2017 Peugeot 301 change time

9
As a passenger, if you avoid connecting your
multimedia devices (film, music, video game
etc.), you will contribute towards limiting the
consumption of electrical energy, and so of
fuel.
Disconnect your portable devices before
leaving the vehicle.
Eco-driving
Eco-driving is a range of everyday practices that allow the motorist to optimise their fuel consumption and CO2 emissions.
Optimise the use of your
gearbox
With a manual gearbox, move off gently,
change up without waiting and drive by
changing up quite soon.
With an automatic or electronic gearbox, stay
in Drive D or Auto A, according to the type
of gearbox, without pressing the accelerator
pedal heavily or suddenly.
The gear efficiency indicator invites you to
engage the most suitable gear: as soon as the
indication is displayed in the instrument panel,
follow it straight away.
For vehicles fitted with an electronic or
automatic gearbox, this indicator appears only
in manual mode.
Drive smoothly
Maintain a safe distance between vehicles,
use engine braking rather than the
brake pedal, and press the accelerator
progressively. These practices contribute
towards a reduction in fuel consumption and
CO
2 emissions and also help to reduce the
background traffic noise.
If your vehicle has cruise control, make use of
the system at speeds above 25 mph (40 km/h)
when the traffic is flowing well.
Control the use of your electrical
equipment
Before moving off, if the passenger
compartment is too warm, ventilate it by
opening the windows and air vents before
using the air conditioning.
Above 30 mph (50 km/h), close the windows
and open the air vents.
Remember to make use of equipment that can
help keep the temperature in the passenger
compartment down (window blinds, etc.). Switch off the headlamps and fog lamp when
the level of light does not require their use.
Avoid running the engine before moving off,
particularly in winter; your vehicle will warm up
much faster while driving. Switch off the air conditioning as soon as the
desired temperature is attained.
Switch off the demisting and defrosting
controls, if not automatic.
Switch off the heated seat as soon as
possible.
.
Eco-driving

11
Instrument panel for petrol - Diesel
Dials
1Rev counter (x 1,000 rpm).
2 Display screen.
3 Speedometer (mph or km/h).
4 Momentary information reminder:
on servicing,
remaining driving range with the
emissions fluid (AdBlue
®).
Reset the selected function to zero (trip
distance recorder or service indicator).
Setting the time.
Display screen
A Electronic or automatic gearbox
information.
Gear change indicator.
B Time.
C Range related to the fuel or theAdBlue
®
and the SCR system (km).
or
Trip distance recorder.
D Fuel gauge / Diesel preheater.
E Service indicator (miles or km)
then,
Odometer.
These two functions are displayed
successively when switching on the
ignition.
F Cruise control or speed limiter setting.
1
Instruments

31
Date and time adjustment
Instrument panelAudio system / Bluetooth
With PEUGEOT Connect
Radio
Operate the left-hand button on the instrument
panel in the following order:
F

P
ress the button for more than two
seconds: the minutes flash.
F

P
ress the button to increase the minutes.
F

P
ress the button for more than two
seconds: the hours flash.
F

P
ress the button to increase the hours.
F

p
ress the button for more than two
seconds: 24H or 12H is displayed,
F

P
ress the button to select 24H or 12H.
F

P
ress the button for more than two
seconds to complete the adjustments.
The usual screen displays again when the
button hasn't been pressed for approximately
30 seconds. F

P
ress the "MENU" button.
Operate the audio system buttons in the
following order:
F

U
sing the arrows, select the
"Personalisation- Configuration" menu and
confirm by pressing the control knob.
F

U
sing the arrows, select the "Screen
configuration" menu then confirm.
F

U
sing the arrows, select the "Set date and
time" menu then confirm. F

S
elect the setting then confirm.
F
M
odify the setting then confirm again to
save the change.
F
A
djust the settings one by one, confirming
each time.
F
S
elect the "OK" tab in the screen and
confirm to exit the "Set date and time"
menu.
F
Sel
ect the Settings menu.
F

Sel
ect "Date " or "Time ".
F

C
hoose the display formats.
F

C
hange the date and/or time using the
numeric keypad.
F

C
onfirm with "OK".
F

Sel
ect "Date and time ".
1
Instruments

32
With PEUGEOT Connect
Nav
Adjustment of the time and date is only
available if synchronisation when the GPS is
deactivated.
F

Sel
ect the Settings menu.
F

P
ress the " OPTIONS " button to go to the
secondary page.
F

Sel
ect "Setting the time- date".
F

Sel
ect the " Date" or "Time " tab.
F

A
djust the date and/or time using the
numeric keypad.
F

C
onfirm with " OK".Additional adjustments
You can choose:
To change the display format of the date and
t i m e (12 h / 24 h).
To change the time zone.
Activate or deactivate the synchronisation with
the GPS (UTC).
The system does not automatically
manage the change between winter and
summer time (depending on country).
The change between winter and summer
time is done by changing the time zone.
Instruments

