2018 AUDI A8 spare tire

Wheel s
Occupant loading and distri­
bution for vehicle normal load
for various designated seating
capacities
Refer to the tire inflation pres­
sure
label ¢ page 293, fig . 267
for the number of seating posi­
tions . Refer to the
table¢ table
on page 295
for the number of
people that correspond to the ve­
hicle normal load .
New tires or wheels
Audi recommends having all work
on tires or wheels pe rformed by
an authorized Audi dealer or au­
thorized Audi Service Facility .
T hese facilities have the proper
knowledge and are equipped with
the required tools and replace ­
ment parts.
.,. New tires do not yet have the
optimum gripping properties. Drive carefully and at moderate
speeds fo r the first 350 miles
(500 km) with new tires .
.,. Use tires of the same construc ­
tion, size (rolling circumference)
and as close to the same tread pattern as poss ible on all four
wheels .
290
.,.Do not replace tires individually .
At least replace both tires on the
same axle at the same time.
.,. Audi recommends that you use
Audi Original Tires. If you would like to use different tires, please
note that the tires may perform
differently even if they are the
same
size¢ ,&.
.,. If you would like to equip your
vehicle with a tire/rim combina ­
tion that is different from what
was installed at the factory, con­
sult with an authorized Audi
dealer or authorized Audi Service
F acility before making a pur­
chase ~ &-
The spare tire* is different from
the regular tires installed on the
vehicle - for example, if winter
tires or wide tires are installed -
so only use the spare tire* tempo ­
rarily in case of emergency and
drive carefully while it is in use. It
should be replaced with a regular
tire as soon as possible.
All four wheels must be equipped
with tires that are the same brand and have the same construction
and tread pattern so that the
drive system is not damaged by
different tire speeds. For this rea-
son, in case of emergency, only
.,.

LL
"' .... N ,-.. N .... g :r st
use a spare tire* that is the same
circumference as the regular
tires.
&_ WARNING
-Only use tire/rim combina­ tions and suitable wheel bolts
that have been approved by
Audi. Otherwise, damage to
the vehicle and an accident
could result.
-For technical reasons, it is not
possible to use tires from oth­
er vehicles
-in some cases,
you cannot even use tires from
the same vehicle model.
-Make sure that the tires you
select have enough clearance
to the vehicle. Replacement
tires should not be chosen
simply based on the nominal
size, because tires with a dif­
ferent construction can differ greatly even if they are the
same size. If there is not
enough clearance, the tires or
the vehicle can be damaged and this can reduce driving
safety and increase the risk of
an accident.
-Only use tires that are more
than six years old when abso-
Wheels
lutely necessary and drive
carefully when doing so .
-Do not use run-flat tires on
your vehicle. Using them when
not permitted can lead to ve­
hicle damage or accidents.
-If you install wheel covers on
the vehicle, make sure they al­ low enough air circulation to
cool the brake system. If they
do not, this could increase the
risk of an accident.
Tire wear/damage
Fig. 265 T ir e profile: treadwear indica­
tor
Tire wear
Check the tires regularly for wear.
-Inflation pressure that is too low
or high can increase tire wear
considerably.
-Driving quickly through curves, rapid acceleration and heavy
braking increase tire wear.
291

This can increase the risk of an accident because it has a nega­
tive effect on handling, driving
through curves, and braking, and because it increases the risk of hydroplaning when driv­
ing through deep puddles.
Tire pressure
Fig. 266 Driver's side B -pillar : tire pres­
sur e label
- KPA. a PSI
Fig. 267 Tire pressure label
-"'
The correct tire pressure for tires
mounted in the factory and for
the spare tire* is indicated on a la­
bel. The label is located on the B­
pillar
¢ fig. 266, ¢ fig. 267.
~ When the vehicle is partially load-
N
~ ed (up to 3 peop le), use the tire
0
0
I Wheels
pressure specified for normal
Loads¢ table on page 295. If
driving the vehicle when fully loaded, you must increase the tire
pressure to the maximum speci­
fied
pressure ¢.&, .
Checking/correcting tire
pressure
.,.Check the tire pressure at least
once per month and also check it before every long drive .
.,..Always check the tire pressure
when the tires are
cold. Do not
reduce the pressure if it increas­
es when the tires are warm .
.,.Check the label¢ fig. 267 for
the correct tire pressure based on vehicle load.
.,..Correct the tire pressure if nec­
essary .
.,..Vehicles with Tire Pressure Mon­
itoring System*: store the modi­
fied tire pressure in the Infotain ­
ment system
c::> page 302.
.,.Check the pressure in the emer­
gency tire* /spare t ire*. Always
maintain the maximum temper­
ature that is specified for the
tire.
.,.
293

