2017 TOYOTA YARIS HATCHBACK low beam

732. Instrument cluster
2
Instrument cluster
YARIS_HB_OM_USA_OM52G64U
Warning lights inform the driver of malfunctions in the indicated vehi-
cle’s systems.
Warning lights
*1
(Except Canada)
Brake system warning
light (P. 302)
*1Electric power steering
system warning light
(P. 303)
*1
(Canada)
Brake system warning
light ( P. 302)
*1, 2, 5
PCS warning light
(P. 303)
*1Charging system warn-
ing light ( P. 302)*1, 3Slip indicator
(P. 304)
*1
Low engine oil pressure
warning light ( P. 302)
*2
(Yellow)
Automatic High Beam
indicator (P. 304)
*1
(Red)
High engine coolant
temperature warning
light (P. 302)*2
(Yellow)
Cruise control indicator
(P. 304)
*1
(Except Canada)
Malfunction indicator
lamp ( P. 302)
*2
(Yellow)
LDA indicator
(P. 304)
*1
(Canada)
Malfunction indicator
lamp ( P. 302)
*2, 4
(Yellow)
Lane marker indicators
(P. 304)
*1SRS warning light
(P. 303)Open door warning light
( P. 304)
*1
(Except Canada)
ABS warning light
(P. 303)Low fuel level warning
light ( P. 304)
*1
(Canada)
ABS warning light
(P. 303)Driver’s and front pas-
senger’s seat belt
reminder light ( P. 304)
YARIS_HB_OM_USA_OM52G64U.book 73 ページ ２０１６年２月１６日　火曜日　午後３時２０分

742. Instrument cluster
YARIS_HB_OM_USA_OM52G64U
*1: These lights turn on when the engine switch is turned to the “ON” positionto indicate that a system check is being performed. They will turn off after
the engine is started, or after a few seconds. There may be a malfunction
in a system if a light does not come on, or if the lights do not turn off. Have
the vehicle inspected by your Toyota dealer.
*2: If equipped
*3: The light flashes to indicate that the system is operating and come on toindicate a malfunction.
*4: The lights turn on with LDA indicator to indicate a malfunction.
*5: The light flashes to indicate a malfunction.
The indicators inform the driver of the operating state of the vehicle’s
various systems.
*1
(Except Canada)
Tire pressure warning
light ( P. 305)
*1
(Except Canada)
Maintenance required
reminder light ( P. 306)
*1
(If equipped)
Low windshield washer
fluid warning light
(P. 305)
Indicators
Turn signal indicator
(P. 143)*1, 4Eco Driving Indicator
Light ( P. 120)
Headlight high beam
indicator (P. 147)
*2
(Green)
Cruise control indicator
( P. 188)
*2
(Green)
Automatic High Beam
indicator (P. 183)
*2
“SET” indicator
(P. 188)
*2
Front fog light indicator
(P. 148)
*2
(Green)
LDA indicator
( P. 178)
*3
(Blue)
Low engine coolant tem-
perature indicator
*2, 9
(Green)
Lane marker indicators
(P. 179)
YARIS_HB_OM_USA_OM52G64U.book 74 ページ ２０１６年２月１６日　火曜日　午後３時２０分

1494-3. Operating the lights and wipers
4
Driving
YARIS_HB_OM_USA_OM52G64U
Type BTurns the front fog lights
off
Turns the front fog lights
on
■Fog lights can be used when
The headlights are on in low beam.
1
2
YARIS_HB_OM_USA_OM52G64U.book 149 ページ ２０１６年２月１６日　火曜日　午後３時２０分

1594-5. Toyota Safety Sense C
4
Driving
YARIS_HB_OM_USA_OM52G64U
Toyota Safety Sense C
◆PCS (Pre-Collision System)
P. 1 6 5
◆LDA (Lane Departure Alert)
P. 1 7 8
◆Automatic High Beam
P. 1 8 3
: If equipped
The Toyota Safety Sense C consists of the following drive
assist systems and contributes to a safe and comfortable driv-
ing experience:
WARNING
■Toyota Safety Sense C
The Toyota Safety Sense C is designed to operate under the assumption
that the driver will drive safely, and is designed to help reduce the impact to
the occupants and the vehicle in the case of a collision or assist the driver in
normal driving conditions.
As there is a limit to the degree of recognition accuracy and control perfor-
mance that this system can provide, do not overly rely on this system. The
driver is always responsible for paying attention to the vehicle's surround-
ings and driving safely.
sec_04-05.fm 159 ページ ２０１６年２月１７日　水曜日　午前１１時３５分

