2018 AUDI A4 fuel cap

Cockpit overv iew
may be higher if there is heavy eng ine load and
high temperatures outside . This is not a cause for
concern as long as
the .¢ page 31 or II
¢ page 31 indicator lights do not turn on.
Boost ind icator
Applies to: vehicles with Audi virtual cockpit
The boost indicator is only displayed in the sport
view
¢ page 15 .
The current eng ine load (meaning the current
boost pressure) is indicated by a bar .
Tachometer
The tachometer displays the engine speed in rev­
olutions per minute
(RPM).
The beginning of the red zone in the tachometer
indicates the maximum perm iss ible engine speed
for all gears once the engine has been broken in
and when it is warmed up to operating tempe ra­
ture. Before reaching this zone, you should sh ift
i n to the next h ighest gear, select the D/S selec­
tor lever position, or remove yo ur foot from the
accelerator pedal.
CD Note
The needle in the tachometer @ ¢ page 10,
fig . 3
o r¢ page 10, fig. 4 may only be in the
red area of the gauge for a short time or there
is a risk of engine damage . The location where
the red zone begins varies depending on the
eng ine.
@ For the sake of the environment
Upshifting early helps you to save fuel and re­
duces operating noise.
Fuel level
The display (J) ¢ page 10, fig. 3 or ¢ page 10,
fig . 4
only functions when the ignition is switch­
ed on . When the display has reached the reserve
mark, a red LED turns on and the
tD in dicator
light tu rns
on ~ page 34. The red LED wi ll blink
when the fuel level is ve ry low.
12
For the tank capacity in your vehicle, refer to the
Technical
Data ¢ page 381.
CD Note
Never drive until the tank is comp letely emp­
ty. The irregu lar supply of fuel that results
from that can cause engine misfires . Uncom­
busted fue l w ill then enter the exhaust sys­
tem. This can cause overheating and damage
to the catalyt ic converter.
Odometer
Fig . 5 In st rum en t cluster : odometer and reset b utto n
Trip odomet er and odometer
The trip odometer shows the distance driven
s ince it was last reset.
It can be used to measure
short distances.
The trip odometer can be reset to zero by press ­
ing
the ~ reset button.
The odometer shows the total distance that the
vehicle has been driven.
Malfunction indicator
If there is a malfunction in the instrument clus­
ter,
DEF will appear in the trip odometer disp lay.
Have the malfu nction corrected as soon as possi­
ble.
(j) Tips
The units of measu rement can be set in the
I nfotainment system
¢ page 248 .

fast acceleration) and have the malfunction cor­rected. See an authorized Audi dealer or
authorized Audi Service Facility .
The electronic speed limiter may be faulty if the
indicator light turns on. For additional informa­
tion, see
¢ page 102, Electronic speed limiter .
The MIL indicator light may also turn on if the
fuel filler cap is not closed correctly
¢page 317.
On-Board Diagnostics
Fig. 22 Location of Data Li nk Con nec tor (DLC )
On-Board Diagnostics monitors the components
of your em ission control system. Each monitored
component in your eng ine system has been as­
signed a code. In case of a ma lfunction, the com­
ponent will be identified and the fault stored as a
code in the control module memory.
The MI L light may also illuminate if there is a
leak in the on -board fuel vapor recovery system.
If the light illuminates after a refueling, stop the
vehicle and make sure the fuel filler cap is prop­ erly closed (only vehicles with gasoline engine)
¢ page 317 .
In order to make an accurate diagnosis, the stor­
ed data can only be displayed using special diag­ nostic equipment (generic scan tool for OBD) .
In order to connect the specia l diagnostic equip­
ment, push the plug into the Data Link Connector
(DLC). The DLC is located to the right of the hood
release¢ fig. 22.
a Your authorized Audi dealer or qualif ied work-al
;:::: shop can interpret the code and perform the nee-
" ~ essary repair . 0 0
~ al
Cockpit overview
A WARNING
--
Do not use the diagnostic connector for per­
sonal use. Incorrect usage can cause malfunc­
tions, which can increase the risk of a colli­
sion!
