2017 VOLVO XC90 TWIN ENGINE HYBRID warning

||
DRIVER SUPPORT
282
vehicle set by the driver. If the radar sensor doesnot detect a vehicle ahead, ACC will insteadmaintain the speed set by the driver.
ACC is designed to smoothly regulate speed.However, the driver must apply the brakes in sit-uations that require immediate braking such aswhen there are great differences in speedbetween vehicles, or if the vehicle ahead brakessuddenly. Due to limitations in the radar sensor,braking may occur unexpectedly or not at all.
Adaptive Cruise Control can follow another vehi-cle from a standstill up to 125 mph (200 km/h).Always observe posted speed limits.
The driver can also toggle between ACC andCruise Control (CC) – see the article "Switchingbetween Cruise Control and Adaptive CruiseControl".

WARNING
•It is advisable to read through all of therelated articles pertaining to ACC (seethe list at the end of this article).
•Adaptive Cruise Control cannot cover alldriving situations and traffic, weather androad conditions.
•This system is designed to be a supple-mentary driving aid. It is not, however,intended to replace the driver's attentionand judgement. The driver is responsiblefor maintaining a safe distance and speedand must intervene if Adaptive CruiseControl does not maintain a suitablespeed or suitable distance to the vehicleahead.
•Maintenance of ACC components mayonly be performed by a trained and quali-fied Volvo technician.

Overview
The distance to the vehicle ahead (in the samelane) is monitored by a radar sensor. Your vehi-cle's speed is regulated by accelerating andbraking. The brakes may emit a sound when theyare being modulated by the adaptive cruise con-trol system. This is normal.
WARNING
•Adaptive Cruise Control is not a collisionavoidance system. The driver is alwaysresponsible for applying the brakes if thesystem does not detect another vehicle.
•Adaptive Cruise Control does not react topeople or animals, or small vehicles suchas bicycles and motorcycles. It also doesnot react to slow moving, parked orapproaching vehicles, or stationaryobjects.
•Do not use Adaptive Cruise Control indemanding driving conditions such as citydriving or other heavy traffic situations, inslippery conditions, when there is a greatdeal of water or slush on the road, duringheavy rain or snow, in poor visibility, onwinding roads or on highway on- or off-ramps.

DRIVER SUPPORT
}}
283

Controls
Function buttons and symbols (generic illustration)
Increases the set speed or puts ACC backinto active mode (previous settings will beresumed)
Puts ACC in active mode and stores the cur-rent speed or puts ACC in standby mode
Reduces the set speed
Increases the time interval/distance to thevehicle ahead
Reduces the time interval/distance to thevehicle ahead
Target vehicle indicator: ACC has detectedand is following a target vehicle using the settime interval
Distance/time indicator
Instrument panel
Speed indicators
Set speed
Speed of the vehicle ahead
The current speed of your vehicle
See the article "Adaptive cruise control symbolsand messages" for examples of different combi-nations of symbols, depending on the traffic sit-uation.

Collision warning
Warning light in the windshield
Adaptive Cruise Control can exert brake forcethat is equivalent to approximately 40% of thevehicle's total braking capacity.
In situations requiring more brake force thanACC can provide and if the driver does not applythe brakes, an audible signal from the City Safetysystem will sound and warning light will illuminatein the windshield to alert the driver to react.

NOTE
Strong sunlight, reflections, extreme light con-trasts, the use of sunglasses, or if the driver isnot looking straight ahead may make the vis-ual warning signal in the windshield difficult tosee.

||
DRIVER SUPPORT
* Option/accessory, for more information, see Introduction.284

WARNING
Adaptive Cruise Control only warns of vehiclesdetected by the radar sensor. In some casesthere may be no warning or the warning maybe delayed. The driver should always apply thebrakes when necessary.

Head-up-display *
A flashing light alerts the driver
A flashing icon will appear in the head-up displayto alert the driver of a collision risk.

