2017 MITSUBISHI L200 engine coolant

The following information is included on themulti information display: odometer, tripme-
ter, average fuel consumption etc.
1- Engine coolant temperature display
® p. 5-06
2- Selector lever position display*
® p. 6-31
3- Speed limiter display* ® p. 6-71
4- Gearshift indicator* ® p. 6-26
5- Fuel remaining display ® p. 5-07
6- Frozen road warning* ® p. 5-06
7- Information display ® p. 5-03
8- Service reminder ® p. 5-07

Refer to “Multi-information display” on page 5-02.
Quick guide
1-20OKTE17E1Overview/Quick guide1

InstrumentsE00500102883
1- TachometerThe tachometer indicates the engine
speed (r/min). The tachometer helps you to obtain more economical driving and
also warns you of excessive engine
speeds (Red zone).
2- Multi-information display ® p. 5-02
3- Speedometer (km/h or mph + km/h)
4- Multi information display switch
® p. 5-03
CAUTIONl When driving, watch the tachometer to make
sure that the engine speed indication does not rise into the red zone (excessive enginerpm).Multi-information display
E00519902630
Always stop the vehicle in a safe place beforeoperating.
The following information is included on the multi information display: odometer, tripme-
ter, average fuel consumption etc.
1- Engine coolant temperature display
® p. 5-06
2- Selector lever position display*
® p. 6-31
3- Speed limiter display* ® p. 6-71
4- Gearshift indicator* ® p. 6-26
5- Fuel remaining display ® p. 5-07
6- Frozen road warning* ® p. 5-06
7- Information display ® p. 5-03
8- Service reminder ® p. 5-07NOTEl When the ignition switch or the operation
mode is OFF, the speed limiter display,
gearshift indicator, selector lever position display, fuel remaining display, engine cool-
ant temperature display and frozen road warning are not displayed.
Instruments
5-02OKTE17E1Instruments and controls5

NOTElWhen the ignition switch or the operation
mode is ON again, the accumulated time
will be reset.Outside temperature display*
E00533501053
This shows the temperature outside the vehi-
cle.
NOTEl The display setting can be changed to the
preferred units (°C or °F).
Refer to “Changing the function settings” on page 5-09.
l Depending on factors such as the driving
conditions, the displayed temperature may vary from the actual outside temperature.Frozen road warning*
E00533401036
If the outside air temperature drops below ap-
prox. 3 °C (37 °F), the alarm sounds and the outside air temperature warning symbol (A)
flashes for about 10 seconds.
CAUTIONl There is a danger the road might be icy, even
when this symbol is not flashing, so please take care when driving.Engine coolant temperature
display
E00533801072
This indicates the engine
coolant temperature.
If the coolant becomes hot, “
” will blink.
Pay careful attention to the engine coolant temperature
display while you are driv-
ing.
CAUTIONl If the engine is overheating, “” will blink.
In this case, the bar graph is in the red zone.
Immediately park the vehicle in a safe place
and take the required measures. Refer to “Engine overheating” on page 8-09.
Multi-information display
5-06OKTE17E1Instruments and controls5

NOTElTo minimize the likelihood of excessive ac-
cumulation of PM, try to avoid driving for long periods at low speeds and repeatedly
driving short distances, and try to keep high
engine speed driving as much as possible.
l The engine sounds slightly different than
usual while the DPF automatically burns
away trapped PM. The change in the engine
sound does not indicate a fault.
DPF warning lamp
The DPF warning lamp comes on in the
event of an abnormality in the DPF system.
If the DPF warning lamp
comes on during vehicle opera- tion
Steady illumination of the DPF warning lamp shows that the DPF has not been able to burn
away all of the trapped PM and that, as a re-
sult, an excessive amount of PM has accumu- lated inside it. To enable the DPF to burn
away the PM, try to drive the vehicle as fol-
lows:
l With the bar graph of engine coolant
temperature display stabilized in roughly
the middle of the scale, drive for approx- imately 20 minutes at a speed of at least
40 km/h (25 mph).