Indicator lights
Description
The indicator lights in the instrument cluster
blink or turn on. They indicate functions or mal­
functions.
Messages may appear with some indicator lights.
A warn ing s ignal will sound at the same time.
The indicator lights and messages in the instru­
ment cluster display can be covered by other dis­
plays. To show them again, select the second tab
with the mult ifunct ion steer ing
wheel ¢ page 13.
If there are several malfunctions, you can display
them one at a time using the thumbwheel.
Some indicator lights in the display can display in
several co lors.
it Central indicator light
If the. or d indicator light turns on, check
the message in the instr ument cluster.
Overview
Some indicator lights turn on briefly as a function
check when you sw itch the ignition on. These sys ­
tems are marked with
a./ in the fo llowing tab les.
If one of these indicator lights does not turn on,
there is a malfunction in that system.
Your vehicle has either a monochrome display or
a multicolored display, depending on vehicle
equipment. Some indicator lights appear white
on a monochrome display .
The. or Q central
indicator light turns on at the same time to indi-
cate the priority of these indicator lights.
..,.
25

a co .... N ,....
N .... 0 0
3 co
C© ) Brake system
rm Brakes overheating . Please shift to D
rm Brakes overheating. Please select a gear and
follow gear recommendation
There was a heavy load on the brakes. Engage a
suitable gear (manual transm ission) or place the
selector lever in the D/S position (automat ic
transmission) to use the eng ine braking effect
and reduce the load on the brakes.
~·
:t:J /(0 : Brake pads
II (USA models)/£i1 (Canada models) Brake
pads: wear limit reached. You can continue driv­
ing. Please contact Service
The brake pads are worn.
Drive to an authorized Aud i dealer or authorized
Aud i Service Facility as soon as possible to have
the malfunct ion corrected .
c:l:::, Engine control
II Drive system: malfunction! Please contact
Service
There is an engine control malfunction .
Drive slow ly to an author iz ed Audi dealer or au­
thor ized Audi Service Facility to have the eng ine
checked .
W Engine control (diesel engine )
Applies to: vehicles with diesel engines
The engine is preheating if the II indicato r light
turns on when the ignition is switched o n.
I f the indicator light does not turn on or b links
while driving , there is an eng ine control malfunc ­
tion .
Immediately drive slowly to an authori zed Aud i
dealer or authorized Aud i Serv ice Facility to have
the malfunction co rrected .
o Malfunction indicator lamp (MIL)
The malfunction indicato r lamp (MIL) is part of
the On -Board Diagnostic System (OBD II). The Cockpit overview
('4 ,;ymbol turns on when the
ignition is switched
on and turns off again once the engine is started
and running at a steady idle speed. This indicates
that the MIL is function ing correctly.
T he indicator light turns on if there is a malfunc­
tion in the engine electronics. See an authorized
Audi dealer or authorized Audi Service Fac ility to
have the malfunction corrected . For additional
information, see
c:::> page 24.
The indicator light can a lso turn on if the fuel fill­
er cap is not closed correctly
c:::> page 317.
,m,,
Diesel particulate filter
Applies to : vehicles wit h diesel eng ine a nd diesel particulate
filter
II Particulate filter : malfunction! See owner's
manual
T he diese l particulate filter requires regenera­
tion . To support the filter 's self-cleaning func­
tion:
Drive for approximately 15 minutes at a mini ­
mum of 37 mph (60 km/h) in 4th or 5th gear
(manua l transmission) or in the S selector lever
position (automatic transmission). Keep the en­
gine speed at approximately 2,000 RPM . The
temperature increase that will result from th is
can burn off the soot in the filter . The ind icator
light will turn off when the cleaning has complet­
ed successfully .