1844-5. Toyota Safety Sense C
YARIS_HB_OM_USA_OM52G64U
When all of the following conditions are fulfilled, high beam will be
automatically turned on:
●Vehicle speed is above approximately 25 mph (40 km/h).
● The area ahead of the vehicle is dark.
● There are no oncoming or preceding vehicles with headlights or tail
lights turned on.
● There are few streetlights on the road ahead.
If any of the following conditions are fulfilled, high beam will be auto-
matically turned off:
● Vehicle speed drops below approximately 19 mph (30 km/h).
● The area ahead of the vehicle is not dark.
● Oncoming or preceding vehicles have headlights or tail lights
turned on.
● There are many streetlights on the road ahead.
■Switching to low beam
Pull the lever to original posi-
tion.
The Automatic High Beam indi-
cator will turn off.
Push the lever away from you to
activate the Automatic High
Beam system again.
High beam automatic turning on or off conditions
Turning the high beam on/off manually
sec_04-05.fm 184 ページ ２０１６年２月１７日　水曜日　午前１１時３５分

1854-5. Toyota Safety Sense C
4
Driving
YARIS_HB_OM_USA_OM52G64U■
Switching to high beam
Press the Automatic High
Beam switch.
The Automatic High Beam indi-
cator will turn off and the Head-
light high beam indicator will
turn on.
Press the switch to activate the
Automatic High Beam system
again.
■
The Automatic High Beam can be operated when
The power switch is in ON mode.
■ Front sensor detection information
●High beam may not be automatically turned off in the following situations:
• When oncoming vehicles suddenly appear from a curve
• When the vehicle is cut in front of by another
• When oncoming or preceding vehicles are hidden from sight due to
repeated curves, road dividers or roadside trees
● High beam may be turned off if an oncomi ng vehicle that is using fog lights
without using the headlights is detected.
● House lights, street lights, red traffic signals, and illuminated billboards or
signs may cause the high beam to turn off.
● The following factors may affect the amount of time taken to turn high beam
on or off:
• The brightness of headlights, fog lights, and tail lights of oncoming and
preceding vehicles
• The movement and direction of oncoming and preceding vehicles
• When a oncoming or preceding vehicle only has operational lights on one side
• When a oncoming or preceding vehicle is a two-wheeled vehicle
• The condition of the road (gradient, curve, condition of the road surface, etc.)
• The number of passengers and amount of luggage
sec_04-05.fm 185 ページ ２０１６年２月１７日　水曜日　午前１１時３５分

1864-5. Toyota Safety Sense C
YARIS_HB_OM_USA_OM52G64U●
High beam may be turned on or off when unexpected by the driver.
● In the situations below, the system may not be able to correctly detect the
surrounding brightness levels, and may flash or expose nearby pedestrians
to the high beam. Therefore, you should consider turning the high beams on
or off manually rather than relying on the Automatic High Beam system.
• In bad weather (rain, snow, fog, sandstorms, etc.)
• The windshield is obscured by fog, mist, ice, dirt, etc.
• The windshield is cracked or damaged.
• The front sensor is deformed or dirty.
• The front sensor temperature is extremely high.
• Surrounding brightness levels are equal to those of headlights, tail lights
or fog lights.
• Vehicles ahead have headlights or tail lights that are either switched off, dirty, are changing color, or are not aimed properly.
• When driving through an area of intermittently changing brightness and
darkness.
• When frequently and repeatedly driving ascending/descending roads, or roads with rough, bumpy or uneven surfaces (such as stone-paved
roads, gravel tracks, etc.).
• When frequently and repeatedly taking curves or driving on a winding road.
• There is a highly reflective object ahead of the vehicle, such as a sign or a mirror.
• The back of a vehicle ahead is highly reflective, such as a container on a
truck.
• The vehicle’s headlights are damaged or dirty.
• The vehicle is listing or titling, due to a flat tire, a trailer being towed, etc.
• The driver believes that the high beam may be causing problems or dis- tress to other drivers or pedestrians nearby.
■ If the Automatic High Beam indicator comes on in yellow
It may indicate a malfunction in the system. Contact your Toyota dealer.
■ Temporarily lowering sensor sensitivity
The sensitivity of the sensor can be temporarily lowered.
Turn the engine switch off while the following conditions are met.
• The headlight switch is in .
• The headlight switch lever is in low beam position.
• Automatic High Beam switch is on.
Turn the engine switch to the “ON” position.
Within 30 seconds after , repeat pulling the headlight switch lever to the
original position then pushing it to the high beam position quickly 10 times,
then leave the lever in high beam position.
If the sensitivity is changed, the Automatic High Beam indicator is turn on
and off 3 times.
Automatic High Beam (headlights) may turn on even the vehicle is stopped.
1
2
32
4
sec_04-05.fm 186 ページ ２０１６年２月１７日　水曜日　午前１１時３５分

1874-5. Toyota Safety Sense C
4
Driving
YARIS_HB_OM_USA_OM52G64U
WARNING
■Limitations of the Automatic High Beam
Do not rely on the Automatic High Beam. Always drive safely, taking care to
observe your surroundings and turning high beam on or off manually if nec-
essary.
NOTICE
■Notes when using the Automatic High Beam system
Observe the following to ensure that the Automatic High Beam functions
correctly.
●Do not overload the vehicle.
● Do not modify the vehicle.
sec_04-05.fm 187 ページ ２０１６年２月１７日　水曜日　午前１１時３５分