2017 MITSUBISHI iMiEV lights

Front fog light switch 5-50 Features and controls
5
N00522801433
The front fog lights illuminate only when the headlights are on low beam. Turning the knob in the direction of the “ON”position turns on the front fog lights as well as the indicator in the instrument cluster. To turn them off, turn the knob in the direction ofthe “OFF” position. The knob will return to the neutral position when it is released.
N00523000640
The windshield wiper and washer can be operated with the electric motor switch in the “ON” or “ACC” position.If the blades are frozen to the windshield, do not operate the wipers until the ice has melted
and the blades are freed, otherwise the wiper motor may be damaged. With the lever in the “INT” (speed sensitive intermittent operation) position, the intermit- tent intervals can be adjusted by turning theknob (A).
Front fog light switch
NOTE
 If the headlights are switched to high beam, the front fog lights will
go out; they will illu-
minate again when the headlights areswitched back to low beam.
 If the combination headlights and dimmer switch is rotated to the “OFF” or “ ” posi- tion while the front fog lights are illumi-nated, they will automatically turn off. They can be turned back on again by rotating the combination headlight
s and dimmer switch
back to “ ” position, and turning the knob in the direction of the “ON” position.  Do not use fog lights ex
cept in conditions of
fog, otherwise excessive light glare may temporarily blind oncoming vehicle drivers.
Wiper and washer switch
CAUTION If the washer is used
in cold weather, the
washer fluid sprayed against the glass mayfreeze, which may hinder visibility. Warm the glass with the defroster before using the washer.
Windshield wipers
NOTE
MIST- Misting function
The wipers will operate once.
OFF- OffINT- Intermittent (Speed sensitive) HI- Fast
To adjust intermittent intervals
BK0220401US.book 50 ページ ２０１５年６月３日　水曜日　午前７時４２分

Interior lights
Features and controls 5-77
5
N00525300559 N00525800222
The dome light can be turned on by sliding the dome light switch.Interior lights 1- Dome light (Rear)
 P.5-78
2- Dome light (Fr
ont)/Reading lights
 P.5-77
Dome light (Front)/Reading lights
(if so equipped)
Dome light (Front)

1- Door 2- Off 1- (DOOR)
 The dome light comes on when any door or the liftgate
is opened. It goes
off approximately 30 seconds afterthe door or liftgate is closed (delayed off function). However, the light goes off immediately if:• The door and the liftgate are closed and the electric motor switch is turned to the “ON” position.• The driver’s door is closed after all the other doors are closed while the lock knob of the driver’s door is in the lock position. • The door and the liftgate are closedand the power door lock switch is used to lock the doors. • The keyless entry system remotecontrol transmitter is used to lock the doors.
BK0220401US.book 77 ページ ２０１５年６月３日　水曜日　午前７時４２分

Interior lights 5-78 Features and controls
5
N00553800096
Regardless of the dom
e light switch position,
when you press the lens, the light on the sidethat is pressed illuminates; when you press the lens again, the light goes off.
N00525400459
The rear dome light can be turned on by slid- ing the dome light switch.
 If the dome light is left switched on with the electric motor switch in the “LOCK” or “ACC” position and adoor or the liftgate is opened, it goes off automatically after approxi- mately 30 minutes.The light will illuminate again after it automatically goes off in the fol- lowing cases:• When the electric motor switch is turned to the “ON” position. • When the keyless entry system remote control transmitter is oper- ated.• When any of the doors or the lift- gate is opened after all doors and the liftgate are closed.
NOTE
 When the key is removed while the doors and liftgate are closed, the dome light will illuminate for appr
oximately 30 seconds
before going off.  The time until the light goes off (delayed off) dealer for details. However, the dome light
will shut off in sync
with the automatic relocking function, even if the dome light delayed off function has been extended. For the automatic relockingfunction, refer to “K
eyless entry system” on
page 5-5.
 The auto cut-out function can be deactivated. See a certified i-MiEV dealer for details.2- The dome light goes off.
Reading lights

Dome light (Rear)
NOTE
1- On2- Door 3- Off 1- (ON) The dome light comes on.2- (
)
BK0220401US.book 78 ページ ２０１５年６月３日　水曜日　午前７時４２分