NOTE
Strong sunlight, reflections, extreme light con-trasts, the use of sunglasses, or if the driver isnot looking straight ahead may make the vis-ual warning signal in the windshield difficult tosee.
Related information
•Starting and activating Adaptive CruiseControl (ACC)* (p. 284)
•Changing Adaptive Cruise Control (ACC)speed (p. 287)
•Setting an Adaptive Cruise Control timeinterval (p. 288)
•Changing target vehicles and automaticbraking with Adaptive Cruise Control (ACC)(p. 289)
•Switching between Cruise Control andAdaptive Cruise Control* (p. 278)
•Passing Assistance with Adaptive CruiseControl or Pilot Assist-2 (p. 289)
•Deactivating/resuming Adaptive CruiseControl (ACC) (p. 285)
•Adaptive Cruise Control (ACC) - trouble-shooting (p. 291)
•Adaptive Cruise Control (ACC) symbols andmessages (p. 293)
•Pilot Assist* (p. 295)
•Distance Alert* (p. 279)
•Head-up display (HUD)* (p. 122)
•Radar sensor limitations (p. 319)
Starting and activating Adaptive
Cruise Control (ACC)*
ACC must first be put in active mode before itcan be started in order to regulate speed or aset time interval to the vehicle ahead.

Starting ACC (putting it in standby
mode)
Function buttons and symbols
–Press ◀ (2) or ▶ (3) to scroll to the ACC
() function. The symbol (4) will be dis-played in the instrument panel.
>The symbol indicates that ACC has beenstarted and is in standby mode. Instandby mode, the vehicle will not main-tain a set speed or a time interval to thevehicle ahead.

||
DRIVER SUPPORT
* Option/accessory, for more information, see Introduction.286

WARNING
When ACC is in standby mode, the driver hasto control the vehicle's speed and distance toa vehicle ahead.
When ACC is in standby mode, the driver willbe alerted if the distance to the vehicle aheadis too short by the Distance Alert function.See the article "Distance Alert" for additionalinformation.

Standby mode due to action by the driver
ACC is temporarily deactivated and put instandby mode if:
•the brakes are applied
•The gear selector is moved to N
•the vehicle is driven faster than the setspeed for more than 1 minute.
In these cases, the driver will have to regulate thevehicle's speed.
A temporary increase in speed, such as whenpassing another vehicle, does not affect the ACCset speed. The vehicle will return to the set speedwhen the accelerator pedal is released.

Automatic standby mode
ACC interacts with other systems, such asElectronic Stability Control. If any of these othersystems are not functioning properly, ACC willturn off automatically.
WARNING
If this happens, the driver will be alerted by anaudible signal and a message in the instru-ment panel. The driver will have to adapt thevehicle's speed, apply the brakes when nec-essary and keep a safe distance to the vehicleahead.
ACC switches automatically to standby mode if:
•the vehicle's speed goes below approx.3 mph (5 km/h) and ACC cannot determineif the vehicle ahead is stationary or is anobject such as a speed bump, etc
•the vehicle's speed goes below approx.3 mph (5 km/h) and the vehicle aheadchanges lanes or turns so that ACC nolonger has a target vehicle to follow
•the driver opens the door
•the driver unbuckles the seat belt
•the engine speed (rpm) is too high/low
•the wheels lose traction
•the brake temperature is too high
•the parking brake is applied
•the stability system's ESC Sport Mode isactivated
•the Off Road drive mode is selected
•The radar sensor is covered by e.g., wet snowor if heavy rain interferes with radar waves
Reactivating ACC from standby mode
Generic illustration
To reactivate ACC after it has temporarily beenput in standby mode:
–Press the button (1).
>The vehicle will then return to the mostrecently set speed.

WARNING
There may be a significant increase in speed
after the button has been pressed.

Related information
•Adaptive Cruise Control (ACC)* (p. 281)
•Starting and activating Adaptive CruiseControl (ACC)* (p. 284)
•Setting an Adaptive Cruise Control timeinterval (p. 288)

DRIVER SUPPORT
* Option/accessory, for more information, see Introduction.288
Setting an Adaptive Cruise Controltime interval
ACC makes it possible to set various time inter-vals to the vehicle ahead.
Different time intervals to thevehicle ahead can be selectedand are shown in the instru-ment panel as 1–5 horizontalbars. The greater the number ofbars, the longer the time inter-val. One bar between the vehi-cles represents a time interval of approximately1 second; 5 bars is approximately 3 seconds.
The same symbol appears if Distance Alert isactivated.
•If the symbol shows two vehicle's, ACC isactively following the vehicle ahead (a targetvehicle).
•If only one vehicle is displayed, ACC is notactively following another vehicle.