If the DPF warning lamp subsequently stays
on, contact your MITSUBISHI MOTORS
Authorized Service Point.
CAUTIONl You do not have to continuously drive ex-
actly as indicated above. Always strive to
drive safely in accordance with road condi- tions.If the DPF warning lamp flash-
es during vehicle operation
Flashing of the DPF warning lamp indicates an abnormality in the DPF system. Have the system inspected by a MITSUBISHI
MOTORS Authorized Service Point.
CAUTIONl Continuing to drive with the DPF warning
lamp flashing could result in engine trouble and DPF damage.Turbocharger operation*
E00611200083CAUTIONlDo not run the engine at high speeds (for ex-
ample, by revving it or by accelerating rap-
idly) immediately after starting it.
l Do not stop the engine immediately after
high-speed or uphill driving. First allow the
engine to idle to give the turbocharger a
chance to cool down.
Turbocharger operation*
6-22OKTE17E1Starting and driving6

3. Release the clutch pedal. The engine willstop automatically.NOTEl When the engine is automatically stopped,
changes will occur in the driving operations.
Pay close attention to the following.
• The brake booster becomes inoperative
and the pedal effort will increase.
If the vehicle is moving, press down the brake pedal harder than usual.CAUTIONl Observe the following precautions when the
engine is stopped automatically. Otherwise,
an unexpected accident might occur when the engine restarts automatically.CAUTION• Do not depress the accelerator pedal to
race the engine while the vehicle is stop-
ped (regardless of whether the engine is running or stopped).
Otherwise, an unexpected accident might
occur when the engine restarts automati- cally.
• When the engine is automatically stopped,
do not attempt to exit the vehicle. Because
the engine restarts automatically when the driver’s seat belt is unfastened or the driv-
er’s door is opened, an unexpected acci-
dent might occur when the vehicle starts moving.
• Do not move the gearshift lever to a posi-
tion other than the “N” (Neutral) position.
If the gearshift lever is moved to a posi-
tion other than the “N” (Neutral) position, the indication lamp/indicator displayblinks and the buzzer sounds.
If the gearshift lever is returned to the “N” (Neutral) position, the indication lamp
stops blinking and the buzzer stops sound-
ing. The engine will not restart if the gear-
shift lever is in a position other than the “N” (Neutral) position.NOTEl In the following cases, the “AS&G” indica-
tion lamp will blink to inform the driver and
the engine will not stop automatically.
• Driver’s seat belt is not fastened.NOTE•Driver’s door is opened.
• Bonnet is open.
l In the following cases, the “AS&G” indica-
tion lamp will turn off and the engine will
not stop automatically.
• After the engine restarts automatically,
the vehicle speed has not exceeded ap- proximately 5 km/h (3 mph).
• After the engine start, approximately 30
seconds or more have not elapsed.
• After the engine restarts automatically
and the vehicle stops again within 10 sec-
onds.
• Engine coolant temperature is low.
• Ambient temperature is low.
• When the heater is operated, vehicle indi-
cator temperature is not still hot enough.
• Air conditioning is operating and passen-
ger compartment has not sufficientlycooled.
• Demister switch is pressed.
Refer to “Demisting of the windscreen
and door windows: For quick demisting”
on page 7-16.
• When the air conditioner is operated in
the AUTO mode where the temperature
control is set to max. hot or max. cool (for
vehicles with automatic climate air condi- tioning).
• When the diesel particulate filter (DPF)
automatically burns away trapped particu- late matter (PM).
Auto Stop & Go (AS&G) system*
6-24OKTE17E1Starting and driving6

