2017 VOLVO XC90 TWIN ENGINE HYBRID cruise control

DRIVER SUPPORT
}}
307

Pilot Assist overview
Controls
Function buttons and symbols (generic illustration)
Increase set speed or resume Pilot Assist setspeed and distance (time interval) to thevehicle ahead
Press to activate Pilot Assist or put it instandby mode
Change from Pilot Assist to Adaptive CruiseControl
Reduce set speed
Increase the distance (time interval) to thevehicle ahead
Change from Adaptive Cruise Control to PilotAssist
Reduce the distance (time interval) to thevehicle ahead
Function symbol
Distance and target vehicle symbol
Steering assistance symbol

Instrument panel
Speed indication (generic illustration)
Set speed
Speed of the vehicle ahead
Your vehicle's current speed.
See also the article "Pilot assist symbols andmessages" for additional information.
Collision warning
Warning light in the windshield
Pilot Assist can exert brake force that is equiva-lent to approximately 40% of the vehicle's totalbraking capacity.
In situations requiring more brake force than PilotAssist can provide and if the driver does notapply the brakes, an audible signal and warninglight will illuminate in the windshield to alert thedriver to react.

NOTE
Strong sunlight, reflections, extreme light con-trasts, the use of sunglasses, or if the driver isnot looking straight ahead may make the vis-ual warning signal in the windshield difficult tosee.

||
DRIVER SUPPORT
* Option/accessory, for more information, see Introduction.308

WARNING
Pilot Assist only provides warnings for vehi-cles that its radar sensor and camera havedetected. For this reason, a warning may begiven later than expected or not at all. Thedriver should never wait for a warning beforeapplying the brakes.

Head-up-display *
A flashing symbol alerts the driver
If the vehicle is equipped with a head-up display,a flashing symbol in the windshield will alert thedriver.
NOTE
Strong sunlight, reflections, extreme light con-trasts, the use of sunglasses, or if the driver isnot looking straight ahead may make the vis-ual warning signal in the windshield difficult tosee.

Related information
•Pilot Assist* (p. 295)
•Starting and activating Pilot Assist-2(p. 308)
•Changing Pilot Assist-2 speed (p. 310)
•Setting a Pilot Assist-2 time interval (p. 311)
•Changing target vehicles and automaticbraking with Pilot Assist-2 (p. 314)
•Deactivating/resuming Pilot Assist (p. 312)
•Passing Assistance with Adaptive CruiseControl or Pilot Assist-2 (p. 289)
•Pilot Assist-2 limitations (p. 315)
•Pilot Assist-2 symbols and messages(p. 317)
•Adaptive Cruise Control (ACC)* (p. 281)
•Distance Alert* (p. 279)
•Head-up display (HUD)* (p. 122)
•Radar sensor limitations (p. 319)
•Camera limitations (p. 323)
Starting and activating Pilot Assist-2
Pilot Assist has to be started and then activatedbefore it can provide steering assistance andregulate speed and the distance to the vehicleahead.
Function buttons and symbols

DRIVER SUPPORT
}}}}
309

Prerequisites
The prerequisites for activating Pilot Assist are:
•The driver's seat belt must be buckled andthe driver's door must be closed.
•There must be a vehicle ahead (a target vehi-cle) within a reasonable distance or yourvehicle's current speed must be at least9 mph (15 km/h).
With ACC in standby mode:
1.Tap ▶ (6).
>The symbol will change to PilotAssist in standby mode (8).
2.Press the button (2) on the left-sidesteering wheel keypad.
>Pilot Assist will go into active mode andthe current speed will be stored and dis-played in the center of the speedometer.
or
If Adaptive Cruise Control has been started:
–Tap ▶ (6).
>Pilot Assist will start.
Pilot Assist's steering assis-tance is only active when thesteering wheel symbol (2)changes from GRAY to WHITE.
And Pilot Assist will only regulate the time inter-val to the vehicle ahead when a vehicle symbol(1) is displayed above the steering wheel.
At the same time, a speedinterval will be marked.
The higher speed is the onestored by the driver and thelower one is the speed of thevehicle ahead (target vehicle).

