2018 AUDI A5 COUPE lock

,&_ WAR NING
California Proposition 65 Warning:
- Engine exhaust, some of its constituents,
and certain vehicle components contain or
emit chemicals known to the State of Cali­
fornia to cause cancer and birth defects and reproduct ive harm. In addition, certain flu­
ids contained in vehicles and certain prod­
ucts of component wear contain or emit
chem icals known to the State of California
to cause cancer and birth defects or other reproduct ive harm.
- Battery posts, terminals and related acces­ sories contain lead and lead compounds,
chem icals known to the State of California
to cause cancer and reproduct ive harms.
Wash hands after handling.
(D Note
When filling flu ids, be sure not to mix the flu­
ids up . Otherwise severe ma lf u nctions and en­
gine damage w ill occur.
@) For the sake of the environment
You shou ld regularly check the ground under
your vehicle in o rder to detect leaks qu ickly .
If
there a re visible spots from oil or other fluids,
bring your vehicle to an authorized Aud i dea l­
er or authorized Audi Service Facility to be
checked.
Opening and closing the hood
The hood is released from inside the vehicle.
Fig. 274 Driver footwell: release leve r
Checki ng an d Fill in g
Fig. 275 Unlocked hood : lever
Make sure the wiper arms are not raised up from
the windshield. Otherwise the paint could be damaged .
Opening the hood
" With the driver's doo r open, pull the lever be­
low the instrument panel in the direction of the
arrow
r:;, fig . 2 7 4.
" Ra ise the hood slightly ¢.&_ .
"Press the lever ¢ fig. 275 in the direct ion of the
arrow. This releases the hooks .
"Open the hood .
Closing the hood
" Push the hood down until you override the
force of the str uts.
" Let the hood fall lightly into the latch . Do not
press it
in. ¢ .&_ .
A WARNING ,..___
-Never open the hood when there is steam or
coo lant escaping from the engine compart ­
ment, because there is a risk that you could
be burned. Wait until no steam or coolant is
escaping.
- For safety reasons, the hood must always be
closed securely while driv ing. Because of
this, always check the hood after closing it
to make sure it is latched correctly . The
hood is latched if the front corners cannot
be lifted.
- I f you notice that the hood is not latched
while you are d riving, s top immed iately and
close it, because driving when the hood is not latched increases the r isk of an accident . .._
331

Wheels
@ For the sake of the environment
Reinstall su mmer tires at the appropriate
time, because they pro vide better handling
when roads are free of snow and ice. Summer tires cause less road noise, tire wear and fuel
consumption.
@ Tips
You can also use all season tires instead of
w inter t ires. Please note that in some coun­
tries where w inter tires are required, only
w inter t ires with the
& symbol may be per­
m itted.
Snow chains
Snow chains not only imp rove the dr iving in w in ­
ter ro ad conditions, b ut also the brak ing .
.,. Only install snow chains o n the front wheels .
.,. Check and cor rect the seating of the snow
c h ains after dr iv ing a few feet, if ne cessa ry . Fo l­
low the ins tructions from the m anufactu rer.
.,. Note the maximum permit ted speed when driv ­
ing with snow chains. Do not exceed 30 mp h
(SO km/h) .
Use of snow chains is o nly pe rmitted with certain
rim/tire combinations due to technical reasons .
Check with an authorized A udi dealer or author­
ized Audi Service Fac ility to see if you may use
snow chains.
Use fine-mesh snow chain s. They must not add
more t han 0.53 in (13 .5 mm) in height, includ ing
the chain lock .
You mus t remove the snow chains on roads w it h­
out snow . Otherwise, you could impai r dr iving
abi lity and damage the tires .
A WARNING
Us ing inco rrect snow chains or insta lling snow
chains incorrectly can result in loss of vehicle
control, which increases t he risk of an acc i­
dent .
358
(D Note
Snow chains can damage the rims/whee l cov ­
ers * if the c ha ins come into direct contact
with them . Remove the whee l cove rs* first.
Use coated snow chains.
(D Tips
When using snow chains, it may be usefu l to
switch on sport mode
r=> page 152.
Low-profile tires
App lies to: vehicles with low-profi le tires
Your vehicle is equipped with low-profile t ires* at
the factory. Compared to other tire/r im combina­
t ions, low-profi le tires offer a w ider t read surface
and a la rger r im diamete r with shorter tire side­
walls. This results in an agile dr iv ing style. How­
ever, i t may reduce the leve l of com fort and in ­
crease road noise whe n driving on roads in poo r
condition .
Low-p rofile ti res ca n become damaged mo re
q uickl y than st andar d tires when dr iv ing ove r
l a rge bumps, potholes, manhole covers, speed
b u mps and curbs . Therefore, it is particularly im ­
portant to maintain the correct tire pressure
r::> page 3 51.
To reduce the risk of damage to the tires and
rims, drive very caref ully on poor roads.
Check your wheels regu larly eve ry 2,000 m i
( 3 ,00 0 km) for d amage. For ex am ple, c heck for
bulges/crac ks on the tires or deformations/
c racks on the rims.
Af ter a heavy imp act o r damage, have the tires
and rims i nspected or replaced immedia tely by
an a uthorized Audi dea le r or authorized Audi
Service Facility .
Low-p rofile ti res c an wear out f aster than stand­
a rd tires.
Summer tires are not suitable fo r cold weather,
snow or black ice. If yo u are d rivi ng in these con­
d it ions, use wi nter or a ll season tires
r=> page 357.

