2017 YAMAHA TRICITY display

Instrument and control functions
3-5
3
EAU74444
Multi-function meter unit
WARNING
EWA12423
Be sure to stop the vehicle before
making any setting changes to the
multi-function meter unit. Changing
settings while riding can distract the
operator and increase the risk of an
accident.
The multi-function meter unit is
equipped with the following:
za speedometer
za fuel meter
za clock
zan outside air temperature display
za multi-function display
zan oil change indicator
za V-belt replacement indicator
TIP


tons.
Speedometer
The speedometer shows the vehicle’s
traveling speed.
Fuel meter
The fuel meter indicates the amount of
fuel in the fuel tank. The display seg-
ments of the fuel meter disappear from
“F” (full) towards “E” (empty) as the fuel
level decreases. When the last seg-
ment of the fuel meter and the fuel level
warning indicator “ ” start flashing,
refuel as soon as possible. When the
key is first turned to “ON”, all the dis-
1. Clock
2. “SELECT” button
3. Fuel level warning indicator “ ”
4. Fuel meter
5. Speedometer
6. “RESET” button
7. Outside air temperature display
8. Multi-function display
9. Oil change indicator “OIL CHANGE”
10.V-belt replacement indicator “V-BELT”
12345 6
9 107
8
1. Speedometer
1. Fuel level warning indicator Ž
2. Fuel meter
1
1
2
UBR7E0E0.book Page 5 Tuesday, October 25, 2016 2:44 PM

Instrument and control functions
3-6
3play segments of the fuel meter will
come on for a few seconds, and then
the fuel meter will show the actual fuel
level.
TIP
If a problem is detected in the fuel me-
ter electrical circuit, all the display seg-
ments and the fuel level warning
indicator start flashing. Have a Yamaha
dealer check the vehicle.
Clock “CLOCK”
The clock uses a 12-hour time system.
To set the clock:
1. Push both the “SELECT” button
and the “RESET” button for two
seconds. The hour digits will start
flashing.
2. Use the “RESET” button to set the
hours.
3. Push the “SELECT” button, and
the minute digits will start flashing.
4. Use the “RESET” button to set the
minute digits.
5. Push the “SELECT” button to start
the clock.Outside air temperature display
“OUT TEMP”
This display shows the outside air tem-
perature from –10 °C to 40 °C in 1 °C
increments. The temperature dis-
played may vary from the actual out-
side air temperature.
TIP
zIf the outside air temperature falls
below –10 °C, a lower temperature
than –10 °C will not be displayed.
zIf the outside air temperature
climbs above 40 °C, a higher tem-
perature than 40 °C will not be dis-
played.
zThe accuracy of the temperature
reading may be affected when rid-
ing slowly (approximately under
20 km/h [12 mi/h]) or when
stopped at traffic signals, railroad
crossings, etc.
1. Clock
1
1. Outside air temperature display
1
UBR7E0E0.book Page 6 Tuesday, October 25, 2016 2:44 PM

Instrument and control functions
3-7
3 Multi-function display
Under normal conditions, the multi-
function display can be set to display
the following.
zodometer “ODO”
ztripmeters “TRIP 1” or “TRIP 2”
zoil change tripmeter “OIL TRIP”
zV-belt replacement tripmeter
“BELT TRIP”
Push the “SELECT” button to switch
the display between the odometer ,
tripmeters 1 and 2, the oil change trip-
meter and the V-belt replacement trip-
meter in the following order:
ODO → TRIP 1 → TRIP 2 → OIL TRIP
→ BELT TRIP → ODO
To reset tripmeter 1 or 2, select it by
pushing the “SELECT” button, and
then push the “RESET” button for one
second.
TIP
zThe odometer will lock at 999999.
zTripmeters 1 and 2 will reset and
continue counting after 9999.9 is
reached.
Fuel reserve tripmeter
When approximately 1.6 L (0.42 US
gal, 0.35 Imp.gal) of fuel remains in the
fuel tank, the last segment of the fuel
meter and the fuel level warning indica-
tor will start flashing. The display will
automatically change to the fuel re-
serve tripmeter and start counting the
distance traveled from that point. In
this case, push the “SELECT” button
to switch the display in the following
order:
F → TRIP 1 → TRIP 2 → OIL TRIP →
BELT TRIP → ODO → F
To temporarily turn off the fuel reserve
tripmeter, select it by pushing the “SE-
LECT” button, and then push the “RE-
SET” button for one second. To turn
the fuel reserve tripmeter back on, turn
the key to “OFF” and then to “ON”. The
fuel reserve tripmeter will be displayed
again after one minute.
The fuel reserve tripmeter will reset au-
tomatically and disappear after refuel-
ing and traveling 5 km (3 mi).
1. Multi-function display
1
1. Fuel reserve tripmeter
1
UBR7E0E0.book Page 7 Tuesday, October 25, 2016 2:44 PM