2018 AUDI A6 light

a co .... N
" N .... 0 0 \,;J ' avoid scratches, move the scraper only in
one direction and not back and forth.
- N ever remove snow or ice from door win­
dows and mirrors using warm or hot water
because this could cause cracks to form .
- To avoid damage to the rear w indow de ­
fogger, do not apply any stickers on the heating wires on the inside of the window .
-Deco rati ve parts /trim
- Never use chrome care or cleaning prod-
ucts.
- Paint
-To red uce the risk of scratches, the vehicle
must be free of dirt and dus t before pol­
ishing or waxing .
- To preven t pa int damage, do not pol ish or
wax the ve hicle in direct sunlight.
- To red uce the risk of pa int damage, do not
polish away rust spots.
- Remove cosmetics and sunscreen immedi­
a tely- these could damage the pa int.
- Displa ys
- To avoid scratches, do not use dry cleaning
methods on displays .
-Controls
- Make sure that no fluids enter the con-
trols, because this could cause damage.
- Safet y belts
- Do not remove the safety belts to clean
t hem.
- Never clean safety belts or their compo­
nents chemically or with cor rosive fl uids
or so lvents and neve r allow sh arp obje cts
t o come into con ta ct w ith the sa fe ty belts.
Th is could cause damage to the belt web ­
bing .
- If the re is damage to the webbing, the
connections, the retractors or the b uckles,
have them replaced by an authorized Audi
dea ler or authorized Audi Service Facility.
- Te xtiles/artificial leather / Alcantara
- Never treat artific ial leather/ Alcantara
w ith leather care products, solvents, floor
polish, shoe polish, spot remove or similar
prod ucts .
- Have a specialist remove st ubborn stains
to prevent damage.
Care and cleaning
- Neve r use steam cleaners, brushes, hard
sponges, etc. when cleaning .
- Do not turn on the seat heating* to dry the
seat.
- Obje cts w ith sharp edges, such as zippe rs
or rivets on clothing or be lts, can cause
damage to the surface .
- Open hoo k and loop fasteners, for exam­
p le on clothing, can damage seat covers.
M ake sure hook and loop fasteners are
closed.
- Natural leather
- Never treat leather with solvents, floor
polish, shoe po lish, spot remover or sim i­
lar p roducts.
- Objects w ith sharp edges, such as zippers
or rivets on clothing or belts, can cause
damage to the surface.
- Never use steam cleaners, brushes, hard
sponges, etc. when cleaning.
- Do not turn on the seat heating* to dry the seat.
- To he lp prevent the leather from fad ing,
do not leave the vehicle in direct sun light
fo r long pe riods of time. If leav ing the ve­
h icle parked fo r long pe riods of time, you
should cover the le athe r to prote ct it from
d irec t sun light.
(D Tips
- Insects are easie r to remove from paint that
has been freshly waxed.
- Regular wax ing can prevent rust spots from
forming.
Placing your vehicle out
of service
If you would like to take your vehicle out of serv ­
ice for a longer period of time, contact an author­
ized Audi dea ler or authorized Audi Service Facili ­
ty. They will adv ise you of important measures,
such as corrosion protection, service and storage
procedures. Also follow the information about
the veh icle battery
r=;,page 197 .
225

a co .... N
" N .... 0 0 \.J ' (D Tips
The vehicle jack* in your vehicle is mainte­
na nee-free.
Replacing wheels
Before changing a wheel
Observe the following precautions for your own
and your passenger's safety when changing a
wheel .
'"After you experience a tire failure, pull the car
well away from moving traff ic and try to reach
le ve l ground before you stop ¢,&. .
'"All passe ngers should le ave the car and move
to a safe location (for instance, be hind the
guardra il) ¢ ,&. .
.. Engage the parkin g brake to p revent your vehi ­
cle from rolling
unintentionally ¢,&. .
'"Move selecto r lev er to p osition P ¢ ,&. .
'"If you are towing a trailer, unh itch the trailer
from your veh icle.
'" Take the jac k and the sp are tir e* out of the lug­
gage compartment
i::> page 226 .