Changing a time interval
Controls for setting a time interval
Reduce the time interval
Increase the time interval
Distance/time indicator
–Press buttons (1) or (2) to reduce orincrease the time interval.
>The distance/time indicator (3) shows thecurrent time interval.
In order to follow the vehicle ahead as smoothlyas possible, ACC allows the time interval to varyconsiderably in certain situations. At low speeds,when the distance to the vehicle ahead is short,ACC increases the time interval slightly.
•If ACC does not seem to react when it is putin active mode, this may be because the set
time interval to the vehicle ahead does notallow an increase in speed.
•The higher the speed, the greater the dis-tance to the vehicle ahead for a given timeinterval.
•Only use time intervals permitted by localtraffic regulations.

WARNING
•Only use a time interval that is suitable incurrent traffic conditions.
•A short time interval gives the driver lim-ited reaction time if an unexpected situa-tion occurs in traffic.

Related information
•Adaptive Cruise Control (ACC)* (p. 281)
•Starting and activating Adaptive CruiseControl (ACC)* (p. 284)
•Deactivating/resuming Adaptive CruiseControl (ACC) (p. 285)
•Passing Assistance with Adaptive CruiseControl or Pilot Assist-2 (p. 289)
•Adaptive Cruise Control (ACC) symbols andmessages (p. 293)
•Distance Alert* (p. 279)

DRIVER SUPPORT
}}
* Option/accessory, for more information, see Introduction.289
Passing Assistance with AdaptiveCruise Control or Pilot Assist-2
ACC or Pilot Assist can assist the driver whenpassing other vehicles.

How passing assistance works
When ACC or Pilot Assist is following anothervehicle and the driver indicates that he/she isabout to pass that vehicle by using the left turnsignal, ACC or Pilot Assist will begin acceleratingtoward the vehicle ahead before your vehicle hasmoved into the passing lane.
The function will then delay a speed reduction toavoid early braking as your vehicle approachesthe slower-moving vehicle.
The function is active until your vehicle haspassed the other vehicle.

WARNING
Be aware that this function may be activatedin situations other than when passing a vehi-cle, such as if the turn signal is used to indi-cate a lane change or to indicate a turn. Thevehicle will accelerate briefly.

Using passing assistance
To activate passing assistance:
•Your vehicle (ACC or Pilot Assist) must befollowing another vehicle (the target vehicle).
•Current speed must be at least approx.45 mph (70 km/h ).
•The speed set for ACC or Pilot Assist mustbe high enough to safely pass the vehicleahead.
Starting passing assistance
To start a passing assistance sequence:
•Activate the left turn signal.

Passing assistance limitations
WARNING
The driver should be prepared for suddenchanges when passing assistance is used. Incertain cases, there may be undesired accel-eration.
Certain situations should be avoided, such as:
•If the vehicle is approaching an exit to theleft or a left turn.
•If the vehicle ahead slows down beforeyour vehicle has moved into the passinglane.
•Traffic in the passing lane slows down.
Passing assistance in these situations can bedeactivated by putting ACC or Pilot Assist instandby mode.

Related information
•Pilot Assist* (p. 295)
•Pilot Assist-2* (p. 305)
•Adaptive Cruise Control (ACC)* (p. 281)
Changing target vehicles andautomatic braking with AdaptiveCruise Control (ACC)
At certain speeds, Adaptive Cruise Control canchange target vehicles and automatically applythe brakes.
Changing target vehicles
If the target vehicle turns suddenly, there may be a sta-tionary vehicle ahead
When ACC is actively following another vehicle atspeeds under 20 mph (30 km/h) and changestargets from a moving vehicle to a stationary one,the system will brake for the stationary vehicle.

||
DRIVER SUPPORT
* Option/accessory, for more information, see Introduction.290

WARNING
If ACC changes targets from a moving vehicleto a stationary one at speeds above 20 mph(30 km/h), the system will not react to thestationary vehicle and will accelerate to thepreviously set speed.
The driver must actively apply the brakes toslow/stop the vehicle.

Automatic standby mode when changing
targets
ACC disengages and goes into standby mode if:
•your vehicle's speed goes below approx.3 mph (5 km/h) and ACC cannot determineif the target object is a stationary vehicle orsome other type of object such as a speedbump, etc
•the vehicle's speed goes below approx.3 mph (5 km/h) and the vehicle aheadchanges lanes or turns so that ACC nolonger has a target vehicle to follow.

