2018 AUDI Q3 emergency towing

Driving
Your vehicle is equipped with an electromechani­
cal parking brake @
c> fig. 71. The parking brake
is designed to prevent the vehicle from rolling
un intent ionally and replaces the hand brake .
Setting/manuall y releasing the pa rking
brake
... Pull the(®) switch to set the parking brake . The
LED in the sw itch turns on. The -(USA mod­
els) . (Canada models) indicator light also
turns on in the instrument cluster display .
.,. To release the parking brake manually, press
the b rake o r accelerato r pedal whi le the igni­
tion is switched on and p ress t he
C®) switch a t
the same time. The L ED in t he b utton and t he
i ndica tor light in the display turn off .
Releasing the parking brake automatically
Requirement: the dr iver's door must be closed,
the dr iver's safety be lt must be latched and the
pa rking brake must be set.
... To start driving and re lease the park ing brake
automat ica lly, press the accele rato r pedal as
us ua l.
In addi tion to releasing the park ing brake auto­
mat ically, other convenience and safety funct ions
are available whe n you start driving
c> page 65,
Starting from a stop .
Preventing the automatic parking brake
release
The vehicle could begin rolling unintentionally ,
dependi ng on the h ill or if towing a trailer .
... To preve nt the parking brake from releasing au­
tomat ica lly, pull and hold the®) sw itch and
press the accelerator pedal. The park ing b rake
remains set and prevents the veh icle from ro ll­
in g backward.
.,. Yo u can re le ase the(®) switch aga in once you
are sure that you are g iv ing eno ugh dr iv ing
force to the wheels by pressing the accele rator
pedal.
Emergency braking function
You can use the emergency bra king f unct ion in an
emergen cy situ ation , or if the stand ard bra ke op­
era tion mal func tions or is disabled.
64
... Pull and ho ld the C®) swi tc h.
... As soon as you re lease the
C®> switch or acceler-
ate, the braking stops.
P ulli ng and ho ld ing t he
C®) switch wh ile driving
the veh icle activates the eme rgency braking func ­
tion . The ve hicle is bra ked at a ll four wheels by
activating the hydraulic b rake system . The bra k­
i ng effect is sim ilar to heavy brak ing
c> ,&. .
To reduce the risk of act ivat ing t he emergency
bra kin g by mista ke, a warning tone (buzzer)
sounds when the
C®) sw itch is p ulled . Eme rgency
braking stops as soon as the© switch is released
or the accelerator pedal is pressed.
Park ing
... Press the brake peda l to stop the ve hicle.
... Pull the
C®> switch to set the par king brake .
... Place the selecto r lever in the P position .
... Turn the engine off
c> ,&. .
... Turn the steering w heel when parking on in­
clines so that the w heels w ill roll into the curb
if the vehicle starts moving.
8,,. WARNING
- Do not press the a ccele ra to r peda l inadve r­
tently if a ge ar i s selected whe n the vehicle
is st ationary an d th e engine is running . Oth­
erwise, the vehicle will s tart to move imme ­
diate ly and this could result i n an accident.
- Eme rgency brak ing s hou ld only be used i n
an emergency, when the norma l bra ke pe dal
has failed or the bra ke peda l is obstructed .
During eme rgency brak ing, your vehicle will
brake s imilar to heavy braking. ESC and the
associated components (ABS, ASR, EDL)
cannot ove rcome the laws of physics .
Around curves a nd whe n road or wea ther
conditions a re bad, a full brake applicat io n
can ca use the veh icle to skid or the rear end
to swerve, w hich incr eases the ris k of an ac­
cident.
- I f th e power s upply fail s, you cannot set the
parking br ake if it is released. In this case,
pa rk the vehicle on leve l ground and secure
it by p lacing the selector leve r in the P posi­
tion. See an authorized A udi dealer or au -
thorized A udi Service Fac ility for assistance.
IIJ.

0 co ......
"' ,....
"' ...... 0 0 :::,
00
wait for the engine to slow down to idle
before selecting Dor S.
- If there is a power failure, the selector lever
will not move out of the P position. The
emergency release can be used if this hap­
pens
¢ page 72.
Driving tips
Starting the engine
~ The selector lever must be in the P or the N po ­
sition.
Starting from a stop
~ Press and hold the brake pedal.
~ Press and hold the lock button in the selector
lever handle, select the desired selector lever
position such as D ¢
page 67 and release the
lock button.
~ Wait a moment until the transmission shifts .
You will notice a slight movement when the gear engages .
~ Release the brake pedal and press the accelera-
tor pedal ¢,&. .
Various convenience functions are available for
starting on hills
¢ page 65 .