Safe driving techniques 6-4 Driving safety
6
 Move the driver’s seat as far backward as possible, while still
keeping good visibil-
ity, and good control of the steering wheel, brakes, accele
rator, and controls.
Check the instrument panel indicators forany possible problem.  Move the front passe
nger seat as far back
as possible.  Make sure that infa
nts and small children
are properly restrained in accordance with all laws and regulations.
Check these by selecti
ng the defroster mode,
and set the blower swit
ch on high. You should
be able to feel the air blowing against the windshield. (Refer to “Defrosting or defogging the wind- shield and door windows” on page 7-9.) Check all the tires for heavy tread wear or uneven wear patterns.
Look for stones, nails,
glass, or other objects
stuck in the tread. Look
for any tread cuts or sidewall cracks. Check the wheel nuts for tightness, and the tires for proper pressures. Replace your tires beforethey are heavily worn out.
As your vehicle is equi
pped with a tire pres-
sure monitoring system, there is a risk ofdamage to the tire inflation pressure sensors when the tire is replaced on the rim. Tire replacement should, th
erefore, be performed
only by a certified i-MiEV dealer. Have someone watch while you turn all the exterior lights on and off. Also check the turn signal indicators and
high-beam indicators on
the instrument panel. Check the ground under the vehicle after parking overnight, for wa
ter, oil, or other
leaks. Make sure all the fluid levels are cor- rect.
N00629200124
Even this vehicle’s safety equipment, andyour safest driving, cannot guarantee that youcan avoid an accident or injury. However, if you give extra attention to the following areas, you can better protect yourself andyour passengers:
 Drive defensively. Be aware of traffic, road and weather conditions. Leave plentyof stopping distance between your vehicle and the vehicle ahead.  Before changing lanes, check your mir- rors and use your turn signal light.  While driving, watch the behavior of other drivers, bicyc
lists, and pedestrians.
 Always obey applicable
laws and regula-
tions. Be a polite and alert driver. Always leave room for unexpected events, such as sudden braking.
N00629400416
 Check the 12V starter battery, including terminals and cables. During extremely cold weather, the 12V starter battery willnot be as strong and
its power level may
drop. Before driving the vehicle, check to see ifthe headlights are as bright as normal. Charge or replace the 12V starter battery if necessary. During extreme coldweather, it is possibl
e that a very low 12V
starter battery could freeze.
Defrosters Tires
Lights Fluid leaks Safe driving techniques
Driving during cold weather
BK0220401US.book 4 ページ ２０１５年６月３日　水曜日　午前７時４２分

If the vehicle breaks down 8-2 For emergencies
8
N00836301243
If your vehicle breaks down on the road, move to the shoulder and turn on the hazard warning flashers. If there is no shoulder, orthe shoulder is not safe, drive in the right lane slowly, with the hazard lights flashing, until you come to a safe stopping place. Keep theflashers flashing. If the ready indicator light goes out while driving, the brakes a
nd steering will continue
to work, but without power assist, so more effort will be required
for braking and steer-
ing. Stop the vehicle on the shoulder of the road and turn on the hazard warning flashers. If you need to push your vehicle, turn theelectric motor switch to the “ON” position, and place the selector lever in the “N” (NEU- TRAL) position.
N00836400742
If the electric motor unit cannot be energizedbecause the 12V starter battery is weak ordead, you can start it with the battery from another vehicle using jumper cables.
1. Take off any metal jewelry such as watch bands or bracelets
that might make an
accidental electrical contact. 2. Position the vehi
cles close enough
together so that the jumper cables can reach, but be sure the vehicles are nottouching each other.
3. Set the parking brake firmly on your vehi- cle and move the selector lever into the “P” (PARK) position. 4. Set the parking brake firmly on the othervehicle. Put the automatic transaxle in “P”5. Turn the ignition switch (the electric motor switch) on each vehicle to the “LOCK” position. 6. Remove the battery
cover, and then make
sure your 12V starter
battery electrolyte is
at the proper level. (Refer to “Checking 12V starter battery electrolyte level” onpage 9-8.)
If the vehicle breaks down Jump-starting
WA R N I N G To reduce the risk of igniting flammable gas that may be em
itted from the 12V
starter battery, carefully read this sectionbefore jump-starting the vehicle. Do not try to start the electric motor unit by pushing or towing the vehicle. This can cause an accident re
sulting in serious
injury or death and
can damage the vehi-
cle.CAUTION Do not attempt jump st
arting the 12V starter
battery while the main
drive lithium-ion bat-
tery is being charged. Doing so could dam-age the vehicle or charging equipment.NOTE
 Do not use jumper cables if they have dam- age or corrosion.
CAUTION Check the other vehicle.
It must have a 12V
battery. If the other system is not 12V, bothsystems can be damaged.NOTE
 Turn off all lights, heat
er, and othe
r electrical
loads. This will
help avoid sparks.
BK0220401US.book 2 ページ ２０１５年６月３日　水曜日　午前７時４２分

