2017 YAMAHA WOLVERINE engine coolant

8-25
8
3. If the coolant is at or below the minimumlevel mark, remove the coolant reservoir
cap, add coolant to the maximum level
mark, and install the reservoir cap. Changing the coolant
WARNING
EWB01891Wait for the engine and radiator to cool be-
fore removing the radiator cap. You could
be burned by hot fluid and steam blown
out under pressure. Always place a thick
rag over the cap when opening. Allow any
remaining pressure to escape before com-
pletely removing the cap. 1. Park the vehicle on a level surface.
2. Remove the hood. (See page 8-10 for
hood removal and installation proce-
dures.)
3. Place a container under the engine to col- lect the used coolant.
4. Remove the radiator cap.
1. Coolant reservoir cap
2. Maximum level mark
3. Minimum level markCoolant reservoir capacity (up to the maxi-
mum level mark): 0.28 L (0.30 US qt, 0.25 Imp.qt)
123
U2MB7BE0.book Page 25 Thursday, March 3, 2016 11:46 AM

8-27
8
8. Disconnect the coolant reservoir hose,and then drain the coolant from the cool-
ant reservoir.
9. After draining the coolant, thoroughly flush the cooling system with clean tap
water.
10. Install the coolant drain bolt and its new gasket and then tighten the bolt to the
specified torque. 11. Connect the coolant reservoir hose.
12. Pour the recommended coolant into the
radiator until it is full.
13. Pour the recommended coolant into the
reservoir to the maximum level mark, and
then install the reservoir cap.
NOTICEECB02190Mix antifreeze with distilled water only.
However, if distilled water is not available,
soft water may be used for refilling. Do not
use hard water or salt water since they are
harmful to the engine.
1. Coolant reservoir cap
2. Coolant reservoir hose
12
Tightening torque:Coolant drain bolt:8 N·m (0.8 kgf·m, 5.8 lb·ft)
U2MB7BE0.book Page 27 Thursday, March 3, 2016 11:46 AM

8-28
8
14. Remove the right panel and right rearpanel. (See page 8-11 for right panel and
right rear panel removal and installation
procedures.)
15. Loosen the water pump air bleed bolt, without removing it, to allow all of the air
to escape from the air bleed bolt hole. 16. When coolant begins to flow out of the
bolt hole, tighten the water pump air
bleed bolt to the specified torque.
17. Loosen the cylinder head air bleed bolt, without removing it, to allow all of the air
to escape from the air bleed bolt hole.Antifreeze/water mixture ratio:1:1
Recommended antifreeze: High-quality ethylene glycol antifreeze con-
taining corrosion inhibitors for aluminum
engines
Coolant quantity: Radiator (including all routes):2.85 L (3.01 US qt, 2.51 Imp.qt)
Coolant reservoir (up to the maximum level
mark): 0.28 L (0.30 US qt, 0.25 Imp.qt)
1. Water pump air bleed boltTightening torque:Water pump air bleed bolt:8 N·m (0.8 kgf·m, 5.8 lb·ft)
1
U2MB7BE0.book Page 28 Thursday, March 3, 2016 11:46 AM

8-29
8
18. When coolant begins to flow out of thebolt hole, tighten the cylinder head air
bleed bolt to the specified torque.
19. Start the engine and let it idle for ten mi- nutes.
20. Rev the engine five times.
21. Pour additional coolant into the radiator until it is full. 22. Stop the engine and allow it to cool. If the
coolant level has dropped after the en-
gine has cooled, add sufficient coolant
until it reaches the top of the radiator, and
then install the radiator cap.
23. Check the coolant level in the reservoir. If necessary, remove the coolant reservoir
cap, add coolant to the maximum level
mark, and then install the cap.
24. Start the engine, and then check for cool- ant leakage.
TIPIf any leakage is found, have a Yamaha dealer
check the cooling system. 25. Install the panels and the hood.EBU32400Axle bootsCheck the axle boots for holes or tears.
If any damage is found, have them replaced
by a Yamaha dealer.
1. Cylinder head air bleed boltTightening torque:Cylinder head air bleed bolt:10 N·m (1.0 kgf·m, 7.2 lb·ft)
1
U2MB7BE0.book Page 29 Thursday, March 3, 2016 11:46 AM

8-60
8
Engine overheating
Wait for the engine to cool before removing the radiator cap. WARNING! If the engine is not
cool when removing the radiator cap, hot fluid and steam could blow out under pressure
and burn you.
[EWB03460]
Place a thick rag over the cap and remove the cap slowly to allow any re-
maining pressure to escape.
TIPIf it is difficult to get the recommended coolant, tap water can be used temporarily, provided that
it is changed to the recommende d coolant as soon as possible. Wait until the
engine has cooled.
Check the coolant level in the
coolant reservoir and/or radiator.
Level is OK.Level is low, check the
cooling system for leakage.
No
leakage.Leakage.
Ask a Yamaha dealer to inspect
and repair the cooling system.Add coolant. (See TIP.)
Restart the engine. If the engine overheats again, ask a
Yamaha dealer to inspect and/or repair the cooling system.
U2MB7BE0.book Page 60 Thursday, March 3, 2016 11:46 AM