If the indicator light does not turn off, drive im­
med iate ly to an authori zed Audi dealer or author­
ized Audi Service Facility to have the malfunct ion
corrected .
A WARNING "---
Always adapt your speed to the current
weather, road and traffic conditions. You
should never disobey traffic laws in order to
follow driving recommendations .
@ Tips
For additional informat ion on the diesel par­
ticulate filter, see
c:::> page 322 .
33

any circumstances. Immediately contact the
nearest authorized Audi dealer or author­
ized Audi Service Facility for assistance.
These fuels contain substances that can se­
verely damage the fuel system and the en­
gine if the engine is started.
Refueling
Fuel filler neck
The fuel filler neck is located on the right rear
side panel behind the fuel filler flap.
If the power locking system should fail, you can
still open the flap manually
-for detailed instruc­
tions see
¢page 319.
You can find the fuel tank capacity of your vehicle
in
¢page 381.
The label on the inside of the fuel filler flap tells
you the correct fuel for your vehicle. For more in­
formation about fuel specifications, see
<=?page 315.
Your veh icle fuel tank has an onboard refuelling
vapor recovery system. This feature he lps to pre­
vent fuel vapors from escap ing from the tank and
polluting the environment while you refuel your
vehicle . In order to fill the tank properly while
protecting the environment, please follow this
refueling procedure carefully.
A WARNING
Under normal operating conditions, never car­
ry additional fuel containers in your car. Gas
canisters and other containers used to trans­
port fuel can be dangerous. Such containers,
full or empty, may leak and could cause a fire
in a collision. If you must transport fuel to
use for your lawn mower, snow blower, etc.,
be very careful and always observe local and
state laws regarding the use, transportation
and storage of such fuel containers. Make cer­
tain the container meets industry standards
(ANSI/ASTM F8S2
-86).
(D Note
Never dr ive your vehicle until the fuel tank is
completely empty. The irregu lar supply of
Checking and Filling
fuel can cause misfiring. Gasoline could enter
the exhaust system and damage the catalytic
converter.
Fueling procedure
Fig. 260 Right rear side of the vehicle: opening the fuel
f ilte r door
Fig. 261 Fuel filler door with attached fuel cap
The fuel filler door is unlocked or locked by the
central locking system.
Opening the fuel cap
.,. Press the left side of the fuel filler door to open
it¢
fig. 260 -arrow-.
.,. Unscrew the tank cap counterclockwise.
.,. Place the cap from above on the open fuel filler
door¢
fig. 261.
Closing the fuel cap
.,. Turn the fuel cap to the right until it stops.
.,. Close the fuel filler door until it latches.
Once the pump nozzle switches off, the fuel tank
is "full". Do not fill the tank more. Otherwise the
expansion space in the tank will be filled.
The correct fuel type for your vehicle can be
found on a label located on the inside of the fuel
.,.
317

Checking and Filling
filler door. For additional information on fuel,
see
<=> page 315.
The fuel tank capacity of your vehicle is listed in
the
Technical Data section <=> page 381.
To avoid fuel spilling or evaporating from the fuel
tank always close fuel cap properly and com­
pletely . An improperly closed fuel filler cap may
also cause the MIL lamp
<=>page 24 to come on.
A WARNING
Not paying attention when fueling or han­
dling fuel incorrectly can lead to fires, explo­
sions or serious injuries.
- Fuel ignites easily and can cause serious
burns and other injuries .
- If you do not switch the engine off when fu­
eling and/or do not insert the fuel nozzle
completely into the tank opening, fuel can
leak out or run over. Leaked fuel can ignite
and start a fire .
- Do not use the telephone while fueling. The
electromagnetic rays can cause sparks,
which can ignite fuel vapors and start a fire.
- Do not sit in your vehicle while fueling. If
you must make an exception and enter your
vehicle again while fueling, close the door and touch metal to discharge static electric­
ity before touching the fuel nozzle . Static
electricity can create sparks, which can ig­
nite vapors when fueling.
