2017 YAMAHA TRICITY oil type

Periodic maintenance and adjustment
6-10
6 4. If the engine oil is not between the
tip of the dipstick and the maxi-
mum level mark, add sufficient oil
of the recommended type to raise
it to the correct level.
5. Check the O-ring for damage, and
replace it if necessary.
6. Insert the dipstick into the oil filler
hole, and then tighten the oil filler
cap.
To change the engine oil and clean
the oil strainer
1. Start the engine, warm it up for
several minutes, and then turn it
off.
2. Place an oil pan under the engine
to collect the used oil.
3. Remove the engine oil filler cap
and engine oil drain bolts A and B
to drain the oil from the crankcase.
NOTICE: When removing the
engine oil drain bolt B, the O-
ring, compression spring, and
oil strainer will fall out. Take
care not to lose these parts.
[ECAT1022]
4. Clean the engine oil strainer with
solvent, and then check it for dam-
age and replace it if necessary.
5. Install the engine oil strainer, com-
pression spring, new O-ring and
engine oil drain bolt B.
TIP
Make sure that the O-ring is properly
seated.
6. Install engine oil drain bolt A and
its new gasket, and then tighten
both drain bolts to their specified
torques.
7. Refill with the specified amount of
the recommended engine oil.
1. Engine oil filler cap
2. O-ring
3. Engine oil dipstick
4. Maximum level mark
5. Tip of the engine oil dipstick
1
3
2
4
5
1. Engine oil drain bolt A
2. Gasket
3. Oil strainer
4. Compression spring
5. O-ring
6. Engine oil drain bolt B
Tightening torque:
Engine oil drain bolt A:
20 N·m (2.0 kgf·m, 14 lb·ft)
Engine oil drain bolt B:
32 N·m (3.2 kgf·m, 23 lb·ft)
Recommended engine oil:
See page 8-1.
Oil quantity:
0.90 L (0.95 US qt, 0.79 Imp.qt)
1
3
4
5
6
2
UBR7E0E0.book Page 10 Tuesday, October 25, 2016 2:44 PM

Periodic maintenance and adjustment
6-16
6 damaging the air filter element,
handle it gently and carefully,
and do not twist it.
[ECA10522]
4. Apply oil of the recommended
type to the entire surface of the
sponge material, and then
squeeze the excess oil out.
TIP
zThe air filter element should be
wet but not dripping.
zCheck the air filter element for ex-
cessive dirt or damage and re-
place it if necessary.
5. Insert the element into the V-belt
case.
6. Install the air filter element cover
by installing the screws.
EAU21386
Checking the throttle grip free
play
Measure the throttle grip free play as
shown.
Periodically check the throttle grip free
play and, if necessary, have a Yamaha
dealer adjust it.
1. V-belt case air filter element
Recommended oil:
Yamaha foam air filter oil or other
quality foam air filter oil
1
1. Throttle grip free play
Throttle grip free play:
3.0–7.0 mm (0.12–0.28 in)
1
UBR7E0E0.book Page 16 Tuesday, October 25, 2016 2:44 PM

Periodic maintenance and adjustment
6-22
6
EAU40262
Checking the brake fluid level
Before riding, check that the brake fluid
is above the minimum level mark.
Check the brake fluid level with the top
of the reservoir level. Replenish the
brake fluid if necessary.
Front brake
Rear brake
WARNING
EWA16011
Improper maintenance can result in
loss of braking ability. Observe
these precautions:
zInsufficient brake fluid may al-
low air to enter the brake sys-
tem, reducing braking
performance.zClean the filler cap before re-
moving. Use only DOT 4 brake
fluid from a sealed container.
zUse only the specified brake flu-
id; otherwise, the rubber seals
may deteriorate, causing leak-
age.
zRefill with the same type of
brake fluid. Adding a brake fluid
other than DOT 4 may result in a
harmful chemical reaction.
zBe careful that water or dust
does not enter the brake fluid
reservoir when refilling. Water
will significantly lower the boil-
ing point of the fluid and may re-
sult in vapor lock, an
d dirt may
clog the ABS hydraulic unit
valves.
NOTICE
ECA17641
Brake fluid may damage painted
surfaces or plastic parts. Always
clean up spilled fluid immediately.
As the brake pads wear, it is normal for
the brake fluid level to gradually go
down. A low brake fluid level may indi-
cate worn brake pads and/or brake
system leakage; therefore, be sure to
check the brake pads for wear and the
brake system for leakage. If the brake
fluid level goes down suddenly, have a
Yamaha dealer check the cause before
further riding.
1. Minimum level mark
1. Minimum level mark
Specified brake fluid:
DOT 4
1
1
UBR7E0E0.book Page 22 Tuesday, October 25, 2016 2:44 PM