Care and cleaning
Component Situation Solution
Wh eels
Road salt Water
Brake dust Acid-free special cleaning solution
Ex h aust t ail pipe s Road salt Water, cleaning solution su itab le for stainless steel, if nee-
essary
P ower top Deposi ts Clea n water, powe r top cleaning prod uct, if necessa ry.
C lean with the grain of the fabric using a soft brush and al-
l ow to air dry.
Wind d eflect or Deposits Water, mild soap solut ion, if necessaryal
Dec orat ive part s/ Deposits Mild soap so
lution al, a cleaning so lution suitable for stain-
trim less stee l, if necessary
Paint Pai nt damage Refer to the paint numbe r o n the veh icle data label, repair
with tou ch up
pa int~ page 386
Spilled fuel Rinse with water immediately
Surface r ust Rust remover, then pro tect w ith hard wax; for questions,
consult an authorized A udi dealer or authorized Audi Serv -
ice Facility .
Corros ion Have it removed by an authorized Aud i dealer or a uthor-
ized Audi Service Fac ility.
Water no longer Protect with hard wax (at least twice per year)
beads on the surface
of clean paint
No shine even though Treat with suitable po lish; then apply paint prote ctant if
paint has been pro- the polish that was used does not contain any protectant
tected/paint looks
poor
Deposits such as in- Dampen w ith wate r immediately and remove w it h a micro-
sects, bird dropp ings, f iber cloth
t ree sap and road salt
Grease-based con-Remove immediately with a mild soap solution al and a
tam inants such as soft cloth
cosmetics or sunb lock
Ca rbon p art s Deposits Interior:
clean the same way as plastic parts
Exterior: clean the same way as painted parts
Dec orativ e decal s Deposits Soft sponge with a mild soap so lutional
a) Mild soap solut ion: max im um two tablespoons of neutral soap in 1 quart Cl liter) of water
Interior cleaning
Component Situation Solution
Window gla ss
Deposits Glass cleaner, then wipe dry
D
ecorat iv e part s/ Deposits Mild soap solutional
trim
36 4
...

Emergency assistance
Emergency assistance
General information
.,. Park the vehicle as far as possible from moving
traffic in the event of a breakdown. In the event
of a flat tire, park the vehicle on a level surface .
It you are on a steep hill, be especially careful.
.,. Set the parking brake .
.,. Switch the emergency flashers on .
.,. Have the passengers exit the vehicle . They
should move to a safe place, for example be­
hind a guard rail.
_& WARNING
Follow the steps given above . This is for your
protection and the for the safety of other driv ­
ers.
Equipment
Vehicle tool kit/tire mobility kit/vehicle
jack
App lies to: veh icles with the vehicle tool kit, tire mobility kit
and veh icle jack
Fig. 286 Luggage compartment: veh icle tool kit, vehicle
j ack, tire mobil ity kit and compressor
The vehicle tool kit, vehicle jack, tire mobility kit
and compressor are stored in the luggage com­
pa rtm ent under the cargo floor cover.
Applies to: Coupe/Cab riolet
.,. Lift the cargo floor using the plastic handle and
hook the handle onto the luggage compart­
ment seal or above the power top storage com­
partment.
368
App lies to : Sportback
.,. Fold the cargo floor cover up or remove it com­
pletely .
Applies to: vehicles with spare tire
.,. Remove the handle by turning it counter-clock­
w ise and remove the spare tire.
App lies to: Coupe/Cabr io let
.,. Unhook the cargo floor before closing the lug -
gage compartment lid.
Depending on vehicle equipment, the vehicle tool
kit, tire mobility kit and compressor may be lo­
cated under another cover that is secured with a handwheel.
Applies to: Cabriolet
The vehicle jack is located unde r the foam piece.
To remove the foam piece, you must remove the
wind deflector*, the compressor securing strap*
and the hand wheel.
_& WARNING
Improper use of the veh icle jack can cause se­
rious personal injuries.
- Never use the screw driver hex head to
tighten wheel bolts, since the bolts cannot attain the necessary tightening torque if you
use the hex head, potentially causing an ac­
cident.
- The factory-suppl ied jack is intended only
for your veh icle model. Under no circum­
stances should it be used to lift heavy
veh icles or othe r loads; you risk injuring
yourse lf.
- Never start the engine when the ve hicle is
raised, which could cause an accident.
- Support the vehicle securely with appropri­
ate stands if work is to be performed under­
neath the vehicle; otherwise, there is a po­
tential risk for in jury .
- Never use the jack supplied with your Aud i
on another vehicle, particularly on a heavier
one. The jack is only suitable for use on the
vehicle it came with.
~

