2017 Peugeot 208 instrument panel

112
Electronic gearbox
5-speed
R.Reverse.
N. Neutral.
A. Automatic mode.
M. Manual mode.
6-speed
R.Reverse.
N. Neutral.
A. Automatic mode.
M. Manual mode. You can change from position A to M and
from M to A at any time.
Automatic mode
This mode allows gear changing
without action by the driver.
Moving off
Lever at position N
.
F
P
ress the brake pedal firmly.
F

S
tart the engine.
F

P
lace the lever at A or R .
F

R
elease the brake pedal and press the
accelerator pedal progressively.
If the engine does not start:
-
If N is flashing in the instrument panel, move
the gear lever to position A then to position
N .
-

I
f the Foot on the brake message is
displayed, press the brake pedal firmly.
The A , R or N position of the lever is indicated
in the display.
Stopping – Moving off on a slope
Do not use the accelerator to hold the vehicle,
but apply the parking brake.
Stopping – Parking
Place the lever at N and apply the parking
brake.
Manual gear change
This one-off gear change makes it possible
to overtake, for example, while remaining in
automated mode.
F

O
perate the steering mounted control
paddles + or - .
The gearbox engages the gear selected
if engine speed allows it. AUTO remains
displayed on the instrument panel.
After a few moments with no action on the
control paddles, the gearbox returns to
automatic operation.
Driving

113
Manual mode
This mode allows manual sequential gear
changing.
F
M
ove the selector lever to M .
F

P
ush the lever for ward to change
up.
F

P
ull the lever back to change
down.
Steering mounted control paddles
F Pull the "+" paddle to change up.
F P ull the "-" paddle to change up.
The gear engaged is indicated in the display.
Creep function
Depending on the engine, the vehicle moves
without pressing the accelerator.
Assistance with low-speed
manoeuvres
With the engine running at idle, parking brake
released and the lever placed at A , M or R, the
vehicle moves off when your release the brake
pedal.
It stops on opening the driver's door. Closing
the door, and putting your foot on the brake
or accelerator pedal allows movement of the
vehicle again. Following disconnection of the battery, you
have to reinitialise the gearbox.
F

S
witch on the ignition.
AUTO and – appear in the
instrument panel.
F
Sel
ect position N
.
F
P
ress the brake pedal firmly.
F
W
ait around 30 seconds until N or a gear
appears in the instrument panel.
F
R
elease the brake pedal.
The gearbox is operational again.
With the ignition on, if this warning
lamp comes on and AUTO flashes,
accompanied by an audible signal
and a message in the screen, this
indicates a gearbox fault.
Have it checked by a PEUGEOT dealer or a
qualified workshop.
6
Driving

114
Automatic gearbox
P.Parking.
R. Reverse.
N. Neutral.
D. Drive (automatic driving).
M. Manual mode.
S. Sport – more active driving.
T Snow – for driving on snowy roads.
Display in the instrument
panel
When you select a position with the lever,
the corresponding lamp is displayed in the
instrument panel.
Foot on the brake warning
Press the brake pedal when this
comes on in the instrument panel.
Automatic mode
This mode allows gear changing
without action by the driver.
Moving off
Parking brake applied.
F
S tart the engine.
F

L
ever at position P or N .
F

P
ress the brake pedal firmly.
F

R
elease the parking brake.
F

P
lace the selector at D or R .
F

R
elease the brake pedal and press the
accelerator pedal progressively.
The vehicle then moves off.
Never leave children unattended in the
vehicle when the engine is running. F

Sel
ect position D for automatic

changing of the gears.
The gearbox then operates in auto-adaptive
mode, without any inter vention on the part
of the driver. It continuously selects the most
suitable gear according to the style of driving,
the profile of the road and the load in the
vehicle.
For maximum acceleration without touching
the lever, press the accelerator pedal down
fully (kick down). The gearbox shifts down
automatically or holds the gear selected until
the maximum engine speed is reached.
When braking, the gearbox shifts down
automatically to provide effective engine
braking.
If you release the accelerator sharply, the
gearbox will not shift to a higher gear for safety
reasons.
Manual mode
This mode allows manual sequential
gear changing.
F