A WARNING
You or your passengers cou ld be inju red w hile
chang ing a wheel if you do not follow these
safety precautions :
- If you have a flat t ire, move a safe distance
off t he road. Tur n off the engine, t urn the
emergency flashers on and use other warn ­
ing devices to alert other motorists .
- Make s ure tha t pa ssengers w ait in a sa fe
place away from the vehicle and we ll away
from the road and traffic.
- T o help prevent the vehicle from moving
sudden ly and possibly slipping o ff th e jack,
always fully set the parking brake and b lock
the front and back of the wheel diagonally opposite the wheel be ing changed. When
one front whee l is lifted off the ground,
placing the Automatic Transm ission in P
(Park) w ill
not prevent the veh icle from
moving.
Em ergenc y ass is tanc e
-Before you change a whee l, be sure the
ground is level and firm . If necessary, use a
sturdy board under the jack.
- Always store the vehicle too l kit, the jack
and the replaced tire in the luggage com­
partment
¢ page 130.
(D Tips
Before changing the wheel, you must activate
the jacking mode, so that the automatic con­
tro ls for the Adaptive Air Suspension* do not
make it more difficult to lift the vehicle with
the
jack ¢ page 229 .
Changing a wheel
When you change a wheel , follow the sequence
described below step-by-step and in exactly that
order .
l. Activate the vehicle jack mode* ¢ page 229.
2. Remove the deco rati ve wheel co ver* or the
wheel bolt c aps *. For more details see also
¢ page 228, Decorative wheel covers or
¢ page 228, Wheels with wheel bolt caps .
3. Loosen the wheel bolt s ¢page 229.
4. Locate t he p roper mount ing point for the
jack and align the jack be low that poin t
¢page 229 .
S. R ais e the car with the jack ¢ page 229 .
6. Remove the wheel with the fl at tir e and then
install
the spare ¢ page 231.
7. Tig hte n all wheel bolts lightly .
8 .
Lower the vehicle with the jack .
9 . Use the wheel bolt wrench and
firml y tighten
all wheel
bo lts ¢ page 229.
10. Replace t he decorat ive wh eel cover * or the
wheel bolt cap s*.
11. Deactivate the vehicle jack mode* in t he
MMI :
ICAR I function button > (Car )* sys tem s
contro l button > Ser vicing & che cks > Air
s usp.: jack mod e> Off.
The vehicle jack mode * switches off automatica l-
ly at speeds abov e 6 mph (10 km/h).
.,.
227

a co ,...,
N
" N ,...,
0 0 \,;J ' Taking the wheel off/installing the spare
Follow these instructions step-by-step for chang­
ing the wheel .
Fig. 198 Changing a wheel: us ing the screwdriver hahd le
(with the blade removed} to turn the bolts
F ig. 199 C h ang ing a whee l: alig nme nt pin ins ide the top
hole
Afte r you have loosened all wheel bolts and
raised the vehicle off the ground, remove and re­
p lace the whee l as follows:
Removing th e wheel
.,. Use the hexagon al so cket in the screwdri ver
handle
to completely remove the topmost
whee l bolt and set it aside on a
clean surface
¢ fig. 198 .
... Screw the threaded end of the alignment pin
from the tool k it hand-tight into the empty bolt
hole¢ fig. 199 .
... Then remove the other wheel bolts as described
above .
... Take off the wheel leaving the a lignment pin in
the bolt ho le
¢ 0.
Putting on the spa re wh eel
... Lift the spare wheel and carefully slide it over
the alignment pin to guide it in place
¢ 0 .
Em ergen cy as sis tanc e
... Use the hexagonal socket in the screwdr iver
handle to screw in and tighten all wheel bolts
slightly.
... Remove the alignment pin and insert and t ight­
en the remaining wheel bo lt slight ly like the
rest .
.,. Turn the jack handle counter-clockw ise to lower
the vehicle unt il the jack is fully released .
.,. Use the wheel bolt wrench to tighten a ll wheel
bolts
firmly¢ page 229. Tighten them cross­
wise,
from one bo lt to the (approx imately) op­
posite one, to keep the wheel centered.