Fuses
Vehicle care and maintenance 9-19
9
Under the hood, the fuse
block is located as
shown in the illustration. Press the tab (A) and remove the cover.
N00954801313
This fuse list shows the names of the electri-cal systems and their fuse capacities. Always replace a blown fuse with one of thesame capacity as the original.
Under the hood
Fuse load capacities Passenger compartment fuse loca- tion table
No.
Sym- bol
Electrical system
Capac-ity
1 Tail light (left) 7.5 A 2
Cigarette lighter/ 12 V power outlet
15 A
3 — — — 4 Starter 7.5 A 5 Audio amplifier 20 A 6— — — 7 Tail light (right) 7.5 A 8
Outside rearview mirrors
7.5 A
9
Control unit (Electric motor unit)
7.5 A
10 Control unit 7.5 A 11 Rear fog light 10 A12 Door lock 15 A 13
Interior lights (Dome lights)
10 A
14 Rear window wiper 15 A 15 Gauges 7.5 A 16 Relay 7.5 A 17 Heated seat 20 A
BK0220401US.book 19 ページ ２０１５年６月３日　水曜日　午前７時４２分

Fuses 9-20 Vehicle care and maintenance
9
* : Fusible link  Some fuses may not be installed on your vehicle, depending on the vehicle model or specifications. The table above shows the main equip- ment corresponding to each fuse.
* : Fusible link
18 Option 10 A 19
Heated outside rear- view mirrors
7.5 A
20 Windshield wiper 20 A 21 Back-up lights 7.5 A 22 Defogger 30 A23 Heater 30 A24 12V starter battery 30 A
*
25 Radio 10 A 26
Electronic con- trolled unit
15 A
27 —
trolled unit
7.5 A
No.
Sym- bol
Electrical system
Capac-ity
Under the hood fuse location table No.
Sym- bol
Electrical system
Capac-ity
1— — — 2 12V starter battery 30 A
*
3
Electric motor
switch
40 A
*
4 Radiator fan motor 40 A
*
5
Power window con-
trol
40 A
*
6
Brake electric vac-
uum pump
30 A
*
7
Electric motor unit
control
15 A
8
Stop lights (Brake
lights)
15 A
9 Front fog lights 15 A 10
Water pump (Electric motor
unit)
15 A
11 Charge 10 A 12
Hazard warning
flasher
10 A
13 Horn 10 A 14
Daytime running
lights
10 A
15
Main drive lithium- ion battery fan
motor
15 A
16
Water pump
(Air conditioning)
10 A
17
Headlight (low beam) (right)
20 A
18
Headlight (low beam) (left)
20 A
19
Headlight (high beam) (right)
10 A
20
Headlight (high beam) (left)
10 A
No.
Sym- bol
Electrical system
Capac-ity
BK0220401US.book 20 ページ ２０１５年６月３日　水曜日　午前７時４２分

Replacement of light bulbs
Vehicle care and maintenance 9-23
9
N00950400617 N00943200349
The alignment of th
e headlights should be
checked by a certified i-MiEV dealer.
N00915501184
1. Insert a flat blade sc
rewdriver into the end
of the light nearer the rear of the body and pry gently to remove the light.
2. Remove the socket and bulb assembly together by turning it counterclockwise. 3. Pull the bulb out of the socket.
Description
Wattage
ANSI Tr a d e N o . or Bulb type
8- High-mounted
stop light
5 W W5W
9- Tail and stop
light
——
10- Rear turn sig-
nal light
21 W WY21W
11- Back-up light 21 W W21W 12- License plate
light
5 W W5W
13- Rear side-
marker light
5 W W5W
14- Regular charge
port light
——
NOTE
 The tail and stop lights along with the regu- lar charge port light use LEDs rather thanbulbs. For repair and replacem
ent, contact a certi-
fied i-MiEV dealer.
Inside
Description
Wattage
1- Dome light (Rear) 8 W 2- Dome light
(Front)/Reading lights
8 W
Adjustment of
headlight aim
Front side-marker lights
* : Front of the vehicleNOTE
Wrap a cloth around the tip of the screw- driver to keep from scratching the lens.
*
BK0220401US.book 23 ページ ２０１５年６月３日　水曜日　午前７時４２分