WARNING
Pilot Assist is not a collision avoidance sys-tem. The driver is always responsible forsteering or applying the brakes if the systemdoes not detect another vehicle.
Do not use Pilot Assist in demanding drivingconditions such as city driving or other heavytraffic situations, in slippery conditions, whenthere is a great deal of water or slush on theroad, during heavy rain or snow, in poor visibil-ity, on winding roads or on highway on- or off-ramps.
In certain situations, it may be difficult for PilotAssist to assist the driver correctly or to deac-tivate automatically. In such cases, it is advisa-ble not to use Pilot Assist. Examples of suchsituations may be:
•the lane's side market lines are missing,badly faded or cross each other.
•the division of lanes is not clear, e.g.,when a line divides or merges withanother, at exits or if there are many roadsigns/markers.
•there are edges or other lines on or nearthe lane, e.g., curbs, cracks, repairedareas, sharp shadows, etc.
•the lane is narrow or winding.

||
DRIVER SUPPORT
* Option/accessory, for more information, see Introduction.310
•the lane is at the top of a hill, on anuneven road surface or over a bump.
•bad weather conditions (rain, snow, fog,slush, poor visibility, backlighting, etc).
The driver should also be aware that PilotAssist has the following limitations:
•High curbs, barriers and temporary obsta-cles (cones, barriers etc) may not bedetected or could be detected incorrectlyas side marker lines, which may create arisk of collision. The driver must ensure asafe distance to these obstacles.
•The camera or radar sensor may not beable to detect objects if there are pot-holes or if there are stationary objectspartially or completely blocking the road.
•Pilot Assist does not "see" pedestrians,animals, etc.
•Pilot Assist's steering capacity is limitedand may not always be able to help thedriver keep the vehicle in the lane.

Hands on the steering wheel
Pilot Assist only functions when the driver'shands are on the steering wheel, which is con-tinuously monitored by the system. If this is notthe case, the driver will be alerted by a text mes-sage in the instrument panel. If the driver's handsare not returned to the steering wheel, an audiblesignal will sound.
If the driver does not return his/her hands to thesteering wheel after the audible signal, Pilot
Assist will go into standby mode and must be
reactivated by pressing .
Related information
•Pilot Assist* (p. 295)
•Pilot Assist-2* (p. 305)
•Changing Pilot Assist-2 speed (p. 310)
•Setting a Pilot Assist-2 time interval (p. 311)
•Changing target vehicles and automaticbraking with Pilot Assist-2 (p. 314)
•Deactivating/resuming Pilot Assist (p. 312)
•Passing Assistance with Adaptive CruiseControl or Pilot Assist-2 (p. 289)
•Pilot Assist-2 limitations (p. 315)
•Pilot Assist-2 symbols and messages(p. 317)
Changing Pilot Assist-2 speed
Different speeds can be set for Pilot Assist.
Function buttons and symbols
–Change a set speed by pressing the (1)or — (3) buttons briefly or by pressing andholding them:
•Press briefly: changes speed in+/– 5 mph (+/– 5 km/h) increments.Each press changes the vehicle's speedby +/– 5 mph (+/– 5 km/h).
•Press and hold: changes the speed+/– 1 mph (+/– 1 km/h) at a time.Release the button when the set speedindicator (4) has moved to the desiredspeed.
If speed is increased by pressing the accelerator
pedal before the button is pressed, the vehi-cle's speed when the button is pressed will

DRIVER SUPPORT
}}
* Option/accessory, for more information, see Introduction.311
become the set speed assuming that the accel-erator pedal is still depressed when the button ispressed.
A temporary increase in speed, such as whenpassing another vehicle, does not affect thespeed set for Pilot Assist. The vehicle will returnto the set speed when the accelerator pedal isreleased.
Pilot Assist can follow another vehicle from astandstill up to a speed of approx. 125 mph(200 km/h). Always observe posted speed limits.
The lowest speed that can be set/stored for PilotAssist is 20 mph (30 km/h). However, PilotAssist can monitor and react to the speed of thevehicle ahead down to a standstill.
The highest speed that can be set/stored isapprox. 125 mph (200 km/h). Always observeposted speed limits.

