2017 YAMAHA YS125 drain bolt

Description
2-2
2
EAU10421
Right view
3,4
1
2
5
6
7
8
9
1. Shock absorber assembly spring preload adjusting ring (page 3-11)
2. Owner’s tool kit (page 6-2)
3. Battery (page 6-30)
4. Fuses (page 6-31)
5. Engine oil filter element (page 6-11)
6. Engine oil drain bolt (page 6-11)
7. Engine oil filler cap (page 6-11)
8. Brake pedal (page 3-7) 9. Rear brake light switch (page 6-21)UBT4E0E0.book Page 2 Thursday, November 17, 2016 10:55 AM

Periodic maintenance an d a djustment
6-12
6
ficiently
before removin g the oil
filler cap.
[EWA17640]
NOTICE: Do not
operate the vehicle until you
know that the en gine oil level is
sufficient.
[ECA10012]
TIPThe engine oil should be between the
minimum and maximum level marks.4. If the engine oil is below the mini- mum level mark, add sufficient oil
of the recommended type to raise
it to the correct level.
5. Check the O-ring for damage, and replace it if necessary.
6. Install and tighten the engine oil filler cap.
To chan ge the en gine oil (with or
without oil filter element replace-
ment) 1. Start the engine, warm it up for several minutes, and then turn it
off.
2. Place an oil pan under the engine to collect the used oil.
3. Remove the engine oil filler cap, the engine oil drain bolt and its
gasket to drain the oil from the
crankcase.
TIPSkip steps 4–6 if the oil filter element is
not being replaced.4. Remove the oil filter element coverby removing the bolts.
1. Engine oil filler cap
1. O-ring
2. Engine oil dipstick
3. Maximum level mark
4. Minimum level mark
1
4 321
1. Engine oil drain bolt
2. Gasket
1. Bolt
2. Oil filter element cover
12
1
2
UBT4E0E0.book Page 12 Thursday, November 17, 2016 10:55 AM

Periodic maintenance an d a djustment
6-13
6 5. Remove and replace the oil filter
element and O-ring.
6. Install the oil filter element cover by installing the bolts, then tight-
ening them to the specified
torque.
TIPMake sure that the O-ring is properly
seated.7. Install the engine oil drain bolt andits new gasket, and then tighten
the bolt to the specified torque. 8. Refill with the specified amount of
the recommended engine oil.
NOTICE
ECA11621
In or der to prevent clutch slip-
pa ge (since the en gine oil also
lu bricates the clutch), do not
mix any chemical additives. Do
not use oils with a diesel speci-
fication of “CD” or oils of a hi gh-
er quality than specifie d. In
a ddition, do not use oils la beled
“ENERGY CONSERVING II” or
hi gher.
 Make sure that no forei gn mate-
rial enters the crankcase.
9. Check the O-ring for damage, and replace it if necessary.
10. Install and tighten the engine oil filler cap.NOTICE
ECA10441
After chan gin g the en gine oil, b e
sure to check the oil pressure as de-
scri bed b elow.To check the oil pressure
1. Remove cowling A. (See page 6-8.)
2. Remove the Y.R.C.S. (Yamaha Ram-Air Cooling System) cap.
(See page 6-10.)
1. Oil filter element
2. O-ringTightenin g torque:
Oil filter element cover bolt: 10 N·m (1.0 kgf·m, 7.2 lb·ft)
2 1
Ti
ghtenin g torque:
Engine oil drain bolt:
20 N·m (2.0 kgf·m, 14 lb·ft)
Recommen ded en gine oil:
See page 8-1.
Oil quantity:
Oil change:1.00 L (1.06 US qt, 0.88 Imp.qt)
With oil filter removal:
1.10 L (1.16 US qt, 0.97 Imp.qt)
1. Engine oil filler cap
2. O-ring
21
UBT4E0E0.book Page 13 Thursday, November 17, 2016 10:55 AM