(D Note
When removing o r installing the wheel, the
rim could h it the brake rotor and damage t he
rotor . Work carefully and have a second per­
son help you .
(D Tips
Never use the hexagonal socket in the hand le
of the screwdrive r to loosen or t ighten the
whee l bolts.
- Pull the reversible blade from the screwdriv ­
er before you use the hexagona l socket in
the handle to turn the whee l bolts.
- When mounting tires with
unidirect ional
tread de sign
make sure the tread pattern is
pointed the right
way ¢ page 231 .
-The wheel bolts shou ld be clean and easy to
t u rn. Check for dirt and corrosion on the
mating surfaces of both the wheel and the
hub. Remove all dirt from these surfaces be­
fore remounting the wheel.
Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tread pattern pointed in the
right direction .
Using a spare t ire w ith a tread patte rn
in tended for u se in a specific direction
When using a spare tire w ith a tread pattern in­
tended for use in a specific direction, please note
the following:
- The direction of rotation is marked by an arrow
on the side of the tire.
""
2 31

a co ,...,
N
" N ,...,
0 0 \,;J ' Driver side cockpit fuse
assignment
F ig. 202 Drive r side cockp it : fuse panel w it h plastic bracket
Fuse panel @ ( black)
No . Equipment
Electromechan ica l powe r stee ring, trailer
1 hitch, ionizer, switch st
rip, seat heating
(rear), electromechan ica l park ing brake
Ho rn, climate con trol system, Gateway,
2 au
tomati c dimm ing in ter ior rearv iew m ir-
ro r, On -Board Unit
4 Park ing aid, headlight range adjustment
5
Dynamic steering, electronic stabilization
control (ESC)
6 Headlights
7 Adapt ive cru ise control
8 Front passenger's seat senso rs, a irbag
9 Gateway
10 Engine sound, nig
ht vision ass ist, garage
door opene r (H ome link), parki ng aid
11 Video camera
image processi ng
12 Headlights
13 Steering column sw
itch module
Fuses
Fuse panel @ (black)
14 Termina l 15 (luggage compartment)
1 5 Starte r
Fuse panel @ (brown)
No . Equipment
1 Infotainment system
2 Infot ainment system
3 Front passenger's seat
5
A
ir bag, e lec tronic sta bi liz ation con trol
( E SC)
6 Ant
i- theft alarm system
7 E lectromec ha nical pa rking brake
8 Inter io r li ghts
9
Windshie ld video came ra heating, light/
r ain sensor
10 Lumbar support (dr iver's se at)
11 Driver
's seat
12 Electronic stab ilizati on con trol
13 Horn
1 4 Head lights
lS Front seat heating
16 Dynamic s tee ring
Fuse panel © (red)
No . Equipment
1 Clutch peda l
2 Fuel p ump
3 Brake
light sensor
4 Engine acoustics
5 Rear door
6 Fr
ont door
7 Elec tronic stab iliza tion control
8 Windshie ld wiper motor
9 H ead light washer system
10 Interio
r light ing, climate control system
1 1 Head lights
12 Sunroof
235

Fuses
Front passenger side
cockpit fuse assignment
F ig . 203 Front passenger side cockpit: fuse pane l with
plastic bracket
Fuse panel @ (red )
No. Equipm ent
1 Infotainment, CD changer
2 I
nfotainment (display)
Fuse panel@ (brown)
No . Equipm ent
1 Climate control system
2 Climate
control sys tem (blowe r)
3 Diagnostic interface
4 Ele ct ric al ignit ion lock
5 Electronic steer ing column lock
6 Steering column sw itch module
7 Power stee ring co lumn adjustment
8 Light switch
9 Head-up display
10 I
nstrument cl uste r
11 Infota inment, DVD changer
236
Luggage compartment
fuse assignment
F ig . 2 04 L uggage compartment: fuse panel with plast ic
b racket
Fuse panel @ (black)
No . Equipment
1 Tra
iler hitch/220 volt socket
2 Tra ile r hitc h/climatized cup holder
3
Trailer hitch/adjusting front passenger's
seat from the rear
4 E lec tromechani cal pa rking brake
5 Electromechanical parking brake
6 Fr on t door (front passenger's side)
7 Rear exterior lighting
8 Central locking, closing aid
9 Seat heating (fro nt)
11 Seat
heating (rear), climate control system
(rear)
12 Tra ile r hitch, gateway (e-tron)
Fuse panel @ (red)
No . Equipment
1 Left safety
belt tensioner
2 R ight safety be lt tens ioner
3 Fuel pump
4 Eng ine moun t
5
Sensor-controlled luggage compartment
l id
6 Air s uspension, adaptive dampers
7 Rear door (front passenger's side)
8 Tail lights
9 Luggage compartmen t lid

Bulbs
Bulbs
Replacing light bulbs
For your safety, we recommend that you have
your authori zed Audi dealer replace burned out
bulbs for you.