- Do not smoke or have an open flame in the
area when fueling your vehicle or filling a
fuel container because this increases the
risk of an explosion .
-For your safety , carrying fuel containers in
your vehicle is not recommended. Whether
full or empty, the container can leak and
cause a fire in the event of an accident.
-If you must make an exception and trans­
port a fuel container, note the following:
- Never fill the fuel container with fuel
while it is in or on the vehicle . Stat ic elec ­
tricity is discharged when filling which can
cause the fuel vapors to ignite and in­
creases the risk of an explosion.
- Always place a fuel container on the
ground before filling.
318
-Always hold the fuel nozzle completely in
the fuel container when filling.
-If the fuel container is made of metal, the
fuel nozzle must always be in contact with
the container when filling it with fuel. This
prevents static electricity from discharg­
ing .
-Never spill fuel in the vehicle or the lug­
gage compartment . Evaporated fuel is ex­
plosive and increases the risk of serious in­
jury or death .
- Follow legal requirements when using, storing and transporting fuel containers .
-Make sure the fuel container conforms to
industry standards (ANSI/ASTM F8S2 -86).
{(D Note
- Remove spilled fuel from vehicle paint im­
mediately, because it can damage paint.
- Never drive until the fuel tank is completely
empty. The irregular supply of fuel that re­
sults from that can cause engine misfires.
Uncombusted fuel will enter the exhaust
system and increase the risk of damage to
the catalytic converter.
- If the fuel tank runs completely empty in a
vehicle with a
diesel engine, the ignition
must remain switched on for at least 30
seconds after refueling before starting the
engine.
It may take longer than usual for
the engine to start, even up to a minute.
This is because the air must first bleed out
of the fuel system when starting the engine.
@ For the sake of the environment
Do not overfill the fuel tank, otherwise fuel
can leak out when the vehicle is warming up.
@ Tips
Diesel vehicles are equipped with a diesel mis­
fueling guard.
It allows the vehicle to be fu­
eled only with a diesel fuel pump nozzle. A
worn or damaged nozzle or a nozzle that is
too small may not be able to open the diesel
misfueling guard. If this is the case, try turn­
ing the nozzle before inserting it in the fuel
filler neck, use a different fuel pump, or see
..,_

Checking and Filling
This message appears when there is only enough
Ad Blue left to drive the distance indicated in the
instrument cluster . Fill the Ad Blue .
• Refill with at least x qt (l) Ad Blue. No en­
gine start in x mi (km). See owner's manual
This message appears when there is only enough
Ad Blue left to drive the distance indicated in the
instr ument cluster. Fill the Ad Blue. Otherwise
the engine will not start again if you stop it once
the d istance indicated has been driven .
• Refill with at least x qt (l) AdBlue. Engine
start not possible . See owner's manual
This message appears when the AdBlue tank is
empty. Fill the AdB lue. Otherwise you will not be
able to start the engine again once you stop it .
The AdBlue must be refilled when the amount in
the tank has reached the minim um level
c::> page 320, Preparation.
Incorrect filling/system malfunction
A message appears if the Ad Blue tank was filled
with a fluid other than AdBlue and the system has detected that the tank was fi lled incorrectly ,
or if there is a system malfunction .
II Ad Blue: malfunction! No engine start in
x mi (km). See owner's manual
This message appears when it is only possible to
drive the d istance ind icated in the instrument
cluster. Drive to the nearest authorized Audi
dealer or authorized Aud i Serv ice Facility to have
the malfun ction corrected. Otherwise the engine
will not start again if you stop it once the dis­
tance indicated has been driven .
• Ad Blue: malfunction! No engine start possi­
ble. See owner's manual
This message appears if the system has detected
that the tank was filled incorrectly or that there
is a malfunction . Drive immediately to the near ­
est authorized Aud i dealer or authorized Audi
Service Facility to have the malfunction cor rect­
ed. Otherwise you will not be able to start the en­
g in e again once you stop it .
