Periodic maintenance an d a djustment
6-39
6
TIPThe drive chain does not need to be
disassembled in order to remove and
install the wheel.9. Remove the wheel.
To install the rear wheel 1. Install the drive chain onto the rear sprocket.
2. Install the wheel by installing the collars on both sides and installing
the washer and the wheel axle
from the right side.
3. Install the washer and the axle nut.
4. Connect the brake rod to the brake camshaft lever, and then in-
stall the brake pedal free play ad-
justing nut onto the brake rod.
5. Connect the brake torque rod to the brake shoe plate by installing
the bolt and the nut.
6. Adjust the drive chain slack. (See page 6-24.)
7. Take the motorcycle off the cen- terstand so that the rear wheel is
on the ground, and then put the
sidestand down. 8. Adjust the brake pedal free play.
(See page 6-21.)
WARNING
EWA10661
After a djustin g the brake pe dal free
play, check the operation of the
b rake li ght.
EAU25853
Trou bleshootin gAlthough Yamaha motorcycles receive
a thorough inspection before shipment
from the factory, trouble may occur
during operation. Any problem in the
fuel, compression, or ignition systems,
for example, can cause poor starting
and loss of power.
The following troubleshooting chart
represents a quick and easy procedure
for checking these vital systems your-
self. However, should your motorcycle
require any repair, take it to a Yamaha
dealer, whose skilled technicians have
the necessary tools, experience, and
know-how to service the motorcycle
properly.
Use only genuine Yamaha replace-
ment parts. Imitation parts may look
like Yamaha parts, but they are often
inferior, have a shorter service life and
can lead to expensive repair bills.
WARNING
EWA15142
When checkin g the fuel system, do
not smoke, an d make sure there are
no open flames or sparks in the ar-
ea, inclu din g pilot li ghts from water
UBT4E0E0.book Page 39 Thursday, November 17, 2016 10:55 AM
Specifications
8-1
8
Dimensions:Overall length:2005 mm (78.9 in)
Overall width:
735 mm (28.9 in)
Overall height: 1050 mm (41.3 in)
Seat height: 795 mm (31.3 in)
Wheelbase:
1320 mm (52.0 in)
Ground clearance: 150 mm (5.91 in)
Minimum turning radius: 2.2 m (7.22 ft)Wei ght:Curb weight:
129 kg (284 lb)Engine:Combustion cycle:
4-stroke
Cooling system: Air cooled
Valve train: SOHC
Number of cylinders:
Single cylinder
Displacement: 125 cm³
Bore × stroke:
52.4 × 57.9 mm (2.06 × 2.28 in)
Compression ratio:
10.0 : 1 Starting system:
Electric starter
Lubrication system: Wet sump
Engine oil:Recommended brand:
YAMALUBE
SAE viscosity grades: 10W-40, 20W-40
Recommended engine oil grade: API service SG type or higher, JASO
standard MA
Engine oil quantity:
Oil change:1.00 L (1.06 US qt, 0.88 Imp.qt)
With oil filter removal:
1.10 L (1.16 US qt, 0.97 Imp.qt)Air filter:Air filter element:Dry element
Fuel:Recommended fuel:Regular unleaded gasoline (Gasohol [E10]
acceptable)
Fuel tank capacity: 14 L (3.7 US gal, 3.1 Imp.gal)
Fuel reserve amount:
2.2 L (0.58 US gal, 0.48 Imp.gal)Fuel injection:Throttle body:ID mark:BT41 00Spark plu g(s):Manufacturer/model:
NGK/CPR8EA-9
Spark plug gap: 0.8–0.9 mm (0.031–0.035 in)Clutch:Clutch type:
Wet, multiple-discDrivetrain:Primary reduction ratio:3.409 (75/22)
Final drive:
Chain
Secondary reduction ratio: 3.071 (43/14)
Transmission type: Constant mesh 5-speed
Gear ratio:
1st:2.714 (38/14)
2nd:
1.789 (34/19)
010305070 90110
130 ˚F
-20 -10 0 10 20 3040
50 ˚C
SAE 10W-40
SAE 20W-40
UBT4E0E0.book Page 1 Thursday, November 17, 2016 10:55 AM