Related information
•Pilot Assist* (p. 295)
•Pilot Assist-2* (p. 305)
•Starting and activating Pilot Assist-2 (p. 308)
•Setting a Pilot Assist-2 time interval (p. 311)
•Changing target vehicles and automaticbraking with Pilot Assist-2 (p. 314)
•Deactivating/resuming Pilot Assist (p. 312)
•Passing Assistance with Adaptive CruiseControl or Pilot Assist-2 (p. 289)
•Pilot Assist-2 limitations (p. 315)
•Pilot Assist-2 symbols and messages(p. 317)
Setting a Pilot Assist-2 time interval
Different time intervals to the vehicle ahead canbe selected and are shown in the instrumentpanel as 1–5 horizontal bars.
Changing the time interval
The greater the number of bars,the longer the time interval.One bar between the vehiclesrepresents a time interval ofapproximately 1 second; 5 barsis approximately 3 seconds.

NOTE
When the graphic in the instrument panelshows a vehicle and a steering wheel, PilotAssist is following a vehicle ahead using theset time interval.
If only a steering wheel is displayed, there isno vehicle ahead within a reasonable dis-tance.

||
DRIVER SUPPORT
* Option/accessory, for more information, see Introduction.312
Time interval controls
Press to reduce the time interval to the vehi-cle ahead
Press to increase the time interval to thevehicle ahead
Distance indicator
In order to follow the vehicle ahead as smoothlyas possible, Pilot Assist allows the time interval tovary considerably in certain situations. At lowspeeds, when the distance to the vehicle aheadis short, Pilot Assist increases the time intervalslightly.
•If Pilot Assist does not seem to react when itis put in active mode, this may be becausethe set time interval to the vehicle aheaddoes not allow an increase in speed.
•The higher the speed, the greater the dis-tance to the vehicle ahead for a given timeinterval.

WARNING
•Only use a time interval that is suitable incurrent traffic conditions.
•A short time interval gives the driver lim-ited reaction time if an unexpected situa-tion occurs in traffic.

Related information
•Pilot Assist* (p. 295)
•Pilot Assist-2* (p. 305)
•Starting and activating Pilot Assist-2 (p. 308)
•Changing Pilot Assist-2 speed (p. 310)
•Changing target vehicles and automaticbraking with Pilot Assist-2 (p. 314)
•Deactivating/resuming Pilot Assist (p. 312)
•Passing Assistance with Adaptive CruiseControl or Pilot Assist-2 (p. 289)
•Pilot Assist-2 limitations (p. 315)
•Pilot Assist-2 symbols and messages(p. 317)
Deactivating/resuming Pilot Assist
Pilot Assist can be temporarily deactivated, putin standby mode and then reactivated.
Function buttons and symbols (generic illustration)

Deactivating and putting Pilot Assist in
standby mode
–Press the button (2).
>Pilot Assist will go into standby mode. The
symbol in the instrument panel willchange colors from WHITE to GRAY andthe set speed in the center of the speed-ometer will change from BEIGE to GRAY.
or
–Press the ◀ button (2).
>Pilot Assist will be turned off and shift toAdaptive Cruise Control in active mode.

DRIVER SUPPORT
* Option/accessory, for more information, see Introduction.314
•Changing Pilot Assist-2 speed (p. 310)
•Setting a Pilot Assist-2 time interval (p. 311)
•Changing target vehicles and automaticbraking with Pilot Assist-2 (p. 314)
•Passing Assistance with Adaptive CruiseControl or Pilot Assist-2 (p. 289)
•Pilot Assist-2 limitations (p. 315)
•Pilot Assist-2 symbols and messages(p. 317)
•Distance Alert* (p. 279)
Changing target vehicles andautomatic braking with PilotAssist-2
At certain speeds, Pilot Assist can change targetvehicles and automatically apply the brakes.

