2017 SUBARU LEGACY brake

4
start/stop engine
To start engine:
STEP1: Carry the access key, and sit in the driver’s seat.
STEP2: Apply the parking brake.
STEP3: Shift the select lever in the P position.
STEP4: Depress the brake pedal until the indicator on
the push-button ignition switch turns green.
STEP5: While depressing the brake pedal, press the
push-button ignition switch.
To stop engine:
STEP1: Stop the vehicle completely.
STEP2: Move the select lever to the P position .
STEP3: Press the push-button ignition switch.
Every time the button is pressed without depressing the brake pedal, the\
power is switched
in the sequence of OFF
➞ACC
➞ON
➞OFF
.
OFF ( Tu r n e d o f f ) ACC (Orange) ON (Orange)
Change of the power supply (Without starting engine)
The key can be turned from ACC to LOCK
only when the key is pushed in while turning
it (all models) and the select lever is in the P
position (CVT models).
Push-button ignition switch (if equipped)
Electronic parking brake switch Ignition switch (if equipped)
*The design may be slightly different from the illustration
depending on the models.
Operation indicator
Apply
Release
X Some functions are available on certain models.
X For detailed operating and safety information, please refer to your Own\
er’s Manual.

5
You must raise the slider and hold it in that position
before you can move the shift lever to the R position.
To change gears, fully depress the clutch pedal, move
the shift lever, and gradually let up on the clutch pedal. Shift paddle:
Gearshifts can be performed using the shift paddle
behind the steering wheel.
o perate s elect lever/ shift lever
M = Manual mode:
With the vehicle either moving or stationary, move the
select lever from the D position to the M position to
select the manual mode.
Continuously variable transmission (if equipped)
Manual transmission (if equipped)
With the brake pedal depressed, shift while
pressing the button in
Shift while pressing the button in
Shift without pressing the button
Select lever button
Downshift Upshift

10
Located on the edge of each rear door.
When the lever is in the LOCK position, the rear door
cannot be opened from the inside. Deactivate the Hill Holder function when:
• Towing a trailer
• Carrying a heavy load
• When you do not frequently stop your vehicle on an
uphill slope using the parking brake.
1
To lower:
Push the upper part of the anchor and slide it down.
2
To raise:
Slide the anchor up.
Tilting
Sliding
Moonroof switch (if equipped)
1
Raise
2
Lower
1
Open
2
Close
Child safety locks
Hill Holder switch
Front seat shoulder belt anchor height
*The design may be slightly different from the
illustration depending on the models.
21
2
1
2
1
Activate/
Deactivate
u Some functions are available on certain models.
u For detailed operating and safety information, please refer to your Own\
er’s Manual.

15
When there is the risk of a rear-end collision with an obstacle in front, the EyeSight
system helps to minimize or prevent a collision by warning the driver. If the driver still
does not take evasive action to avoid a collision, the brakes can be automatically applied
just before the collision in order to reduce impact damage, or if possible, prevent the
collision. If the driver takes evasive action to avoid a collision, Pre-Collision Brake Assist
will operate in order to help the driver to prevent the collision.
Pre-Collision Braking System
Lane Departure Warning OFF switch (Models with EyeSight system)G
Press and hold this switch for approximately 2
seconds or longer to turn off the Lane Departure
Warning and Lane Sway Warning functions.
Pre-Collision Braking System OFF switch (Models with EyeSight system)H
Press and hold this switch for approximately 2
seconds or longer to turn off the Pre-Collision
Braking System and Pre-Collision Throttle
Management.
When vehicle speed is approximately 50 km/h (30 MPH) or more, this function warns
the driver if the system detects that the vehicle is likely to depart the traffic lane.
Lane Departure Warning

17
Some warning/indicator lights illuminate for a few seconds in order to check themselves
when the ignition switch is turned ON.
Main W aR ninG an D inDicato R LiGH ts
Warning lights
Refer to your Owner’s Manual for countermeasures when each warning light comes on.
If necessary, consult your authorized SUBARU dealer.
Seatbelt warning
Remind the driver to fasten
seatbelt.
Front passenger’s seatbelt warning
Remind the front passenger to
fasten seatbelt. Location: next to
overhead console.
Oil pressure warning
The engine oil pressure is too
low.
Engine low oil level warning
The engine oil level decreases to
the lower limit.
All-wheel drive warning (CVT models)
Tires of different diameter fitted/
air pressure excessively low.
SRS airbag system warning
SRS airbag system and/
or seatbelt pretensioners
malfunction.
Power steering warning
The electric power steering
system malfunction.
AT OIL TEMP warning (CVT models)
Transmission fluid temperature
is too hot./Transmission control
system malfunction.
Brake system warning
Electronic parking brake system malfunction/Brake fluid level/EBD System
malfunction (Anti-lock brake system warning light illuminates simultaneously).
Malfunction indicator (Check Engine)
Engine/Emission control system
malfunction.
Charge warning
Charging system malfunction.
Low fuel warning
Fuel tank is nearly empty. Refill
fuel immediately.
High beam assist warning
The high beam assist function
malfunction.

18
Automatic headlight beam leveler warning
Automatic headlight beam leveler malfunction.
Access key warning
The access key is not inside the vehicle. For other situations, refer to your
Owner’s Manual.
ABS warning
Anti-lock Brake System malfunction/EBD System malfunction.
(Brake System warning light illuminates simultaneously).
Windshield washer fluid warning
The fluid level in the windshield washer fluid tank decreases to the lower limit.
BSD/RCTA warning
Blind Spot Detection/Rear Cross Traffic Alert (BSD/RCTA) malfunction.
Vehicle Dynamics Control warning/Vehicle Dynamics Control operation indicator
Warning : Vehicle Dynamics Control system malfunction.
Indicator : Flashes during activation of the skid suppression function and the
traction control function.
Icy road surface warning screen
When the outside temperature becomes 3°C (37°F) or less, the icy road surface
warning screen interrupts to inform the driver that the road surface may be
frozen.
RAB warning
Reverse Automatic Braking System malfunctions.
u Some functions are available on certain models.
u For detailed operating and safety information, please refer to your Own\
er’s Manual.

19
indicator lights
The following indicators show the current status of your car. Refer to your Owner’s Manual
for more information.
Turn signal
indicatorHeadlight
indicatorHigh beam
indicator
Front fog light
indicatorSecurity
indicatorDoor open
indicator
BSD/RCTA OFF
indicatorCruise control
indicatorCruise control
set indicator
Hill Holder indicatorHill descent control indicator
High beam assist indicator
Steering responsive fog lights
OFF indicator
Front passenger’s frontal
airbag ON/OFF indicator
Sonar audible alarm OFF
indicator
Pre-Collision Braking System
OFF indicator
Electronic parking brake
indicator
Vehicle Dynamics Control OFF
indicator
RAB OFF indicator
Lane Departure Warning OFF
indicator