It is becoming increasingly more and more diffi ­
cult to replace vehicle light bulbs since in many
cases, other parts of the car must first be re­ moved before you are able to get to the bulb.
This applies espec ially to the light bulbs in the
front of your car wh ich you can only reach
through the eng ine compartment.
Sheet metal and bulb holders can have sharp
edges that can cause ser ious cuts, and parts
must be correctly taken apart and then properly
put back together to help prevent breakage of
parts and long term damage from water that ca n
ente r housings that have not been properly re­
sealed.
For your safety, we recommend that you have
your author ized Audi dealer replace any bulbs for
you, s ince your dealer has the proper tools, th e
correct bulbs and the expertise .
Gas discharge lamps (Xenon lights):
Due to the high electrical voltage, have the bulbs
replaced by a qualified technic ian . Headlights
with Xenon light can be identified by the high
voltage sticker.
LED headlights*
LED headlights require no maintenance. Please
contact your authorized Audi dealer if a bulb needs to be replaced.
A WARNING
Contact w ith high-voltage components of the
electrical system and improper replacement
of gas d ischarge (Xenon) headl ight bulbs can
cause se rious personal injury and death.
- Xenon bulbs are pressurized and can ex­
plode when be ing changed .
- Chang ing Xenon lamps requires the spec ial
train ing, instructions and equipment .
238
-On ly an authorized Audi dealer or other
qualif ied workshop should change the bu lbs
in gas discharge lamps.
A WARNING
There are parts with sharp edges on the open­
ings and on the bulb holders that can cause
serious cuts .
- If you are uncertain about what to do, have
the work performed by an author ized Audi
dealer or other qualified workshop . Ser ious
pe rsonal injury may res ult from improperly
pe rformed wor k.
(D Tips
- If you still prefer to replace the light bulbs
yourself, be aware that the engine compart­
ment is a hazardous area to wo rk in
~page 189 ~.&.
-It is best to ask your authorized Audi dea ler
w henever you need to change a bulb.

a co .... N
" N .... 0 0 \.J ' Emergency situations
General
This chapter is intended for trained emergency
crews and working personnel who have the nec­
essary tools and equipment to perform these
operations.
Starting by pushing or
towing
~ Note
Vehicles with an automatic transmission can­
not be started by pushing or towing.
Starting with jumper
cables
If necessary, the engine can be started by con­
necting it to the battery of another vehicle .
If the engine should fail to start because of a dis­
charged or weak battery, the battery can be con­
nected to the battery of
another vehicle, using a
pair of jumper cables to start the engine.
Jumper cables
Use only jumper cables of sufficiently large cross
section
to carry the starter current safely. Refer
to the manufacturer's specifications.
Use only jumper cables with
insulated terminal
clamps which are distinctly marked :
plus(+) cable in most cases colored red
minus(-) cable
in most cases colored black.
A WARNING -
Batteries contain electricity, acid, and gas.
Any of these can cause very serious or fatal in­
jury. Follow the instructions below for safe
handling of your vehicle's battery .
-Always shield your eyes and avoid leaning
over the battery whenever possible.