Wheels
under controlled conditions on a specified
government test course.
For example, a tire graded 150 would wear one
and one ha lf (11/2) times as well on the govern­
ment course as a tire graded 100 .
The relative performance of tires depends upon
the actual conditions of their use, howeve r, and
may depart significant ly from the norm due to
variations in driving habits, service practices and
differences in road characteristics and climate .
Traction
The traction grades, from highest to lowest, are
AA, A, Band
C. Those grades represent the tire's
ability to stop on wet pavement as measured un­
der contro lled conditions on specified govern­
ment test surfaces of aspha lt and concrete. A tire
marked C may have poor traction performance
¢ & .
Temperature
The temperatu re grades are A (t he highest), B ,
and C, representing the tire's resistance to the
generation of heat and its ability to dissipate
heat when tested under controlled conditions on
a specified indoor laboratory test wheel.
Sustained high temperature can cause the mate ­
rial of the tire to degenerate and reduce tire life,
and excessive temperature can lead to sudden
tire
fa ilure¢ fr:. .
The grade C corresponds to a leve l of perform ­
ance which a ll passenger car tires must meet un­
der the Federa l Motor Vehicle Safety Standard
No. 109. Grades B and A represent higher leve ls
of performance on the laboratory test wheel than
the mi nimum required by law.
A WARNING
-
The traction grade assigned to this tire is
based on straight-ahead braking traction
t ests, and does not include acceleration, cor­
nering, hydroplaning or peak traction charac­
teristics.
300
A WARNING
The temperature grade for t his tire is estab­
lished for a tire that is properly inflated and
not overloaded. Excessive speed, underinfla­
tion, or excessive loading, either separately or
in comb ination , can cause heat buildup and
possible tire failure.
A WARNING
-
-
Temperature grades apply to tires that are
properly inflated and not over or under inflat­
ed .
Tire Pressure Monitoring
System
(AS, S8)
ill General notes
Applies to: AS, 58
Each tire, including the spare (if prov ided),
shou ld be checked monthly when cold and inflat­
ed to the inflation pressure recommended by the
vehicle manufacturer on the vehicle placard or
tire inflation pressure labe l.
(If your veh icle has
tires of a different size than the size ind icated on
the ve hicle placard or tire inflat ion pressure la­
bel , you should determ ine the proper tire infla­
tion pressure for those tires).
As an added safety feature, your vehicle has been
equipped with a tire pressure mon itor ing system
(TPMS) that illum inates a low tire pressure tell­
tale when o ne or more of your tires is significant­
l y unde r-inflated. According ly, when the low tire
pressure telltale illum inates, you sho uld stop and
check your tires as soon as possible, and inflate
them to the proper pressure . Driving on a signifi ­
cant ly under -inflated tire causes the tire to over­
heat and can lead to tire fai lure. Under-inflation
also reduces fue l eff iciency and tire tread life,
and may affect the vehicle's handling and stop­ ping ability.
Please note that the TPMS is not a substitute for
proper tire maintenance, and it is the dr iver's re ­
spons ibility to maintain correct t ire pressure,
even if under-inflation has not reached the level
to trigger illumination of the TPMS low tire pres-
sure te lltale .
.,.

lL t:0 ....
"" ......
"" .... 0 0 :c ' Your vehicle has also been equipped with a TPM S
malfunction indicator to indicate when the sys­
tem is not operating properly. The TPMS mal­
function indicator is combined with the low tire
pressure telltale. When the system detects a
malfunction, the telltale will flash for approxi­
mately one minute and then remain cont inuously
illuminated . This sequence will continue upon
subsequent vehicle start-ups as long as the mal­
function ex ists.
When the malfunction indicator is illuminated,
the system may not be ab le to detect or signal
low tire pressure as intended . TPM S malfunctions
may occur for a var iety of reasons, including the
installation of replacement or alternate tires or
wheels on the vehicle that prevent the TPMS
from functioning properly. Always check the
TPMS malfunction telltale after replacing one or
more tires or wheels on your vehicle to ensure
that the replacement or alternate tires and
wheels allow the TPMS to continue to function
properly.
If the Tire Pressure Monitoring System
indicator appears
Applies to: AS, 58
The tire pressure indicator in the instrument
cluster informs you if the tire pressure is too low
or if there is a system malfunction .
Fig. 268 Instrument clus ter: indicator light with message
Using the ABS sensors, the tire pressure monitor­
ing system compares the tire tread circumfer­
ence and vibration characteristics of the individu­
al tires . If the pressure changes in one or more
tires, this is ind icated in the instrument cluster
display with an indicator light
ti] and a message .
Wheels
If only one tire is affected, the location of that
tire will be indicated.
The tire pressures must be stored in the Infotain­
ment system again each time the pressures
change (switching between partial and full load
pressure) or after changing or replacing a tire on
your vehicle
c:> page 302. The tire pressure mon i­
toring system only monitors the tire pressure you
have stored. Refer to the tire pressure label for
the recommended tire pressure for your vehicle
c:> page 293, fig . 267 .
Tire tread circumference and vibration character­
istics can change and cause a tire pressure warn­
ing if :
- the t ire pressure in one or more tires is too low
- the tire has structural damage
- the tire was replaced or the tire pressure was
changed and it was not stored
c:> page 302
- the spare tire* is installed
Indicator lights
ti] Loss of pressure in at least one tire c:> ,&..
Check the tires and replace or repair if necessary.
Check/correct the pressures of all four tires and
store the pressure again in the Infotainment sys­
tem
c:>page 302.
mm ( T ire Pressure Monitor ing System) Tire
pressure: System malfunction!. Ifm:m appears
after switching the ignition on or while driving
and the
ti] indicator light in the instrument clus­
ter blinks for approximately one minute and then
stays on, there is system malfunction. Try to
store the correct tire pressures
c:> page 302. If
the indicator light does turn off or turns on again
after a short period of time, drive to an author­
ized Audi dealer or authorized Audi Service Facili­
ty immediately to have the malfunction correct­ ed .
.&, WARNING
- If the tire pressure ind icator appears in the
display, reduce your speed immediately and
avoid any hard steering or braking maneu­
vers. Stop as soon as possible and check the
tires and their pressure.
..,.
301