NOTE•Electric power consumption is high, such
as when the rear window demister or oth-
er electrical components are operating or
the blower speed is set to a high setting.
• Battery voltage or battery performance is
low.
• Check engine warning lamp is illuminated
or the
indication lamp is blinking.
• On 4WD vehicles, the drive mode-selec-
tor in “4H” or “4L” (Easy select 4WD),
“4HLc” or “4LLc” (Super select 4WD II).
l In the following cases, the engine will not
stop automatically even if “AS&G” indica-
tion lamp turn on.
• Push the accelerator pedal.
• Brake booster vacuum pressure is low.
• Operate the steering wheel.
• Parking on steep hill.
l Do not rest your foot on the clutch pedal
while driving because this will cause detec-
tion of clutch pedal malfunction and blink-
ing of AS&G OFF display/indicator, and AS&G system will not operate.
l If the AS&G system operates while the air
conditioner is operating, both the engine and
the air conditioning compressor will stop.
Therefore, only the blower will operate, the windows may start to fog up. If this occurs,
press the demister switch to restart the en- gine.
Refer to “Demister switch” on page 7-15.
NOTEl If the windows become fogged up each time
the engine is stopped, we recommend you to
deactivate the AS&G system by pressing the
“AS&G OFF” switch. Refer to “To deacti- vate” on page 6-26.
l If the air conditioner is operating, set the
temperature control higher to lengthen the
time that the engine is stopped automatical- ly.Automatically restarting the
engine
E00627601265
Depress the clutch pedal while the gearshift lever is in the “N” (Neutral) position. The in- dication lamp turns off and the engine restarts
automatically.
NOTEl Do not move the gearshift lever to a position
other than the “N” (Neutral) position or do
not release the clutch pedal while the engine is restarting automatically. The starter motor will stop and the engine will not restart auto-
matically.NOTEl If the engine does not restart automatically
or if the engine stalls, the charge warning lamp and check engine warning lamp will il-
luminate.
If this occurs, the engine will not restart even if the clutch pedal is depressed again. While depressing the brake pedal, fully de-press the clutch pedal and turn the ignition
switch to the “START” position or press the engine switch to start the engine.
For details, refer to “Starting and stopping
the engine” on page 6-17.CAUTIONl In the following cases, the engine will restart
automatically even if the engine was stopped
by the AS&G system. Pay attention, other- wise an unexpected accident might occur
when the engine restarts.
• Vehicle speed is 3 km/h (2 mph) or higher
when coasting down a slope.
• Brake booster vacuum pressure is low be-
cause the brake pedal is depressed repeat- edly or depressed harder than usual.
• Engine coolant temperature is low.
• When the air conditioner is operated by
pressing the air conditioning switch.
• When the preset temperature of the air
conditioner is changed significantly.
Auto Stop & Go (AS&G) system*
6-25OKTE17E1Starting and driving6

2- Rear window demister switch ® p. 5-27
3- Blower speed selection dial
4- Air conditioning switch*
5- Temperature control dial
6- Air selection leverBlower speed selection dial
E00700701321
Select the blower speed by turning the blower speed selection dial clockwise or anticlock- wise.
The blower speed will gradually increase as
the dial is turned to the right.
Temperature control dial
E00700901671
Turn the temperature control dial clockwise
to make the air warmer. Turn it anticlockwise
to make the air cooler.NOTEl While the engine coolant temperature is low,
the temperature of the air from the heaterwill be cool/cold until the engine warms up, even if you have selected warm air with the
lever.Mode selection dial
E00701101364
To change the position of air flowing from
the ventilators, turn the mode selection dial.
(Refer to “Mode selection” on page 7-03.)CAUTIONl When using the mode selection dial between
the “” and “” positions, prevent fog-
ging by moving the air selection lever to se-
lect outside air.
(Refer to “Air selection lever” on page 7-06.)
Heater/Manual air conditioning*
7-05OKTE17E1For pleasant driving7

NOTElIn extreme cold, the air conditioning control
panel screen may operate sluggishly. This does not indicate a problem.
It will disappear when the vehicle interior temperature rises to a normal temperature.Blower speed selection switch
E00702801456
Press of the blower speed selection
switch to increase the blower speed.
Press
of the blower speed selection
switch to decrease the blower speed.
The selected blower speed will be shown in
the display (A).
1- Increase
2- DecreaseTemperature control switch
E00703001859
Press or of the temperature control
switch to the desired temperature.
The selected temperature will be shown in
the display (A).

NOTEl The temperature value of air conditioner is
switched in conjunction with outside tem-
perature display unit of the multi informa- tion display.
Refer to “Changing the temperature unit” on
page 5-10.NOTEl While the engine coolant temperature is low,
the temperature of the air from the heaterwill be cool/cold until the engine warms up, even if you have selected warm air with the
switch.
To prevent the windscreen and windows from fogging up, the ventilator mode will be
changed to “
” and the blower speed will
be reduced while the system is operating in the AUTO mode.
l When the temperature is set to the highest or
the lowest, the air selection and the air con-
ditioner will be automatically changed as follows.
Also, if the air selection is operated manual-
ly after an automatic changeover, manual operation will be selected.
• Quick Heating (When the temperature is
set to the highest setting)
Outside air will be introduced and the air conditioner will stop.
• Quick Cooling (When the temperature is
set to the lowest setting)
Inside air will be recirculated and the air
conditioner will operate.
The settings described above are the factory
settings.
Automatic climate control air conditioner*
7-11OKTE17E1For pleasant driving7 Type 1
Type 2