Specifications
8-1
8
Dimensions:
Overall length:
1980 mm (78.0 in)
Overall width:
750 mm (29.5 in)
Overall height:
1210 mm (47.6 in)
Seat height:
780 mm (30.7 in)
Wheelbase:
1350 mm (53.1 in)
Ground clearance:
125 mm (4.92 in)
Minimum turning radius:
2.5 m (8.20 ft)
Weight:
Curb weight:
159 kg (351 lb) (MWS125-C)
164 kg (362 lb) (MWS125-A)
Engine:
Combustion cycle:
4-stroke
Cooling system:
Liquid cooled
Valve train:
SOHC
Number of cylinders:
Single cylinder
Displacement:
125 cm³
Bore × stroke:
52.0 × 58.7 mm (2.05 × 2.31 in)
Compression ratio:
11.2 : 1
Starting system:
Electric starter
Lubrication system:
Wet sump
Engine oil:
Recommended brand:
YAMALUBE
SAE viscosity grades:
10W-40
Recommended engine oil grade:
API service SG type or higher, JASO
standard MA or MB
Engine oil quantity:
Oil change:
0.90 L (0.95 US qt, 0.79 Imp.qt)
Final transmission oil:
Type:
Motor oil SAE 10W-30 type SE or higher or
Gear oil SAE 85W GL-3
Quantity:
0.15 L (0.16 US qt, 0.13 Imp.qt)
Coolant quantity:
Coolant reservoir (up to the maximum level
mark):
0.25 L (0.26 US qt, 0.22 Imp.qt)
Radiator (including all routes):
0.46 L (0.49 US qt, 0.40 Imp.qt)
Air filter:
Air filter element:
Oil-coated paper element
Fuel:
Recommended fuel:
Regular unleaded gasoline (Gasohol [E10]
acceptable)
Fuel tank capacity:
7.2 L (1.9 US gal, 1.6 Imp.gal)
Fuel injection:
Throttle body:
ID mark:
BR71 00
Spark plug(s):
Manufacturer/model:
NGK/CPR8EA-9
Spark plug gap:
0.8–0.9 mm (0.031–0.035 in)
Clutch:
Clutch type:
Dry, centrifugal, shoe
Drivetrain:
Primary reduction ratio:
1.000
Final drive:
Gear
Secondary reduction ratio:
10.208 (56/16 x 35/12)
Transmission type:
V-belt automatic
Chassis:
Frame type:
Underbone
Caster angle:
20.0 °
Trail:
67 mm (2.6 in)
UBR7E0E0.book Page 1 Tuesday, October 25, 2016 2:44 PM

Specifications
8-2
8
Track:
385 mm (15.2 in)
Front tire:
Type:
Tubeless
Size:
90/80-14M/C 43P
Manufacturer/model:
IRC/SCT-003
Rear tire:
Type:
Tubeless
Size:
130/70-13M/C 63P
Manufacturer/model:
IRC/SCT-003
Loading:
Maximum load:
167 kg (368 lb)
(Total weight of rider, passenger, cargo
and accessories)
Tire air pressure (measured on cold
tires):
1 person:
Front:
200 kPa (2.00 kgf/cm², 29 psi)
Rear:
225 kPa (2.25 kgf/cm², 33 psi)
2 persons:
Front:
200 kPa (2.00 kgf/cm², 29 psi)
Rear:
225 kPa (2.25 kgf/cm², 33 psi)
Front wheel:
Wheel type:
Cast wheel
Rim size:
14M/C x MT2.15
Rear wheel:
Wheel type:
Cast wheel
Rim size:
13M/C x MT3.50
Unified brake system:
Operation:
Activated by rear brake
Front brake:
Type:
Hydraulic disc brakeSpecified brake fluid:
DOT 4
Rear brake:
Type:
Hydraulic disc brake
Specified brake fluid:
DOT 4
Front suspension:
Type:
Telescopic fork
Spring:
Coil spring
Shock absorber:
Hydraulic damper
Wheel travel:
90 mm (3.5 in)
Rear suspension:
Type:
Unit swing
Spring:
Coil spring
Shock absorber:
Hydraulic damper
Wheel travel:
90 mm (3.5 in)
Electrical system:
System voltage:
12 V
Ignition system:
TCI
Charging system:
AC magneto
Battery:
Model:
YTZ7V
Voltage, capacity:
12 V, 6.0 Ah (10 HR)
Bulb wattage:
Headlight:
LED
Brake/tail light:
LED
Front turn signal light:
10.0 W
Rear turn signal light:
10.0 W
Auxiliary light:
LED
License plate light:
5.0 W
UBR7E0E0.book Page 2 Tuesday, October 25, 2016 2:44 PM