Wheels
-The driver is responsible for maintaining the
correct tire pressure. You must check the
tire pressure regularly.
- Under certain conditions (such as a sporty
driving style, winter conditions or unpaved
roads), the tire pressure monitoring system
indicator may be delayed .
- Do not use run-flat tires on your vehicle. Us­
ing them when not permitted can lead to
vehicle damage or accidents .
(D Tips
- The tire pressure monitoring system can al­
so stop working when there is an ESC mal­
function .
- Using snow chains may result in a system
malfunction.
- The tires with the identification
"AO" or
"RO" ¢ page 290 have been matched with
your Audi tire pressure monitoring system.
Using these tires is recommended.
Storing tire pressures
Applies to: AB, S8
If the tire pressure changes or a tire is replaced,
it must be confirmed in the Infotainment sys­
tem .
.,. Make sure before storing that the tire pressures
of all four tir es meet the specified values and
are adapted to the
load ¢ page 291 .
.,. Switch the ignition on .
.,. Select : the ICARI function button > Car Systems
control button > Service & control > Tire pres­
sure monitor> Store tire pressure > Yes, store
now.
(D Tips
Do not store the tire pressures if snow chains
are installed. Otherwise the system could
malfunction.
302
Tire Pressure Monitoring System (SB plus)
ill General notes
Applies to: S8 plus
Each tire, including the spare (if provided),
shou ld be checked monthly when cold and inflat­
ed to the inflation pressure recommended by the
vehicle manufacturer on the vehicle placard or
tire inflation pressure label. (If your vehicle has
tires of a different size than the size ind icated on
the veh icle placard or tire inflat ion pressure la­
bel, you should determine the proper tire infla­
tion pressure for those tires).
As an added safety feature, your vehicle has been
equipped with a tire pressure mon itor ing system
(TPMS) t hat illuminates a low tire pressure tell­
ta le when o ne or more of your tires is significant­
l y under-inflated. According ly, when the low tire
pressure telltale illuminates, you should stop and
check your tires as soon as possible, and inflate
them to the proper pressure . Driving on a signifi ­
cant ly under-inflated tire causes the tire to over­
heat and can lead to tire failure . Under-inflation
also reduces fuel efficiency and tire tread life,
and may affect the vehicle's handling and stop ­
ping ability .
Please note that the TPMS is not a substitute for
proper tire maintenance, and it is the driver's re­
spons ibility to maintain correct t ire pressure,
even if under-inflation has not reached the level
to trigge r illumination of the TPM S low t ire pres­
su re te lltale.
Your vehicle has also been equipped with a TPMS
malfunction indicator to ind icate when the sys­
tem is not operating prope rly . The TPM S mal­
function indicator is combined with the low t ire
pressure telltale. When the system detects a
malfunction, the telltale will flash for approxi­
mately one minute and then remain continuously
illuminated. This sequence wi ll continue upon
subsequent vehicle start-ups as long as the mal­
function exists.
When the malfunction indicator is illuminated,
the system may not be able to detect or signal
low tire pressure as intended. TPMS
malfunctions ..,_