-If the t ire is too severely damaged , see an
authorized Aud i dealer or authorized Aud i
Service Facility for assistance .
@ For the sake of the environment
You can give the used tire sealant bottle to an
author ized Audi dealer or authorized A udi
Serv ice Facility for disposal.
@ Tips
Remember to obtain a new bottle of sea lant
from an authorized Audi dea ler or authorized
Audi Service Facility after repair ing a tire.
Replacing a wheel
Preparation
You must complete the preparation before
changing a tire .
.,. Read and follow the important safety precau­
tions ~ page 368 .
.,. Set the parking brake .
Applies to: ve hicles with man ua l transmiss ion
.,. Shift in to 1st gear.
Applies to: ve hicles with automat ic t ra n smi ssio ns
.,. Select the P selector leve r pos ition .
.,. When towing a trailer: disconnect the tra iler
from your veh icle .
.,. Lay out the veh icle tool kit 9 page 368 and the
spare tire
~ page 375 .
.,. Switch the ignition off .
A WARNING
When using the vehicle jack* on a road with a
steep hill or offroad, you must take extra pre­
cautions to prevent the vehicle from rolling .
Use suitab le objects to b lock the front and
back of the wheel that is diagonal from the
wheel with the flat tire.
A WARNING
You or your passengers could be in ju red wh ile
chang ing a wheel if you do not follow these
safety precautions :
Emergen cy a ssis tanc e
-If you have a flat tire, move a safe distance
off the road. Turn off the eng ine, turn the
emergency flashers on and use other warn­
ing dev ices to alert other motorists .
- Make sure that passengers wait in a safe
place away from the vehicle and well away
from the road and traff ic .
- To help prevent the veh icle from moving
suddenly a nd possib ly slipping off the jack*,
always fully set the park ing brake and block
the front and back of the wheel diagonally opposite the wheel being changed. When
one front wheel is lif ted off the gro und,
p la cing the Automa tic Transmission in P
(Park) will
not prevent the vehicle from
moving.
- Before you change a wheel, be sure the
g ro und is leve l and firm. If necessary, use a
sturdy board under the jack *.
- Always store the vehicle tool kit, the jack *
a nd the replaced tire in the luggage com­
partment
~ page 263 .
(D Tips
Obey all laws .
Removing the caps
Fig. 290 W hee l: whee l bolt s w ith ca ps
.,. Slide the p lastic clip (from the veh icle tool k it)
on to the cap unt il it
engages ~ fig. 290.
.,. Remove the cap with the p lastic clip.
371

Fuse assignment - Driver's side of the
cockpit
F ig. 300 D riv er s ide cockpit: fuse panel wit h plastic bracket
Fuse panel
No . Equipment
2 Telephone
4 Head-up display
5 Audi music interface, USB charging port
6 Front climate control system contro ls
7 Steering column lock
8 Infotainment system display
9 Instrument cluster
10 Info tainment un it
11 Light switch
12 Steering column electronics
14 Infotainmen t system
16 Steering wheel heating
Fuses and bulbs
Fuse assignment - Left side of the luggage
compartment
Fig. 301 L eft side of the l uggage compartment: fuse panel
wi th plastic cl ip
Fuse panel @ (black)
No . Equipment
2 Windshield defroster
3 W indshie ld defroster
5 Suspens ion control
6 Automat ic transmission
7 Rear window
defogger
8 Rear sea t heating
9 Tail lights
10 Left safety belt tens ioner
11 Central locking system
12
Power luggage compartment lid, left neck
heating
Fuse panel @ (red)
No. Equipment
Not assigned
Fuse panel © (brown)
No . Equipment
2 Telephone, safety belt micropho ne
379

