and replace or repair if necessary.
Check/correct the pressures of all four tires and
store the pressure again in the Infotainment sys­
tem
¢ page 343 .
mm (Tire Pressure Monitoring System) Tire
pressure: malfunction! See owner's manual.
If
mm appears after switching the ignition on or
while driving and the
[IJ indicator light in the in­
strument cluster blinks for approximately one minute and then stays on, there is system mal­
function . Try to store the correct tire pressures
~ page 343 . In some cases , you must drive for
several minutes after storing the pressures until
the indicator light turns
off. If the indicator light
does turn off or turns on again after a short peri­
od of time, drive to an authorized Audi dealer or
authorized Audi Service Facility immediately to
~ have the malfunction corrected. .... N ,..._
N ..... 0 <( 0 00
Wheels
A WARNING
--- If the tire pressure indicator appears in the
display, reduce your speed immediately and
avoid any hard steering or braking maneu­
vers. Stop as soon as possible and check the
tires and their pressure.
- The driver is responsible for maintaining the
correct tire pressure. You must check the
tire pressure regularly .
- Under certain conditions (such as a sporty
driving style, winter conditions or unpaved
roads), the tire pressure monitoring system
indicator may be delayed.
@ Tips
- The tire pressure monitoring system can al­
so stop working when there is an ESC mal­
function.
- Using snow chains may result in a system
malfunction.
- The tire pressure monitoring system in your
Audi was calibrated with
"Audi Original
Tires"~ page 332. Using these tires is rec­
ommended.
Storing tire pressures
App lies to: vehicles wi th Tir e Pr essure Mo nito ring Syste m in­
dica tor
If the tire pressure changes or a tire is replaced ,
it must be confirmed in the Infotainment sys­ tem .
.. Before storing the tire pressures, make sure the
tire pressures of all four tires meet the speci ­
fied values and are adapted to the load
¢page 335 .
.. Switch the ignition on .
.. Select in the Infotainment system: I MENU ! but­
ton
> Vehicle > Service & checks > Tire pres­
sure monitoring
> Store tire pressure > Yes,
store now.
(D Tips
Do not store the tire pressures if snow chains
are installed .
343

Care and cleaning
Care and cleaning
General information
Regular, proper care helps to maintain your vehi­
cle's value. It can also be a requirement when
submitting warranty claims for corrosion damage
and paint defects on the body.
The required cleaning and care products can be
obtained from an authorized Audi dealer or au­
thorized Service Facility . Read and follow the in­
structions for use on the packaging .
A WARNING
-Using cleaning and care products incorrectly
can be dangerous to your health.
- Always store clean ing and care products out
of reach of children to reduce the r isk of poi­
son ing.
@ For the sake of the environment
- Preferab ly purchase environmenta lly-friend­
l y cleaning products.
- Do not dispose of leftover cleaning and care
products with household trash.
Car washes
The longer that deposits such as insects, bird
droppings, tree sap or road salt remain on the ve­
h icle, the more the surface can be damaged. High
temperatures such as those caused by sunlight
increase the damaging effect.
Before washing, r inse
off heavy deposits with
p lenty of water.
Stubborn deposits such as bird droppings or tree
sap are best removed with plenty of water and a microfiber cloth.
A lso, wash the underside of yo ur vehicle once
road sa lt stops being used for the season .
Pressure washers
When washing your veh icle w ith a pressure wash­
er , al ways fo llow the operating instructions pro­
vided with the press ure washer. This is especially
important in regard to the pressure and spraying
distance. Do not aim the spray directly at the
344
seals on the side windows, doors, lids or the sun­
roof* or at tires, rubber hoses, insulating materi ­
a l, sensors* or camera lenses* . Keep a distance of
at least 16 in (40 cm).
Do not remove snow and ice with a pressure
washer.
Never use cone nozz les or high pressure nozzles.
The water temperature must not be above 140 °F
(60 °() .
Automatic car washes
Spray off the vehicle before washing.
Make sure that the windows and roof* are closed
and the windshie ld wipers are
off . Follow instruc ­
tions from the car wash operator, especially if
there are accessories attached to your vehicle.
If possible, use car washes that do not have
brushes.