M

ove the gear lever to M .
Driving

115
F Push the lever for ward to change up.
F

P
ull the lever back to change
down.
Invalid value
This symbol is displayed if a gear
is not engaged correctly (selector
between two positions).
You can change from position D to M and
M to D at any time.
If position R , D or M is selected when the
engine is running at idle, with the brakes
released, the vehicle moves even without
the accelerator being pressed.
Never leave children unattended in the
vehicle when the engine is running.
When carrying out maintenance with the
engine running, apply the parking brake
and select position P . Never select position N while the vehicle
is moving.
Never select position P or R unless the
vehicle is completely stationary.
If position N is selected inadvertently while
driving, allow the engine to return to idle,
then select position D to accelerate.
If the temperature is below -23°C, the
engine should be left at idle for four
minutes, to ensure the correct operation
and life of the engine and gearbox.
Sport programme
This special programme completes the
automatic operation of the gearbox in certain
circumstances.
F

W
ith the engine running, press
button S.
The gearbox automatically favours a dynamic
style of driving.
S appears on the instrument panel.
Snow program
This special program completes the automatic
operation and makes it easier to move off and
make progress in conditions of poor grip.
F

W
ith the engine running, press
the T button.
The gearbox adapts to driving on slippery
roads.
T appears on the instrument panel.
Return to automatic
operation
F Press the button again at any time to quit the program and
return to auto-adaptive mode.
Stopping – Parking
Before switching off the engine.
F M ove the lever to position P or N .
F

A
pply the parking brake.
F

Imm
obilise the vehicle.
6
Driving

117
On BlueHDi Diesel versions with manual
gearbox, in certain driving conditions the
system may suggest changing into neutral so
that the engine can go into standby (STOP
mode with Stop & Start). In this case, N is
displayed in the instrument panel.Example:
-

Y
ou are in third gear.
-

Y
ou press the accelerator pedal.
-

T
he system may suggest that you engage a
higher gear.
The system adapts its gear shift
recommendation according to the driving
conditions (slope, load, etc.) and the
driver’s requirements (power, acceleration,
b r a k i n g , e t c .) .
The system never suggests:
-
e

ngaging first gear,
-
enga

ging reverse gear,
-
enga

ging a lower gear. On vehicle fitted with a manual gearbox,
the arrow may be accompanied by the
gear recommended.Hill start assist
System that holds your vehicle for around
2
seconds, the time to move your foot from the
brake pedal to the accelerator.
The hill start assist function cannot be
deactivated. However, use of the parking
brake to immobilise the vehicle interrupts
its function.
The information appears on the instrument
panel in the form of an arrow.
Uphill, with the vehicle stationar y, it will
briefly stop the vehicle from rolling back
when you release the brake pedal.
With an electronic gearbox, if you are in
position A.
With an automatic gearbox, if you are in D .
6
Driving

118
Hill start assist is only available when:
- y our foot on the brake pedal fully
immobilises the vehicle,
-

c
ertain conditions of gradient are met,
-

w
ith the driver’s door closed.
Downhill, with the vehicle stationary and
reverse gear engaged, the vehicle is held
for a shor t time when you release the brake
pedal.
Do not leave the vehicle while it is being
held temporarily by hill start assist.
If you need to leave the vehicle with the
engine running, apply the parking brake
manually. Then ensure that the parking
brake warning lamp lights up constantly on
the instrument panel.
Operating fault
The fixed illumination of these
warning lamps indicates a fault with
the system.
Have the system checked by a
PEUGEOT dealer or a qualified
workshop.
Stop & Start
The system puts the engine temporarily into
standby – STOP mode – during stops in the
traffic (red lights, traffic jams, etc.). The engine
restarts automatically – START mode – as
soon as you wish to leave again. Restarting
occurs instantaneously, quickly and silently.
Per fect for urban use, the Stop & Start system
reduces fuel consumption and exhaust
emissions as well as the noise level when
stationary.
STOP mode
The " ECO" warning lamp illuminates
in the instrument panel and the
engine goes into standby.
With e- HDi or BlueHDi Diesel and an
electronic gearbox :
-