-When connecting jumper cables, make sure
that they cannot get caught in any moving
parts in the engine compartment.
- Do not bend over the batteries
-danger of
chem ical burns!
- The battery cell locking screws must be
tightened securely.
- Before you check anything in the engine
compartment, always read and heed all
WARNINGS
c!.> page 330.
(D Note
Improper hook-up of jumper cables can ruin
the generator.
- Always connect POSITIVE(+) to POSITIVE
( + ), and NEGATIVE(-) to NEGATIVE(-)
ground post of the battery manager contro l
unit.
- Check that all screw p lugs on the battery
cells are screwed in firmly. If not, tighten
plugs prior to connecting clamp on negative
battery terminal.
- Please note that the procedure for connect­
i ng a jumper cable as described above ap­
plies specifically to the case of your vehicle
being jump started. When you are giv ing a
jump start to another vehicle, do
not con­
nect the negative (-) cab le to the negative
(-) terminal on the discharged battery @
c!.> fig. 303. Instead, securely connect the
negative (-) cable to either a solid me tal
component that is firm ly bolted to the en­
gine block or to the engine bloc k itself. If
the battery that is be ing charged does not
vent to the outs ide, escaping battery gas
could ignite and explode!
Towing with a tow truck
General hints
Your Audi requires special handling for towing .
The following information is to be used by com ­
mercial tow truck operators who know how to op­
erate their equipment safely.
-Never tow your Audi, towing will cause dam­
age to the engine and transmission .
Emergency situations
-Never wrap the safety chains or winch cables
around the brake lines .
- To prevent unnecessar y damage, your Audi
must be transported with a flat bed truck.
- To load the vehicle on to the flat bed , use the
towing loop found in the vehicle tools and at­
tach to the front or rear anchorage
¢ page 383 and ¢ page 384 .
A WARNING
--
A vehicle being towed is not safe for passen­
gers. Never allow anyone to ride in a vehicle
being towed, for any reason.
Front towing loop
Only install the front towing loop when it is
needed.
Fig . 304 Front bumper : in sta lling the towing loop
The threaded opening for the towing loop is lo­
cated on the right side of the front bumper.
.. Remove the towing loop from the vehicle too l
kit
¢ page 368 .
.. Press the cap inward with brief, forceful pres­
sure
c!.>fig. 304 . The cap will loosen from the
bumper .
.. Insert the towing loop a ll the way into the
threaded opening and tighten it with a wheel
wrench.
.. After using, place the towing loop back in the
veh icle tool kit.
A WARNING
'"' -
If the towing loop is not tightened until it
stops when installing, the threads may be
pulled out when towing the vehicle and that
could cause an accident.
383

<( a, .... N ,....
N .... 0 \0
3 a,
If you must lift your vehicle with a floor jack to
work underneath , be sure the vehicle is safely
supported on stands intended for this purpose .
Front lifting point
The lifting p oint is loc ated on the floo r pan rein­
fo rcement abou t at the same leve l as t he ja ck
mo unt ing poin t ¢
fig . 307. Do not lift the vehi­
cle at the vertical sill reinforcement.
Rear lifting point
The lift ing po int is located on the ve rt ical rein­
for ceme nt o f the lower s ill fo r th e on bo ar d jac k
¢fig . 30 8.
Lifting with vehicle jack
Refer to ¢ page 372 .
A WARNING
- To reduce the risk of serio us inju ry and vehi ­
cl e d am age.
- Always lift t he ve hicl e only at the s pecial
wo rkshop ho ist and floo r jack lift po ints il­
lustrated¢
fig. 3 0 7 and ¢ fig. 308.
-Fa ilur e to li ft the vehicle at these poin ts
could cause the vehicle to ti lt or fall from
a lift if there is a chang e in vehicle weight
d istr ibut ion a nd balance. This might hap­
pen, for exa mp le, when heavy co mpo­
n e nts su ch as th e e ngi ne block or tra ns­
m is sion are rem ove d.
- W hen removing he avy compon ents like
th ese, an chor vehicle to ho is t or add co rre­
s po nding we igh ts to ma inta in t he cente r of
g ra vity. Otherwise, the vehi cle mi ght t ilt or
s lip off the hoi st, causing ser ious persona l
injury .
{U) Note
- Be aware o f the follo wing po ints b efore lift ­
i n g t he ve hicle:
-The vehicle should never be lifted or
jacked up from underneath the engine oil
pan, the transmission housing, the front
or rear axle or the body side members .
This could lead to serious damage.
- To avoid damage to the underbody or
chassis frame, a rubber pad must be in-
Emergency situations
serted between the floor jack and the lift
points .
- Before driving over a workshop hoist ,
check that the vehicle weight does not
exceed the permissible lifting capacity of
the hoist.
- Before driving over a workshop hoist , en­
sure that there is sufficient clearance be­
tween the hoist and low parts of the ve­
hicle.
385