320
Preparation
App lies to : vehicles with selective cata lyt ic reduct ion
Fig. 264 R ig ht re ar sid e o f th e ve hicle: removing th e Ad B l­
ue cap
The Ad Blue tank open ing is located near the die­
sel tank opening. Add at least the amount of
Ad Blue shown in the instrument cluster display.
This is the minimum amount required to ensure
the system detects the refilling and to start the
engine. You can add a maximum of 6 .3 gallons
(24
L) .
Requ irement: the request to add Ad Blue must
appear in the instrument cluster display .
.. Switch the ignition off.
.. Open the tank fille r doo r c::> page 317 .
.. Turn the tank filler neck cap to the left to re­
move
c::> fig. 264 .
.. Refill Ad Blue using a pump no zzle c::> page 321,
a canister c::> page 321 or a bottle c::>page 321.
A WARNING
AdBlue can irritate the skin, eyes and respira­
tory system .
If there is contact with the fluid,
flush immed iately w ith plenty of water . Con­
sult a physician if necessary .
(D Note
-Only use Ad Blue that conforms to the
standard ISO 22241-1. Do not mix any addi­
ti ves wi th the Ad Blue and do not dilute it
with water .
- Do not add AdBlue to the diesel tank or add
diesel fuel to the Ad Blue tank. Do not start
the engine under any circumstances if the
wrong fuel is filled in the tank. There is a

a co .... N ,....
N .... 0 0
3 co
risk of damaging the fuel tank system and
the engine . See an authorized Audi dealer or
authorized Audi Serv ice Facility for ass is­
tance.
-Ad B lue attacks surfaces such as painted ve­
hicle components, plastic and carpet. Re­
move the fluid as quickly as poss ible with a
damp cloth and plenty of cold wa ter. If the
Ad Blue has already crystallized, use warm
water and a sponge . Ad Blue residue that is
not removed will crystallize and can damage
the affected surface .
-Do not store refill bott les or canisters per­
manent ly in the veh icle. If the container
l ea ks, the escaping AdBl ue could damage
the veh icle inter ior.
-Do not allow AdBlue to come into contact
with clothing. If there is contact with the
fluid , flush immed iate ly w ith plenty of wa­
ter.
@ Tips
F ollow the Ad Blue m anufact urer's instr uc­
tions fo r use and storage .
Refilling AdBlue using a pump
Applies to: vehicles with selective catalytic reduction
.,. Open th e tank fi ller door ¢ page 317, fig . 260.
.,. T u rn the tank filler neck cap to the left to re­
move
c:> page 320 , fig . 264.
.,. Refill AdBlue un til the pump no zzle swit ches
off for the first time ¢ (\1) .
.,. Close the filler neck . ¢ page 322, Completing
AdBlue refill
0 Note
-The pump nozzle handle must be pointing downward when filling . Otherwise the
pump noz zle w ill not sw itch
off automat i­
ca lly
c:> Q) in Preparation on page 320.
-Do not continue filling once the pump noz­
zle automatically switches
off for the first
time . The AdBlue ta nk system could be
overfilled and leak Ad B lue
c:> (D in Prepara­
tion on page 320 .
Check ing and Filling
Refilling AdBlue using a canister
Applies to: vehicles with selective catalytic reduction
+®
Fig. 265 Can is te r w it h attachab le hose
.,. Remove the cover from the refill canis te r¢ .&.
in Preparation on page 3 20, ¢ (Din Prepara ­
tion on page 320 .
.,. Secure the end of the hose(!) on the open ing in
t he canister @by turn ing the hose to the rig ht.
.,. Remove the cap @from the other end of the
hose @ .
.,. Position the end of the hose @ on the filler
neck in the vehicle and turn the hose to the
r ight to tighten it .
.,. Lift the canister up and then tip it. Cont inu e
holding the canis ter in a tipped pos it ion until i t
is empty or until no more flu id flows into the
tank .