35
On-board computer, some definitions
Range
(k m)
The number of kilometres which
can be covered with the fuel
remaining in the tank. Related
to the average fuel consumption
over the last few kilometres
travelled.
This value may vary following a change in
the style of driving or the relief, resulting
in a significant change in the current fuel
consumption.
When the range falls below 20 miles (30 km),
dashes are displayed. After filling with at least
5 litres of fuel, the range is recalculated and is
displayed if it exceeds 60 miles (100 km).
If dashes are displayed continuously while
driving in place of the digits, contact a
PEUGEOT dealer or a qualified workshop.
Current fuel consumption
(l/100 km or km/l)
Calculated over the last few
seconds.
This function is only displayed from
20 mph (30 km/h).
Average fuel consumption
(l/100 km or km/l)
Calculated since the last time the
trip was reset.
Average speed
(km/h)
Calculated since the last time the
trip was reset.
Distance travelled
(k m)
Calculated since the last time the
trip was reset.
Time counter Stop & Start
If your vehicle is fitted with Stop &
Start, a time counter calculates the
time spent in STOP mode during a
j o u r n ey.
It resets to zero every time the
ignition is switched on.
(minutes / seconds or hours / minutes)
1
Instruments

68
Front windscreen wipers
Fast wiping (heavy rain).
Normal wiping (moderate rain).
Intermittent wiping (proportional to
the speed of the vehicle).
Stop.
Raise or lower the control to the desired
position to change the wiping speed.
Single wipe (press down and
release).
Front windscreen wash
Pull the wiper control lever towards you. The
windscreen washer and then the wiper operate
for a fixed time.The screenwash jets are not adjustable.
Do not try to move them (risk of damage).
Special position of the
windscreen wipers
This position permits release of the windscreen
wiper blades.
It is used for cleaning or replacement of the
wiper blades. It can also be useful, in winter, to
release the wiper blades from the windscreen.
F

I
n the minute following ignition switch-off,
any operation of the wiper control stalk will
position the wiper blades vertically.
F

T
o park the wiper blades again, switch on
the ignition and operate the wiper stalk.
To maintain the effectiveness of the wiper
blades, it is advisable to:
-

h

andle them with care,
-

c

lean them regularly using soapy
water,
-

a

void using them to retain cardboard
on the windscreen,
-

r

eplace them at the first signs of wear.
Wiper control stalk
Lighting and visibility

74
Tyre under-inflation detection
System which automatically checks the
pressures of the tyres while driving.
The system monitors the pressures in the four
tyres, once the vehicle is moving.
It compares the information given by the four
wheel speed sensors with reference values,
which must be reinitialised ever y time the
tyre pressures are adjusted or a wheel
changed.
The system triggers an alert as soon as it
detects a drop in the inflation pressure of one
or more tyres.Under-inflation alert
The under-inflation detection system does
not replace the need for vigilance on the
part of the driver.
This system does not avoid the need to
check the tyre pressures (including the
spare wheel) every month as well as
before a long journey.
Driving with under-inflated tyres worsens
road-holding, lengthens braking distances,
causes premature wear of the tyres,
particularly in adverse conditions (heavy
loads, high speeds, long journeys). Driving with under-inflated tyres
increases fuel consumption.
The inflation pressures defined for your
vehicle can be found on the tyre pressure
label.
For more information on the
Identification markings , refer to the
corresponding section.
Checking tyre pressures
This check should be done when the tyres
are "cold" (vehicle stopped for 1 hour or
after a journey of less than 6 miles (10 km)
at moderate speeds).
Other wise, add 0.3 bar to the pressures
shown on the label. This warning is indicated by
continuous illumination of the light,
an audible signal and a message
displayed on the screen.
F
R
educe speed immediately, avoid
excessive steering movements and sudden
braking.
F
S
top as soon as it is safe to do so.
The loss of pressure detected does not
always cause visible bulging of the tyre.
Do not rely on a simple visual check.
F I f you have a compressor (such as the
one in the temporary puncture repair kit),
check the pressures of the four tyres when
cold. If it is not possible to make this check
immediately, drive carefully at reduced
speed.
or
F

I
n the event of a puncture, use the
temporary puncture repair kit or the spare
wheel (depending on equipment).
The warning remains active until the
system is reinitialised.
Safety

108
Automated mode
F Select position A.
You can change mode at any time by
moving the gear selector from A to M or
the other way round.
Moving vehicle, never select the neutral N .
The instrument cluster displays
AUTO
along with the gear engaged.
The gearbox is then operating in auto-active
mode, without any action on the part of the
driver. It continuously selects the most suitable
gear for adapted to the following parameters:
-
o

ptimisation fuel consumption,
-

t
he style of driving,
-

r
oad conditions,
-

v
ehicle load.
For optimum acceleration, when overtaking
another vehicle for example, press the
accelerator pedal fully down, beyond the point
of resistance.
Manual mode
F Select position M .
Moving vehicle, never select the neutral N .
You can change mode at any time by
moving the gear selector from M to A or
the other way round. The gears engaged appear in turn in
the instrument cluster.
The shift requests are taken into account only if
the engine speed allows.
It is not necessary to release the accelerator
when changing gear.
When braking or slowing down, the gearbox
changes down automatically to allow the
vehicle to accelerate in the correct gear.
Under full acceleration, unless the engine is
close to its maximum speed, gear upshift will
only take place when the driver operates the
gear selector.
Reverse gear
To engage reverse gear, the vehicle must be
immobilised with your foot on the brake pedal.
F
Sel
ect position R .
There is an audible signal upon
engagement of reverse.
At low speed, if reverse gear is requested,
the N indicator flashes and the gearbox goes
into neutral automatically.
To engage reverse, put the gear selector into
position N , then to position R .
Driving