2017 NISSAN ROGUE HYBRID battery

6-2 High-Voltage Battery Pack Removal
6-2.1
Exploded Views
High-Voltage Battery Exploded View : Vehicle front
1.

12-Volt battery positive terminal 2. DC/DC converter 3. High-voltage battery
4. Battery cooling fan bracket 5. Air duct B 6. Battery cooling fan
7. Air duct A 8. Air duct C A. Clip
B. To floor C. Bushing AAYIA0528ZZ
DG–45

6-2.2 Removal Procedure
1. Discharge high-voltage battery. Refer to 3-3 Discharge Procedures (DG–19).
2.

Remove the service plug. Refer to Alternate Procedure 2 (Remove Service Plug) (DG–29).DANGER
Immediately protect the terminals of the disconnected high-voltage harness connector
socket

using insulated tape so that they are not exposed.
3. Fully open back door.
4. Open the storage box lid.
5. Lift rear end of rear luggage board (2)and remove front luggage board belt (1)from rear luggage
board, and then remove rear luggage board.
6. Remove front luggage board fixing clips (A).
7. Lift rear end of front luggage board and slide it towards vehicle rear according to numerical order 12indicated
by arrows as shown in the figure, and then remove
front luggage board. AAYIA0521ZZ
AAYIA0522ZZ
AAYIA0523ZZ
DG–48

13. Loosen high-voltage harness connector nut
(A), then
remove harness clamp (C)and disconnect high-voltage
harness connector (B). DANGER
Touching high-voltage components without wearing
appropriate

Personal Protective Equipment (PPE) will
cause electrocution. DANGER
Immediately protect the terminals of the disconnected high-voltage harness connector
socket

using insulated tape so that they are not exposed.
NOTE:
High-voltage harness connector mounting nut (A) is fixed to the connector to prevent the nut
from dropping. 14. Disconnect harness connector (D)from high-voltage battery, then remove harness clamp (E).DANGER
Immediately protect the terminals of the disconnected high-voltage harness connector
socket

using insulated tape so that they are not exposed.
15. Disconnect 12-volt battery positive terminal (1)from
DC/DC converter using the following step. a. Remove nut (A), then release harness clamp (B)
from high-voltage battery. : Vehicle front
16.

Disconnect DC/DC converter harness connector (A),
then release harness clamp (B).DANGER
Touching high-voltage components without wearing
appropriate

Personal Protective Equipment (PPE) will
cause electrocution. AAYIA0529ZZ
AAYIA0553ZZ
AAYIA0554ZZ
DG–50

20. Remove gas vent hose
(A)from floor panel(B). If gas vent hose is disconnected at the high-voltage
battery

assembly side, this allows easy access to the
inside of high-voltage battery assembly. To prevent this,
always disconnect gas vent hose at the insertion part
on the vehicle body side.
21. Remove bolts (A, B)and high-voltage battery (1). : Vehicle front
DANGER
Touching high-voltage components without wearing
appropriate

Personal Protective Equipment (PPE) will
cause electrocution. To avoid personal injury, when removing
the

high-voltage battery, two people are required.
22. Confirm that the insulated tape is still securely in place on the high-voltage battery.
23. Dismantling the remainder of the Rogue HYBRID may be performed like conventional Nissan vehicles once the
high-voltage system is properly shut down and
discharged.
6-3 High-voltage Battery Recycling
The high-voltage battery is recyclable. For information regarding recycling of the high-voltage battery, it is
recommended you contact the nearest NISSAN dealer or Nissan Consumer Affairs at: United States:
1-800-647-7261 or in Canada: 1-800-387-0122. AAYIA0559ZZ
AAYIA0560ZZ
DG–52