2017 YAMAHA MT-09 turn signal bulb

Table of contents
Lubricating the swingarm pivots......................................... 7-31
Checking the front fork ................. 7-31
Checking the steering . .................. 7-32
Checking the wheel bearings ....... 7-32
Battery .......................................... 7-32
Replacing the fuses ...................... 7-34
Vehicle lights ................................ 7-36
Replacing a turn signal light bulb ........................................... 7-37
Supporting the motor cycle............ 7-37
Troubleshooting............................ 7-38
Troubleshooting charts ................. 7-39
Motorcycle care and storage .......... 8-1
Matte color caution ......................... 8-1
Care................................................ 8-1
Storage ........................................... 8-3
Specifications .................................. 9-1
Consumer information .................. 10-1
Identification numbers .................. 10-1
Diagnostic connector ... ................. 10-2
Vehicle data recordin g.................. 10-2
Index ............................................... 11-1
BS2-9-E0.book 2 ページ ２０１６年９月８日　木曜日　午前１１時０分

Periodic maintenance and adjustment
7-36
1
2
3
4
5
67
8
9
10
11
12 check if the device operates.
4. If the fuse immediately blows again, have a Yamaha dealer
check the electrical system.
EAU76271
Vehicle lightsExcept for the turn signal lights, this
model is equipped with full-LED light-
ing. If a light does not come on, check
the fuses and then have a Yamaha
dealer check the vehicle.
If a turn signal light does not come,
check and replace the bulb. (See
page 7-37.)TIPWhen the dimmer switch is set to high
beam or the passing switch is pushed,all four headlights come on.
NOTICE
ECA16581
Do not affix any type of tinted film orstickers to the headlight lens.
1. Headlight (low beam)
2. Headlight (high beam)
3. Auxiliary light
12
3
BS2-9-E0.book 36 ページ ２０１６年９月８日　木曜日　午前１１時０分

Periodic maintenance and adjustment7-37
1
2
3
4
5
678
9
10
11
12
EAU24205
Replacing a turn signal light
bulb1. Remove the turn signal light lens by removing the screw.
2. Remove the burnt-out bulb by pushing it in and turning it counter-
clockwise. 3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
4. Install the lens by installing the screw. NOTICE: Do not over-
tighten the screw, otherwise the
lens may break.
[ECA11192] EAU67131
Supporting the motorcycleSince this model is not equipped with a
centerstand, use maintenance stands
when removing the front or rear wheel
or when performing other maintenance
that requires the motorcycle to stand up
right.
Check that the motorcycle is in a stable
and level position before starting any
maintenance.
1. Turn signal light lens
2. Screw
1
2
1. Turn signal light bulb
1
1. Maintenance stand (example)
1
BS2-9-E0.book 37 ページ ２０１６年９月８日　木曜日　午前１１時０分

Index
11-2
1
2
3
4
5
6
7
8
9
101112
Throttle grip free play, checking ........... 7-19
Tires...................................................... 7-19
Tool kit .................................................... 7-2
Traction control system .......................... 3-1
Traction control system indicator light .... 4-7
Traction control system switch ............... 4-4
Troubleshooting .................................... 7-38
Troubleshooting charts ......................... 7-39
Turn signal indicator light........................ 4-5
Turn signal light bulb, replacing ............ 7-37
Turn signal switch ................................... 4-4VValve clearance .................................... 7-19
Vehicle identification number................ 10-1
Vehicle lights ........................................ 7-36WWheel bearings, c hecking .................... 7-32
Wheels.................................................. 7-22
BS2-9-E0.book 2 ページ ２０１６年９月８日　木曜日　午前１１時０分