Washing by hand
Clean the vehicl e starting from the top and work­
in g down using a soft sponge or cl eaning br ush.
Use solvent-free cleaning products.
Washing vehicles with matte finish paint by
hand
To avoid damaging the paint when washing, first
remove dust and large part icles from you r vehi ­
cle. Insects, grease spots and fingerprints are
best removed with a special cleaner for matte
finish paint .
Apply t he product using a microfiber cloth. To
avoid damaging th e paint surface, do not use too
much pressure.
R inse the vehicl e thoroughly with wate r. Then
clean using a neutra l shampoo and a soft micro­
f iber cloth .
Rinse the vehicl e thoroughly again and let it air
dry. Remove any water residue using a chamois.
A WARNING
-Only wash the vehicle when the ignition is
off and follow the instructions from the car
-

u co ..... N r--­N ..... 0 <( 0 00
wash operator to reduce the risk of acci­
dents.
- To reduce the risk of cuts, protect yourself
from sharp metal components when wash­ ing the underbody or the inside of the wheel
housings.
- After washing the vehicle, the braking effect may be delayed due to moisture on the
brake rotors or ice in the winter . This in­
creases the risk of an accident. The brakes
must be dried first with a few careful brake
applications.
@ Note
- If you wash the vehicle in an automatic car
wash, you must fold the exterior mirrors in
to reduce the risk of damage to the mirrors.
Power folding exterior mirrors* must only
be folded in and out using the power folding
function.
- To reduce the risk of damage to the rims
and tires, compare the width between the
wheels on your vehicle with the distance be­
tween the guide rails in the car wash.
- To reduce the risk of damage, compare the
height and width of your vehicle with the
Care and cleaning
height and width of the inside of the car
wash .
- T o reduce the risk of paint damage, do not
wash the vehicle in direct sunlight .
- To reduce the risk of damage to the surface,
do not use insect removing sponges, kitchen
sponges or similar items .
- Matte finish painted vehicle components:
- To reduce the risk of damage to the sur-
face, do not use polishing agents or hard
wax.
- Never use protective wax. It can destroy
the matte finish effect .
- Do not place any stickers or magnetic
signs on vehicle parts painted with matte
finish paint. The paint could be damaged
when the stickers or magnets are re­
moved.
@ For the sake of the environment
Only wash the vehicle in facilities specially de­
signed for that purpose. This will reduce the
risk of dirty water contaminated with oil from
entering the sewer system.
Cleaning and care information
When cleaning and caring for individual vehicle
components, refer to the following tables. The
information contained there is simply recom­
mendations. For questions or for components that
are not listed, consult an authorized Audi
dealer or authorized Audi Service Facility. Also
follow the information found
in ¢.&. .
Exterior cleaning
Component Situation Solution
Windshield wiper
Deposits soft cloth with glass cleaner, ¢ page 52
blades
Headlights/
Deposits Soft sponge with a mild soap solution3>
Tail lights
Sensors/
Deposits Sensors: soft cloth with a solvent-free cleaning solution
camera lenses Camera lenses: soft cloth with an alcohol-free cleaning
solution
Snow/ice Hand brush/solvent-free de-icing spray
Wheels Road salt Water
Brake dust Acid-free special cleaning solution
345

u co ..... N r-­N .....
~ 0 co
The tire repair is only meant for temporary use.
Change the spare tire as soon as
possib le ¢ Li:\. .
If the tire is pierced by an object such as a nail,
do not remove the object from the tire.
The tire mobility kit can be used at temperatures
as low as -4 ° F (- 20 °C).
The tire mobility kit m ay not be u sed:
- if the tire has cuts or punctures that are larger
than 0.16 in (4
mm) @¢ fig. 271
-if the rim is damaged @
- if you drove with very low tire pressure or with-
out air in the tire @
See an authorized Aud i dealer or authorized Aud i
Service Facility for assistance in these situations.
A WARNING
- Please note that the tire mobility kit cannot
be used in all situations, and that it may on­
ly be used temporari ly.
- The tire sealant must not come in contact
with sk in, eyes, or clothes.
- If tire sealant gets in your eyes or on your
sk in, thoroughly rinse the affected area im­
med iately w ith clean water.