Stopping temporarily
~ Press the brake pedal to stop the vehicle, for
example at a traffic light. Do not press the ac­
celerator pedal when doing this .
~ To prevent the vehicle from rolling when you
start driving, set the parking brake when stop­
ping on steep hills ¢
8. and ¢0.
~ The parking brake will release automatically
and the vehicle will start moving once you press
the accelerator pedal.
Stopping/parking
If the selector lever is not in the P position when
you open the driver's door, the vehicle could roll.
In vehicles with a convenience key*, the message
Shift to P and turn off ignition, or vehicle can
roll away
appears.
~ Press and hold the brake pedal¢,&. .
~ Set the parking brake .
~ Select the P selector lever position .
Driving
Under certain circumstances, (such as driving in
the mountains or towing a trailer), it may be use­
ful to switch temporarily to the manual shift pro­
gram in order to adjust the gears to the driving
conditions by hand
¢page 70.
On inclines, activate the parking brake first and
then move the selector lever to the P position
¢
page 64. This prevents the locking mechanism
from being loaded too heavily and will make it
easier to move the selector lever out of the P po ­
sition.
A WARNING
= -- The vehicle can roll even when the engine is
switched off.
- Unintended vehicle movement can lead to
serious injuries .
- Never leave your vehicle with the engine
running while in gear. If you must leave
your vehicle when the engine is running, set
the parking brake and move the selector lev­
er to the P position.
- Power is still transmitted to the wheels
when the engine is running at idle. To pre­
vent the vehicle from "creeping", you must
keep your foot on the brake in all selector
lever positions (except P) when the engine is
running.
- Do not inadvertently press the accelerator
pedal when the vehicle is stopped if a gear is
engaged. Otherwise the risk of an accident
increases because the vehicle will start to
move immediately, even if the parking brake
is set.
- To reduce the risk of an accident, do not
press the accelerator pedal when changing
the selector lever position while the vehicle
is stationary and the engine is running.
- Never engage the R or P selector level posi­
tions while driving. It could cause a crash.
- Before driving down a steep slope, reduce your speed and shift into a lower gear in tip­tronic mode.
- Do not ride the brakes or press the brake
pedal too often or too long when driving
downhill. Constant braking causes the
brakes to overheat and substantially ..,.
69

0 co ......
"' ,....
"' ...... 0 0 :::,
00
Emergency situations
General
This chapter is intended for trained emergency
crews and working personnel who have the nec­
essary tools and equipment to perform these
operations.
Starting by pushing or
towing
CD Note
Vehicles with an automatic transmission
cannot be started by pushing or towing.
Starting with jumper
cables
If necessary, the engine can be started by con­
necting it to the battery of another vehicle.
If the engine should fail to start because of a dis­
charged or weak battery, the battery can be con­
nected to the battery of
another vehicle, using a
pair of jumper cables to start the engine.
Jumper cables
Use only jumper cables of sufficiently large cross
section
to carry the starter current safely. Refer
to the manufacturer's specifications.
Use only jumper cables with
insulated terminal
clamps which are distinctly marked:
plus(+) cable in most cases colored red
minus(·) cable
in most cases colored black.
A WARNING
Batteries contain electricity, acid, and gas.
Any of these can cause very serious or fatal in­
jury. Follow the instructions below for safe
handling of your vehicle's battery.
-Always shield your eyes and avoid leaning
over the battery whenever possible.
-A dead battery can freeze at temperatures
around 32 °F (0 °C). If the vehicle battery is
frozen, you must thaw it before connecting
the jump start cables. If you do not, this in-
Emergency situations
creases the risk of an explosion and chemi­
cal burns. After jump starting the vehicle,
drive to an authorized Audi dealer or author­
ized Audi Service Facility immediately to
have the vehicle battery checked.
- Do not allow battery acid to contact eyes or
skin . Flush any contacted area with water
immediately.
- Improper use of a booster battery to start a
vehicle may cause an explosion .
- Vehicle batteries generate explosive gases.
Keep sparks, flame and lighted cigarettes
away from batteries.
- Do not try to jump start any vehicle with a
low acid level in the battery .
- The voltage of the booster battery must also
have a 12-Volt rating. The capacity (Ah) of
the booster battery should not be lower
than that of the discharged battery. Use of
batteries of different voltage or substantial­
ly different "Ah" rating may cause an explo­
sion and personal injury.
- Never charge a frozen battery. Gas trapped
in the ice may cause an explosion.
- Never charge or use a battery that has been
frozen . The battery case may have be weak­
ened.
- Use of batteries of different voltage or sub­
stantially different capacity (Ah) rating may
cause an explosion and injury. The capacity (Ah) of the booster battery should not be
lower than that of the discharged battery.