u. co .... N
" N .... 0 0 :c ' may occur for a variety of reasons, including the
installation of replacement or alternate tires or
wheels on the vehicle that prevent the TPMS
from functioning properly . Always check the
TPMS malfunction telltale after replacing one or
more tires or wheels on your vehicle to ensure
that the replacement or alternate tires and
wheels allow the TPMS to continue to function
properly.
Description
Applies to: 58 plus
The tire pressure monitoring system monitors
the pressure in the four tires when driving.
The system uses sensors that measure the tem ­
perature and pressure in the tires . The data is
sent from these sensors to the control module by
radio frequency.
The Tire Pressure Monitoring System shows the
current pressures and temperatures of the tires
in the Infota inment system
c:> page 303 . It also
compa res the current tire pressures with the
stored tire press ures and gives a warning in the
driver information system if the tire pressure is
different from what is stored
c:> page 304.
The system does not detect if the stored tire
pressures match the recommended tire pres­
sures.
- Every time the tire pressures change, for exam-
ple when the load in the vehicle changes,
- after replac ing a tire, or
- if wheels with new wheel sensors are used,
you must store the tire pressures again
c:> page 304.
A WARNING
-The tire pressure mon itor ing system assists
the driver in monitoring tire pressures. The
dr iver is responsible for having the tires in­
flated to the correct pressure.
- Do not change the tire pressure when the
temperature of the tire is extremely high.
T his cou ld result in serious damage to the
t ir e and even cause the tire to burst, in­
creasing the risk of an accide nt.
Wheels
-A tire with low pressure flexes more . This
heats the tire up too much. This could cause
the tread to separate and even cause the
tire to burst, increasing the risk of an acci­
dent.
- The Tire Pressure Monitoring System does
not warn you of damage or defects in the
tire construct ion that could cause the tire to
burst, for example. Inspect your tires regu­
larly.
@ For the sake of the environment
Low tire pressure increases fuel consumption
and tire wear.
(D Tips
-The pressure of the spare t ire* is not mon i­
tored.
- If tires are replaced, the sensors/va lves do
not need to be removed or replaced. Just re­
placed the valve stem and, if necessary, the
valve and the whee l electronics . If you have
questions, see an authorized Audi dealer or
authorized Audi Service Facility.
Displaying tire pressures/temperatures
Applies to: 58 plus
Requirement: the ignition must be switched on.
.. Select: the I CAR! funct ion button > Car systems
> Service & control > Tire pressure monitor >
Display tire pressure .
The current tire pressures are shown in green and
yellow numbers in the Infotainment system:
-Green: the current tire pressure and the spec i­
fied tire pressure are approx imately the same .
-Yellow: the current tire pressure is too low
compared to the specified tire pressure .
The specified tire pressure is the last tire pres ­
sure that was stored
c:> page 304 .
Note that the tire pressure also depends on the
temperature of the tire . The tire pressure in­
creases as the engine becomes warmer while
driv ing.
.,.
303

Emergency assistance
Emergency assistance
General information
.,. Park the vehicle as far as possible from moving
traffic in the event of a breakdown. In the event
of a flat tire, park the vehicle on a level surface .
It you are on a steep hill, be especially careful.
.,. Set the parking brake .
.,. Switch the emergency flashers on .
.,. Set up the warning triangle r=;,page 312 .
.,. Have the passengers exit the vehicle . They
should move to a safe place, for example be­
hind a guard rail.
A WARNING
Follow the steps given above. This is for your
protection and the for the safety of other driv­
ers.
Equipment
Warning triangle
Applies to: vehicles with warning triangle
Fig. 270 L uggage co mpartm ent lid : w arnin g triangle
The warning triangle placed in the vehicle at the
factory is located in the luggage compartment.
.,. To remove the warning triangle, press the fas-
tener in the direction of the arrow and fold the
holder down.
The luggage compartment lid is only designed to
hold the warning triangle offered by the Audi
Genuine Accessories program.
312
Vehicle tool kit
Applies to: vehicles with vehicle toot kit
Fig. 271 Lu gg age compartment : cargo floor cove r folded
upward
Fig. 272 Luggage compartment: examp le of vehicle toot
kit and vehicle j ack
The vehicle tools and vehicle jack* are stored in
the luggage compartment under the floor cover .
.,. Lift the cargo floor by the plastic handle .
.,. Hook the handle into the luggage compartment
seal
r:;, fig. 2 71 .
.,. Turn the handwheel counter-clockwise and re ­
move it .
.,. Remove the spare tire* to access the vehicle
tool kit
~ fig. 271 .
Depending on the equipment , the veh icle tool kit
may be located under the spare tire, under an­
other cover or in the tool box.
The position of the vehicle jack* may vary .
A WARNING
Improper use of the veh icle jack can cause se­
rious personal injuries.
-Never use the screw driver hex head to
tighten wheel bolts, since the bolts cannot
attain the necessary tightening torque if you
..,.