- Do not inhale the fumes .
- If you swallow any of the tire sealant, thor-
oughly rinse yo ur mouth immediately and
drink a lot of water. Do not induce vomiting.
Seek medical attention immediately.
- Change your clothes immediate ly if they get
t ire sealant on them.
- If an allergic reaction occurs, seek immedi­
ate medical attention.
- Keep the tire sea lant away from children .
(D Tips
-If se alant lea ks, allow it to dry i n place. Yo u
can then pee l it off like a sticker.
- Note the expiration date on the sealant bot ­
tle . Replace the tire sea lant at a n author­
i zed Audi dealer or author ized Audi Se rvice
Facility .
- Radio reception can be i nterrupted when
operating the compressor.
- Obey all laws.
Em ergen cy as sis tanc e
Repairing tires
Applies to : veh icles w it h tire mo bility k it
F ig. 2 72 Co mponents of t he tire mob ility k it
Fig . 273 Tire mobil ity kit connect ion
Requirement: the tire mobility kit must be laid
out and ready for
use ¢ page 350 .
Installing the tire mobil ity k it
.,. Open the cover @on the compressor
¢fig. 272 .
N
l!l 0
ct m
.,. Remove the connector © and pressure hose ®
w ith pressure gauge from the housing .
.,. Install the compressor pressure hose ® onto
the flange @ on the t ire sealant bottle
(J) .
.,. Insert the sea lant bott le with the flange at the
bottom into the opening @ on the compressor
cover .
.,. Remove the valve cap from the faulty tire .
.,. Install the filler hose @) on the valve 0
¢fig. 273.
.,. Connect the plug ©¢ fig. 2 72 to an outlet in
the vehicle.
.,. Switch the ignit ion on .
Inflating a tire
.,. Move the switch ®¢ fig. 2 73 on the compres-
sor into position
I. .,..
351

u co ..... N r-­N .....
~ 0 co
(D Tips
The vehicle jack mode* switches off automati­cally at speeds above 6 mph (10 km/h) .
Removing and installing a wheel
Fig. 278 Wh eel: i nt ern al hex so cket to turn th e w hee l
b olts
Fig. 279 Wheel: alignment pin in the top hole
Remo ving a wheel
.,. Remove the top wheel bolt complete ly using
the hex socket in the screwdriver handle (in the
vehicle tool kit)
c::> fig. 2 78 and place it on a
clean surface .
.,. The n install the alignment pin (from the vehicle
tool kit) by hand into the empty wheel bolt ho le
c::>fig . 279.
.,. Remove the rest of the wheel bolts .
.,. Remove the wheel c::>G). The al ignm ent pi n re-
mains in the hole while doing this.
Install a wheel
Read the direct ions on c::> page 355 when ins tal­
ling unidirectional tires .
.,. Slide the wheel on over the alignment pin c::> 0 .
.,. Install the wheel bo lts and tighten gen tly using
t h e hex socket .
Emergen cy as sis tanc e
.,. Remove the alignment pin and also tighten the
remaining whee l bolt .
.,. Carefully lower the vehicle using the vehicle
jack* .
.,. T ighten the wheel bolts in a diagonal pattern
using the wheel wrench .
The wheel bolts must be clean and loosen/tight ­
en easily. Check the contact surfaces for the
whee l and hub. Contam inants on the se surfaces
must be removed before install ing the whee l.
A WARNING ~
Never use the hex socket in the screwdriver
handle o r the hex socket wrench with the
ra tc het to loosen or tighten the wheel bolts.
This increases the risk of an ac cident, because
you will not reach the tightening specif ication
required .
(D Note
When removing o r instal lin g the wheel, the
rim co uld h it the br ake rotor and damage t he
rotor . Work carefully and have a second per ­
son help you .
(D Tips
-When mount ing tires with unidirectional
tread de sign
make sure the tread pattern is
pointed the right way
c::> page 355 .
- T he wheel bolts sho uld be clean and easy to
t u rn. Check for dirt and corrosion on the
mating surfaces of both the wheel and the
hub. Remove all dirt from these s urfaces
be­
fore remounting the wheel.