- Before you check anything in the engine
compartment, always read and heed all
WARNINGS
qpage 155.
CD Note
-Applying a higher voltage booster battery
will cause expensive damage to sensitive electronic components, such as control
units, relays, radio, etc.
- There must be no electrical contact between
the vehicles as otherwise current could al­
ready start to flow as soon as the positive
(+) terminals are connected.
203

-Do not bend over the batteries -danger of
chemical burns!
- The battery cell locking screws must be
tightened securely.
- Before you check anything in the engine
compartment, a lways read and heed all
WARNINGS
¢ page 155.
(D Note
Improper hook-up of jumper cables can ruin
the generator.
- Always connect POSITIVE(+) to POSITIVE
( + ), and NEGATIVE(-) to NEGATIVE(-)
ground post of the battery manager contro l
unit.
- Check that all screw p lugs on the battery
cells are screwed in firmly . If not, tighten
plugs prior to connecting clamp on negative
battery terminal.
- Please note that the procedure for connect­
ing a jumper cable as described above ap­
plies specif ically to the case of your vehicle
being jump started. When you are giv ing a
jump start to another vehicle, do
not con­
nect the negative( -) cab le to the negative
(-) terminal on the discharged battery@
¢ fig. 161. Instead, securely connect the
negative (-) cable to either a solid metal
component that is firm ly bolted to the en­
gine block or to the engine block itself. If
the battery that is being charged does not
vent to the outs ide, escaping battery gas
could ignite and explode!
Towing with a tow truck
General hints
Your Audi requires special handling for towing .
The following information is to be used by com ­
mercial tow tr uck operators who know how to op­
erate their equipment safely .
-Never tow your Audi, towing will cause dam-
age to the engine and transmission .
a '.:: -Never wrap the safety chains or winch cables
~ around the brake lines. N
"" 0 0 ::, (X)
Emergency situations
-To prevent unnecessary damage , your Audi
must be transported with a flat bed truck.
- To load the vehicle on to the flat bed, use the
towing loop found in the vehicle tools and at·
tach to the front or rear anchorage
¢ page 205 and ¢ page 206.
A WARNING ~ -
A veh icle being towed is not safe for passen­
gers . Never allow anyone to ride in a vehicle
being towed, for any reason.
Front towing loop
Only install the front towing loop when it is
needed.
®
®
0 0:, N 9 ::> 0:, a)
Fig. 162 Front bumpe r on t he r ight s ide: remove t he cover
Fig. 163 Front bumpe r on t he right side: screw in the tow-
in g loop ...
205

Emergency situations
The threaded opening for the towing loop is lo­
cated behind a cover on the right side of the front
bumper. Depending on the version, the cover can
be removed in different ways¢
fig. 162 .
... Version @: remove the towing loop and the
hook from the vehicle tool kit
r=> page 191. Or
... Version @: remove the towing loop from the
vehicle tool kit
r=> page 191 .
... Version @: insert the hook into the hole on the
cover and carefully pull off the cover in the di ­
rection of the arrow¢
fig. 162 . Or
.,. Version @: press the cap inward with brief,
fo rceful pressure
r=;, fig. 162. Th e cap w ill loosen
from the bumper.
... Tighten the towing loop in the threaded open­
ing until it stops
r=;, fig. 163 and then tighten it
with a wheel wrench.
... After using, place the towing loop back in the
vehicle tool kit.
A WARNING
If the towing loop is not tightened until it
stops when insta lling, the threads may be
pulled out when tow ing the veh icle and that
cou ld cause an accident.
Rear towing loop
Fig. 164 Rear bumpe r: cover
206
-
Fig. 165 Rear bumper : install ing the tow ing loop
Vehicles with a towing loop
On vehicles without a factory -installed trailer
hitch*, the rear towing loop is located on the
right side of the bumper .
... Remove the towing loop from the vehicle tool
kit
r=;, page 191 .
.,. Press the cap inward with brief , forceful p res­
sure
r=> fig. 164 . The cap will loosen from the
bumper.
8l N 9 ::, co m
... Tight en the towing loop in the threaded open­
ing until it stops
r::!;> fig. 165 and then tighten it
with a wheel wrench.
... After using, place the towing loop back in the
vehicle tool kit .
Vehicles with a trailer hitch*
... Til t the trailer hitch out .
... Attach the towing bar or the towing cable to
the trailer hitch .
A WARNING
If the towing loop is not tightened until it
stops when installing, the threads may be pulled out when towing the vehicle a nd that
could cause an accident .