-A dead battery can freeze at temperatures
around 32 °F (0 °C) . If the vehicle battery is
frozen, you must thaw it before connecting
the jump start cables. If you do not, this in-
Emergency situations
creases the risk of an explosion and chemi­
cal burns. After jump starting the vehicle,
drive to an authorized Audi dealer or author­ ized Audi Service Facility immediately to
have the vehicle battery checked.
- Do not allow battery acid to contact eyes or
skin . Flush any contacted area with water
immediately.
- Improper use of a booster battery to start a
vehicle may cause an explosion .
- Vehicle batteries generate explosive gases .
Keep sparks, flame and lighted cigarettes
away from batteries.
- Do not try to jump start any vehicle with a
low acid level in the battery .
- The voltage of the booster battery must also
have a 12-volt rating . The capacity (Ah) of
the booster battery should not be lower
than that of the discharged battery. Use of
batteries of different voltage or substantial­
ly different "Ah " rating may cause an explo­
sion and personal injury.
- Never charge a frozen battery. Gas trapped
in the ice may cause an explosion.
- Never charge or use a battery that has been
frozen. The battery case may have be weak­
ened.
- Use of batteries of different voltage or sub­
stantially different capacity (Ah) rating may
cause an explosion and injury. The capacity
(Ah) of the booster battery should not be
lower than that of the discharged battery.
- Before you check anything in the engine
compartment, always read and heed all
WARNINGS
c>page 189.
@ Note
- Applying a higher voltage booster battery
will cause expensive damage to sensitive
electronic components, such as control
units, relays, radio, etc.
- There must be no electrical contact between
the vehicles as otherwise current could al­
ready start to flow as soon as the positive
( + ) terminals are connected.
239

Emergency situations
@ Tips
The discharged battery must be properly con­
nected to the vehicle's electrical system .
When jump starting or charging the battery,
never connect the negative ground cable to
the battery negative post because the battery
manager system must be able to detect the
battery's state of charge. Always connect the
negat ive g round cable to the negative ground
post of the battery manager control unit.
Use of jumper cables
Make sure to connect the jumper cable clamps in
exactly the order described below!
Fig . 205 Engine compartmen t: connecto rs for jump start
cables and charger
@
F ig . 206 Jump starting w it h the battery of anot her vehicle :
@-booster battery, @- discha rged vehicle battery
The procedure described below for connecting
jumper cables is intended to provide a jump start
for your veh icle.
Vehicle with discharged battery:
• Turn off lights and accessories, move lever of
automatic transmission to N (Neutral) or P (Park) and set park ing brake.
240
Connect POSITIVE(+) to POSITIVE(+) (red)
• Open the red cover on the positive terminal
i:!.> fig. 205.
1. Connect one end of the red positive cable on
the
jump start bolt ~ fig. 206@ (bolt under
the red cover= "positive") of the vehicle to be
started @.
2. Connect the other end to the positive termi-
nal @of the booster battery @.
Connect NEGATIVE(-) to NEGATIVE(-)
(black)
3. Connect one end of the black negative cable
to the negative terminal @ of the booster
battery @.
4. Connec t the other end to the
jump start pin
@ (bolts with hex head bolt= "negative") of
the vehicle to be started @.
Starting the engine
• Start the eng ine of the vehicle with the booster
battery @. Run the eng ine at a moderate
speed.
• Sta rt engine w ith discharged vehicle battery@
in the usual manner.
• If the engine fails to start, do not keep the
starter cranking for longer than 10 seconds.
Wait for about 30 seconds and then try again.
• With engine running, remove jumper cables
from both veh icles in the exact
reverse order.
• Close the red cover on the pos itive terminal.
The battery is vented to the outside to prevent
gases from entering the vehicle interior . Make
sure that the jumper clamps are well connected
with their metal parts in full contact w ith the
battery terminals.
A WARNING
To avoid serious personal injury and damage
to the vehicle, heed all warnings and instruc­
tions of the jumper cable manufacturer. If in
doubt, call for road service .
- Jumper cables must be long enough so that
the vehicles do not touch.
- When connecting jumper cables, make sur e
that they cannot get caug ht in any moving
pa rts in the engine compartment.
.,.