Unidirectional tires
-
A un idirectional t ire profi le is identified by arrows
that point in the r unning direct ion on the tire
s idewa ll. You must always adhe re to the spec i­
fied ru nning direction. Th is is necessary ensure
the tire's opt imum pe rformance in reg ard to
ad ­
hesion, runni ng no ise, friction and hydroplaning .
T o benefit fully from the advantages of the uni­
directional t ire design, yo u should replace fa ulty
t ir es as soon as possible and restore the correc t
runn ing direction on all of the t ires.
355

Emergency assistance
Finishing
.,. Reinstall the caps on the whee l bolts if neces ­
s ar y.
.,. Store the vehicle tool kit i n its design ate d
p lace .
.,. If the removed whee l does not fit in the spare
whee l we ll, store it sec ure ly in t he luggage
compartment
c::> page 257.
.,. Check the tire press ure on the installed whee l
as soon as possible .
.,. Correct the tire pressure a nd s to re i t in the I n­
fota inment system
c::> page 343 .
.,. The w heel bo lt tig hte ning spe cifica tion mus t be
1 00 f t lbs ( 140 N m). C heck it as soon as p ossi­
ble wi th a t orq ue w rench . Drive care fully unti l
then .
.,. Have the faulty wheel rep laced as quick ly as
poss ib le .
(D Tips
- If you notice t hat the w hee l bo lts are cor­
r oded and diffic ult to t urn wh ile chan ging a
tire, they sh ould be replaced before you
chec k the tig htening torque.
- D rive at reduced speed until you have the
tig htening torques c hec ke d .
Notes on wheel changing
Please read the info rmation c::> page 332 if you
are go ing to use a replaceme nt tir e w hich is dif­
f er ent fro m the tires on your v ehicle.
Afte r you change a t ire:
- Check the tire pressure on the replacement
tire immediately after installation.
- Have the wheel bolt tightening torque
checked with a torque wrench as soon as pos­
sible by your authorized Audi dealer or quali­
fied workshop.
- With steel and alloy wheel rims , the wheel
bolts are correctly tightened at a torque of
100 ft lbs (140 Nm) .
- If you notice that the wheel bolts are corroded
and difficult to turn while changing a tire,
they should be replaced before you check the
tightening torque.
356 -
Replace the flat tire with a new one and have
it installed on your vehicle as soon as possi­
ble. Remount the wheel cover.
Until then, drive with extra care and at reduced
speeds.
_&. WARNING
- If you are going to equip yo ur vehicle with
tires or r ims which diffe r from those which
were facto ry installed, then be sure to read
the information
c::> page 332 .
- Always make sure the damage d w heel or
even a flat tire and the jack* and too l kit are
properly secured in the luggage compart­
m en t and a re not loos e in the pass eng er
compa rtm ent .
- In a n accide nt or sudden maneuv er they
could fly forward, i njuring anyo ne in the ve­
hicle .
- Always s to re damaged wh eel, jack* an d
t oo ls sec urely in th e luggage com partm ent .
O the rwise, in an a ccide nt or sud den ma neu ­
v er they co u ld fl y forw ard, c ausi ng injur y to
pa ssengers in the ve hicl e.
-
Collapsible spare tire
App lies to: vehicles wit h co llapsible spare t ire
The co llaps ib le spa re tir e is i nte nded fo r sho rt­
t e rm use o nly. H ave the d amage d tire checked
a nd rep lac ed , if necess ary, by an autho riz ed Audi
d ealer or au thor ized A udi Se rvi ce Fac ility as soo n
as possible.
T here a re so me restr ictions o n the use of the co l­
lap sib le spar e tir e. The coll apsible spar e tir e h as
b een desig ned s pecif ic a lly for your type o f vehi ­
cl e. Do not rep lace it wit h the co llaps ible spa re
ti re from a nother type of vehicle .
T he collapsibl e spar e tir e is l oc at e d i n the l ug­
g age co mpa rtmen t under the ca rgo floo r cover .
Requireme nt: t he v ehicl e too l ki t
c::> pag e 350 and
th e co mpr ess or m ust b e laid out.
Removing
.,. Fold th e cargo floor cove r back c::> page 350 ,
fig. 270 .