Auto-hold brake function
In slow-moving, stop-and-go traffic or when stop-ped at a traffic light, driving will resume automati-cally if the vehicle is not stopped for more thanapprox. 3 seconds. If it takes more than3 seconds for the vehicle ahead to begin movingagain, ACC will go into standby mode and theauto-hold brake function will activate.
–The driver will then have to reactivate ACC inone of the following ways:
•Press the button on the left-sidesteering wheel keypad.
•Press the accelerator pedal.
>ACC will resume following the vehicleahead (target vehicle) if it begins to movewithin approx. 6 seconds.
NOTE
ACC can keep the vehicle at a standstill forup to 5 minutes, after which the parking brakewill be set and ACC will go into standbymode.
The parking brake has to be released beforeACC can be reactivated.

Deactivation of the auto-hold brake function
In certain situations, auto-hold will be deactivatedwhen the vehicle is at a standstill and ACC will gointo standby mode.
This means that the brakes will be released andthe vehicle can begin to roll.
The driver must actively apply the brakes to keepthe vehicle at a standstill.
This can occur in the following situations:
•the driver presses the brake pedal
•the parking brake is set
•the gear selector is moved to the P, N or Rpositions
•the driver puts ACC in standby mode.
Automatically setting the parking brake
In certain situations, the parking brake is setautomatically to help keep the vehicle at a stand-still.
This occurs if ACC keeps the vehicle at a stand-still with the brakes and:
•the driver unbuckles the seat belt or opensthe door
•ACC has kept the vehicle at a standstill formore than approx. 5 minutes
•the brakes overheat
•the engine is turned off.

Related information
•Adaptive Cruise Control (ACC)* (p. 281)
•Auto-hold brake function (p. 379)
•Parking brake (p. 382)

||
DRIVER SUPPORT
296
If the camera and radar sensor cannot detect thelane's side marker lines or a vehicle ahead, PilotAssist goes into standby mode.
When Pilot Assist is in standby mode and yourvehicle comes too close to the vehicle ahead, thedriver will be alerted by the Distance Alert func-tion.

WARNING
•Pilot Assist is designed to be a supple-mentary driving aid and cannot cover alldriving situations, traffic, weather and/orroad conditions.
•The driver should be familiar with all ofthe information in this article regardingPilot Assist, including its limitations.
•Pilot Assist is not intended to replace thedriver's attention and judgement.
•Pilot Assist must only be used wherethere are clearly visible traffic lane sidemarker lines on both sides of the currenttraffic lane. In other circumstances thereis an increased risk of collision with sur-rounding obstacles that are not detectedby the system.
•The driver is always responsible for steer-ing the vehicle and maintaining a suitablespeed and distance to the vehicle aheadand must intervene if necessary, even ifPilot Assist is being used.
Pilot Assist is designed to regulate speedsmoothly but in situations calling for fast braking,the driver must apply the brakes. This applies tosituations where there are considerable differen-ces in speed or if the vehicle ahead brakes sud-denly. Due to the limitations of the camera andradar sensor, the system may apply the brakes inyour vehicle suddenly or not at all.
•The default speed for Pilot Assist is preset toapprox. 30 mph (50 km/h) and cannot bechanged. If the vehicle ahead increasesspeed to over 30 mph (50 km/h) and pullsaway from your vehicle, Pilot Assist will gointo standby mode.

NOTE
•Pilot Assist maintenance should only becarried out by a trained and qualifiedVolvo service technician.
•Pilot Assist regulates your vehicle'sspeed using the accelerator pedal andthe brakes. Please be aware that theremay be a faint sound from the brakeswhen the system is using them.
WARNING
•Pilot Assist is not a collision avoidancesystem. The driver must react if the sys-tem does not detect another vehicle.
•Pilot Assist does not react to people, ani-mals, stationary objects, small vehicles(such as bicycles and motorcycles), lowtrailers and slow moving, parked orapproaching vehicles.
•Do not use Pilot Assist in demandingdriving conditions such as city driving orother heavy traffic situations, in slipperyconditions, when there is a great deal ofwater or slush on the road, during heavyrain or snow, in poor visibility, on windingroads or on highway on- or off-ramps.