Changing target vehicles
If the target vehicle turns suddenly, there may be a sta-tionary vehicle ahead
When Pilot Assist is actively following anothervehicle at speeds under 20 mph (30 km/h) andchanges targets from a moving vehicle to a sta-tionary one, the system will brake for the station-ary vehicle.
WARNING
If Pilot Assist changes targets from a movingvehicle to a stationary one at speeds above20 mph (30 km/h), the system will not reactto the stationary vehicle and will accelerate tothe previously set speed.
The driver must actively apply the brakes toslow/stop the vehicle.

Automatic standby mode when changing
targets
Pilot Assist disengages and goes into standbymode if:
•your vehicle's speed goes below approx.3 mph (5 km/h) and Pilot Assist cannotdetermine if the target object is a stationaryvehicle or some other type of object such asa speed bump, etc
•the vehicle's speed goes below approx.3 mph (5 km/h) and the vehicle aheadchanges lanes or turns so that Pilot Assistno longer has a target vehicle to follow

Auto-hold brake function
In slow-moving, stop-and-go traffic or when stop-ped at a traffic light, driving will resume automati-cally if the vehicle is not stopped for more thanapprox. 3 seconds. If it takes more than3 seconds for the vehicle ahead to begin movingagain, Pilot Assist will go into standby mode andthe auto-hold brake function will activate.

DRIVER SUPPORT
}}
* Option/accessory, for more information, see Introduction.315
–The driver will then have to reactivate PilotAssist in one of the following ways:
•Press the button on the left-sidesteering wheel keypad
•Press the accelerator pedal
>Pilot Assist will resume following the vehi-cle ahead (target vehicle) if it begins tomove within approx. 6 seconds.

NOTE
Pilot Assist can keep the vehicle at a stand-still for up to 5 minutes, after which the park-ing brake will be set and Pilot Assist will gointo standby mode.
The parking brake has to be released beforePilot Assist can be reactivated.

Deactivation of the auto-hold brake function
In certain situations, auto-hold will be deactivatedwhen the vehicle is at a standstill and Pilot Assistwill go into standby mode.
This means that the brakes will be released andthe vehicle can begin to roll.
The driver must actively apply the brakes to keepthe vehicle at a standstill.
This can occur in the following situations:
•the driver presses the brake pedal
•the parking brake is set
•the gear selector is moved to the P, N or Rpositions
•the driver puts Pilot Assist in standby mode
Automatically setting the parking brake
In certain situations, the parking brake is setautomatically to help keep the vehicle at a stand-still.
This occurs if Pilot Assist keeps the vehicle at astandstill with the brakes and:
•the driver unbuckles the seat belt or opensthe door
•Pilot Assist has kept the vehicle at a stand-still for more than approx. 5 minutes
•the engine is turned off
•the brakes overheat

Related information
•Pilot Assist* (p. 295)
•Pilot Assist-2* (p. 305)
•Starting and activating Pilot Assist-2 (p. 308)
•Changing Pilot Assist-2 speed (p. 310)
•Setting a Pilot Assist-2 time interval (p. 311)
•Deactivating/resuming Pilot Assist (p. 312)
•Passing Assistance with Adaptive CruiseControl or Pilot Assist-2 (p. 289)
•Pilot Assist-2 limitations (p. 315)
•Pilot Assist-2 symbols and messages(p. 317)
Pilot Assist-2 limitations
Pilot Assist functionality may be limited in certainsituations.
Pilot Assist is designed to help the driver in anumber of situations. However, the driver alwayshas the primary responsibility for maintaining asafe distance to other vehicles and for keepingthe vehicle in its proper traffic lane.