10-2
10
Type:SAE 0W-30, 10W-30, 10W-40, 15W-40, 20W-40 or 20W-
50
Recommended engine oil grade: API service SG type or higher, JASO standard MA
Engine oil quantity: Without oil filter cartridge replacement:2.20 L (2.33 US qt, 1.94 Imp.qt)
With oil filter cartridge replacement: 2.30 L (2.43 US qt, 2.02 Imp.qt)Final gear oil:Type:SAE 80 API GL-4 Hypoid gear oil
Quantity: 0.64 L (0.68 US qt, 0.56 Imp.qt)Differential gear oil:Type:SAE 80 API GL-4 Hypoid gear oil Quantity:
0.18 L (0.19 US qt, 0.16 Imp.qt)
Coolant quantity:Coolant reservoir (up to the maximum level mark):
0.28 L (0.30 US qt, 0.25 Imp.qt)
Radiator (including all routes): 2.85 L (3.01 US qt, 2.51 Imp.qt)Air filter:Air filter element:
Wet elementFuel:Recommended fuel:Regular unleaded gasoline only
Fuel tank capacity:
36.7 L (9.69 US gal, 8.07 Imp.gal)Fuel injection:Throttle body:ID mark:2MB1 00Spark plug (s):Manufacturer/model:
NGK/CPR7EA-9
Spark plug gap: 0.8–0.9 mm (0.031–0.035 in)Clutch:Clutch type:
Wet, centrifugal automaticTransmission:Secondary reduction system:Shaft drive
0 10 30 50 70 90 110 130 F
–20 –10 0 10 20 30 40 50 CSAE 0W-30
SAE 10W-30
SAE 10W-40
SAE 15W-40
SAE 20W-40SAE 20W-50
U2MB7BE0.book Page 2 Thursday, March 3, 2016 11:46 AM

10-4
10
Rear wheel:Wheel type:Cast wheel (YXE70WPAH)
Panel wheel (YXE70WPHH, YXE70WPXH)
Rim size: 12 x 7.5ATFront brake:Type:Hydraulic disc brake
Operation: Unified brake
Specified brake fluid:
DOT 4Rear brake:Type:Hydraulic disc brake
Operation:
Unified brake
Specified brake fluid: DOT 4Front suspension:Type:
Double wishbone
Spring/shock absorber type: Coil spring/gas-oil damper
Wheel travel: 246 mm (9.7 in)Rear suspension:Type:Double wishbone Spring/shock absorber type:
Coil spring/gas-oil damper
Wheel travel: 269 mm (10.6 in)
Electrical system:Ignition system:TCI
Charging system: AC magnetoBattery:Model:U1-H11L
Voltage, capacity: 12 V, 28.0 AhHeadlight(s):Bulb type:Halogen bulbBulb voltage, wattage × quantity:Headlight:
12 V, 35.0/35.0 W × 2
Tail/brake light: 12 V, 5.0/21.0 W × 2
Neutral indicator light: LED
Reverse indicator light:
LED
Coolant temperature warning light: LED
Engine trouble warning light: LED
U2MB7BE0.book Page 4 Thursday, March 3, 2016 11:46 AM

12-1
12
INDEX
AAccelerator pedal ......................................................... 4-13
Accelerator pedal, Pre-operation check ........................ 5-6
Air filter case/air duct check hose, cleaning ................ 8-36
Air filter element, cleaning ........................................... 8-32
Auxiliary DC jack .......................................................... 4-33
Axle boots .................................................................... 8-29BBasic guide for safe use ................................................ 7-1
Battery, Periodic maintenance .................................... 8-47
Brake fluid level, checking ........................................... 8-39
Brake fluid, replacing ................................................... 8-41
Brake light switch, adjusting ........................................ 8-42
Brake pedal .................................................................. 4-13
Brake pedal and accelerator pedal, lubrication ........... 8-43
Brake pedal, checking ................................................. 8-41
Brakes, Periodic maintenance ..................................... 8-38
Brakes, Pre-operation check ......................................... 5-3CCable, inspecting and lubrication ................................ 8-42
Cargo bed .................................................................... 4-21
Cleaning ......................................................................... 9-1
Control cables, Pre-operation check ............................. 5-8
Coolant, Periodic maintenance ................................... 8-24
Coolant, Pre-operation check ........................................ 5-6
Coolant temperature warning light ................................ 4-4
Cup holders ................................................................. 4-20DDifferential gear oil, Periodic maintenance .................. 8-22 Differential gear, Pre-operation check ........................... 5-6
Doors ........................................................................... 4-15
Driver seat position ...................................................... 4-16
Drive select lever ......................................................... 4-14
Drive select lever operation and reverse driving ............ 6-3
EEngine break-in .............................................................. 6-1
Engine oil and oil filter cartridge, Periodic
maintenance .............................................................. 8-14
Engine oil, Pre-operation check .................................... 5-5
Engine trouble warning light .......................................... 4-4
EPS warning light .......................................................... 4-5FFinal gear oil, Periodic maintenance ............................ 8-20
Final gear, Pre-operation check .................................... 5-6
Fittings and fasteners, Pre-operation check ................. 5-7
Front and rear brake pads, checking .......................... 8-39
Fuel, Pre-operation check ............................................. 5-3
Fuel tank cap ............................................................... 4-15
Fuse, replacing ............................................................ 8-52GGlove compartment ..................................................... 4-18HHeadlight beam, adjusting ........................................... 8-57
Headlight bulb, replacing ............................................. 8-54
Helmet indicator light ..................................................... 4-5
High-range indicator light .............................................. 4-2
Hood ............................................................................ 8-10
Horn switch .................................................................. 4-12IIdentification number records ...................................... 11-1
U2MB7BE0.book Page 1 Thursday, March 3, 2016 11:46 AM