S

peed below 4 mph (6 km/h).
-

G

ear lever in position N.
Or
-
B

rake pedal pressed.
Driving

121
Operating fault
In the event of a fault with the system, the ECO
OFF switch warning lamp flashes then comes
on fixed.
Have it checked by a PEUGEOT dealer or a
qualified workshop.
If a fault occurs in STOP mode, the vehicle
may stall. All of the instrument panel warning
lamps come on. It is then necessary to switch
the ignition off and to restart the engine using
t h e key.The Stop & Start system requires a
12
V battery of specific technology and
specification.
All work on this type of battery must be
carried out only by a PEUGEOT dealer or
a qualified workshop.
For more information on the 12
V batter y,
refer to the corresponding section.
Speed limiter "LIMIT"
The system prevents the vehicle from
exceeding the speed setting programmed by
the driver.
Steering mounted controls
1. Speed limiter mode selection / off.
2. Increases the set value.
3. Decreases the set value.
4. Speed limiter On / Pause. The vehicle responds to the accelerator until
resistance is felt in the pedal, which signifies
that the vehicle has reached the limiter speed
setting.
However, pressing the pedal beyond this point
of resistance to the floor permits exceeding
of the programmed speed. To resume use of
the limiter, simply reduce the pressure on the
accelerator pedal gradually and return to a
speed below that programmed.
Setting and operation of the system can be
done stationar y with the engine running or
when driving.
Selection
F Place the thumbwheel at the "LIMIT"

position: the speed limiter mode is selected
but is not switched on (PAUSE).
Switching the speed limiter on is not required to
set the speed limit.
The speed setting is selected with the engine
running, stationary or when driving. The
minimum speed setting possible is 20

mph
(30


km/h).
6
Driving

126
When changing the programmed
reference speed by means of a maintained
press, pay attention as the speed can
increase or decrease rapidly.
Do not use the cruise control on slippery
roads or in heavy traffic.
On a steep descent, the cruise control will
not be able to prevent the vehicle from
exceeding the registered speed.
The cruise control system cannot in
any circumstances replace the need
to obser ve speed limits or the need for
vigilance on the part of the driver.
To avoid any risk of jamming the pedals:
-
e
nsure that the mat is positioned and
secured to the floor correctly,
-

n
ever place one mat on top of another.Memorising speeds
This function allows speeds to be saved, which
can then be offered to set the two systems: the
speed limiter (to limit the speed of the vehicle)
or the cruise control (for a vehicle cruising
speed).
You can memorise up to five settings in the
system for each of the two systems.
By default, some speed settings are already
memorised.
With touch screen
This memorisation can be
configured from the menu Driving /
Vehicle .
F

Sel

ect the " Driving functions " tab.
F

Sel

ect the " Adjusting Speeds " function.
F

P

ress " ON" to activate the function.
F

Sel

ect the speed setting 1 to 5 that you want
to change.
F

S

elect the speed setting value you want to
change.
F

E

nter the new value using the numerical
keypad and confirm and click on " OK" to
confirm. As a safety measure, the driver must carry
out these operations when stationary.
Selection
To select a memorised speed:
F
P ress and hold the " +" or " -" button; the
system stops at the nearest memorised
speed.
F

P
ress and hold again the " +" or " -" button to
select another memorised speed.
A reminder of the speed and the state of the
system (on / off) is displayed in the instrument
panel.
Driving