A WARNING
Applies to: vehicles with trailer hitch
-
- Only use a spec ial towing bar to prevent
damagi ng the ball hitch. These towing bars
have been specially designed for trailer tow­
ing hitches.
- Only use special towing cab les.

Index
Sunroof
refer to Panorama glass roof . . . . . . . . . . . 31
Sunshade
Emergency closing (panorama glass roof) .
32
Sun visors . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 7
Symbols
refer to Indicator lights . . . . . . . . . . . . . . . . 10
T
Tachometer. . . . . . . . . . . . . . . . . . . . . . . . . . 8, 9
Technical data . . . . . . . . . . . . . . . . . . . . . . . . 209
Technical modifications . . . . . . . . . . . . . . . . 215
Temp erature display
Outside temper ature . . . . . . . . . . . . . . . . . . . 9
Temperature indicator Coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
Temporary spare tire . . . . . . . . . . . . . . . . . . 197
Tether anchors . . . . . . . . . . . . . . . . . . . . . . . 149
Tether strap . . . . . . . . . . . . . . . . . . . . . . . . . 149
Tie-down rings . . . . . . . . . . . . . . . . . . . . . . . 103
Tie -downs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Time . .... .. .. .. ............. .... .. ... 9
tiptronic mode (automat ic transmission) . . . 70
tiptronic (automatic transmission) . . . . . . . . 66
Tires................................ 166
All
wheel drive . . . . . . . . . . . . . . . . . . . . . . . 93
Low-profile tires . . . . . . . . . . . . . . . . . . . . . 182
Replacing . . . . . . . . . . . . . . . . . . . . . . . . . . 191
Service life . . . . . . . . . . . . . . . . . . . . . . . . . 17 5
Tire pressure . . . . . . . . . . . . . . . . . . . . . . . 176
Tir e pressure monitoring system . . . . . . . 183
Tire pressure table . . . . . . . . . . . . . . . . . . . 177
Tire pressure (trailer towing) . . . . . . . . . . . 73
Treadwear indicators . . . . . . . . . . . . . . . . .
175
Unidirectional . . . . . . . . . . . . . . . . . . . . . . . 168
Uniform tire quality grading . . . . . . . . . . . 182
Tires and wheels
Glossary of tire and loading terminology .
169
Tires and vehicle load limits . . . . . . . . . . . 17 8
Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 1
Torn or frayed safety belts . . . . . . . . . . . . . . 108
Towing
Tow trucks . . . . . . . . . . . . . . . . . . . . . . . . .
205
Towing loop . . . . . . . . . . . . . . . . . . . . . 205, 206
TPMS (Tire Press ure Monitoring System) . . 183
224
Trailer towing . . . . . . . . . . . . . . . . . . . . . . . . . 73
Parking systems . . . . . . . . . . . . . . . . . . . . . .
88
Trailer load . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Turn signals . . . . . . . . . . . . . . . . . . . . . . . . .
16
Transport Canada . . . . . . . . . . . . . . . . . . . . . 104
Turn signal . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
u
Unfastening safety belts
Uniform tire quality grading
Unlocking/ locking 111
182
By remote control . . . . . . . . . . . . . . . . . . . . 24
With the central locking sw itch . . . . . . . . . 25
With the convenience key . . . . . . . . . . . . . . 24
Use of jumper cables . . . . . . . . . . . . . . . . . . 204
V
Vanity mirror.... .. .. .. ............. ... 37
Vehicle Care/cleaning . . . . . . . . . . . . . . . . . . . . . . .
185
D .
. 1mens1ons ...... .. .. .............. .
Out of service .. .. .. .. .. ........... . .
Specifications ..................... . . 210
190
209
Vehicle battery . . . . . . . . . . . . . . . . . . . . . . . 163
Charge leve l . . . . . . . . . . . . . . . . . . . . . . . . . 94
Charging . . . . . . . . . . . . . . . . . . . . . . . . 13, 164
Energy management . . . . . . . . . . . . . . . . . . 94
Vehicle control modules . . . . . . . . . . . . . . . . . 95
Vehicle jack . ... ... .. .. ... ..... ... 191,194
Vehicle key . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Vehicle tool kit . . . . . . . . . . . . . . . . . . . . . . . 191
VIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209
w
Warning lights
refer to Indicator lights . . . . . . . . . . . . . . . . 10
Warranty coverages . . . . . . . . . . . . . . . . . . . 212
Washing matte finish paint . . . . . . . . . . . . . 185
Weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209
What happens if you wear your safety belt too
loose? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
110
What happens to unbelted occupants? . . . . 107
What impairs driving safety? . . . . . . . . . . . . . 97
Wheel bolt caps
Removing . . . . . . . . . . . . . . . . . . . . . . . . . .
193