.,. Remove the canis ter and close the filler t ube
c:> page 322, Completing AdBlue refill .
(D Note
Only use refill canisters that a re approved fo r
your vehicle. Using ot her systems ca n cause
Ad B lue to leak.
© Tips
- An authorized Aud i dealer o r autho rized
Audi repair facility can tell you wh ich refill
canisters are approved for your vehicle.
- A permitted refill ca niste r contains app roxi­
mately 1.3 gallons (5 l ite rs) of Ad Blue .
Refilling AdBlue using a bottle
Applies to: vehicles with selective catalytic reduction
.,. Remove the cap from the refill bo ttle c:> .&. in
Preparation on page 3 20,
c:> (D in Preparation
on page 320 .
.,.
321

Check ing and F illing
"' Position the bottle on the filler tube and turn
the bottle clockwise unti l it stops turning.
"' Press lightly aga inst the bottom of the bott le
to empty it. Continue pressing the bottom of
the bottle until it is empty or unti l fluid stops
flowing into the tank .
"' Remove the bottle and seal the filler neck
¢ page 322, Completing AdBlue refill .
0 Note
Only use refill bottles that are approved for
your vehicle. Us ing other systems can ca use
Ad Blue to leak.
-You can obta in refill bottles from an author­
i zed Audi dealer or authorized A udi Service
F ac ility.
- A pe rm itted refill bottle conta ins approxi­
mately 0 .5 gallon ( 1.9 liters) of Ad Blue.
Completing AdBlue refill
Applies to: vehicles with selective catalytic reduction
Closing the filler neck
"'Turn the Ad Blue cap to the r ight on the filler
tube unti l th e cap cl ic k s into
p lace ¢.&. in
Prepara tion on page 320,
¢ (Din Preparation
on page 320 ..
"' Then press on the left side of the tank door un-
ti l it latches.
After filling
The vehicle must be driven so tha t the system
recognizes t hat the Ad B lue was refilled. This can
t ake severa l m in utes.
"' If there was no Ad Blue left in the tank and a
r ange of O mi (0 km) was shown in the d isplay,
swi tch the ign ition on fo r abo ut 30 seconds be­
f ore star ting the engine .
(D Tips
Ad Blue in the tank can free ze at very low tem­
pera tures. If this happens, the system will
not detect that the AdB lue was refilled and it
w ill contin ue to inform you of the low AdBlue
322
leve l. The message tu rns off as soon as the
tank thaws out again .
Emissions control
systems
Cat alytic converter
Applies to: vehicles with gasoline engines
T he vehicle may only be driven w ith un leaded
gaso line, otherwise the catalytic converter will be
destroyed .
Never drive unti l the tan k is comp lete ly empty .
T he irregu lar supply of fuel that resu lts from that
can cause eng ine misfires. Uncombusted fuel will
enter the exhaust system , which can cause over­
heating and damage to the catalytic converte r.
Di esel particulate filt er
Applies to: vehicles with diesel engines
The diese l particulate filter filters nearly all of
the soot part icles out of the exhaust. The filter
cleans itself automat ica lly under norma l dr iv ing
cond it io ns. If the filter cannot clean itself (for ex­
amp le, because yo u are on ly driving short distan ­
ces), the filter becomes clogged with soot and
the
1111 i ndicato r light for the diese l particulate
filte r tu rns
on ¢ page 33.
_&. WARNING
The tempera ture o f the e xhaust sys tem is
h igh, both when driving and a fter stopping
the engine.
-
-Never tou ch the e xhaus t tail p ipes o nce they
have become hot. This cou ld resu lt in burns.
-D o not p ark your vehicle over flamm able
materials such as grass or leaves because
the hig h temperature of the emissions con­
trol system (catalyt ic converter or d iese l
pa rticu late filter) co uld start a fire.
- Do not apply underbody protectant in the
exhaust system area, beca use this increases
the risk of f ire.