2017 MERCEDES-BENZ SLC keyless

Problem
Possible causes/consequences and P Solutions
The engine cannot be
started using the Smart-
Key. The on-board voltage is too low. X
Switch off non-essential consumers, e.g. seat heating or interior
lighting, and try to start the engine again.
If this does not work: X
Check the starter battery and charge it if necessary ( Y
page 248).
or X
Jump-start the vehicle ( Y
page 249).
or X
Consult aq ualified specialist workshop.
The engine cannot be
started using KEYLESS-
GO. The SmartKey is in
the vehicle. The vehicle is locked. X
Unlock the vehicle and try to start the vehicle again.
The SmartKey battery is discharged or nearly discharged. X
Check the SmartKey battery ( Y
page 66) and replace it if necessary
( Y
page 66).
If this does not work: X
Start your vehicle with the SmartKey in the ignition lock.
There is interference from ap owerful source of radio waves.X
Start your vehicle with the SmartKey in the ignition lock.
You have lost aS mart-
Key. X
Have the SmartKey deactivated at aq ualified specialist workshop.X
Report the loss immediately to the vehicle insurers. X
If necessary, have the locks changed as well.
You have lost the
mechanical key. X
Report the loss immediately to the vehicle insurers. X
If necessary, have the locks changed as well.
Doors
Important safety notes
G WARNING
If children are left unsupervised in the vehicle,
they could: R
open the doors, thus endangering other
people or road users. R
get out and disrupt traffic. R
operate the vehicle's equipment. Additionally, children could set the vehicle in
motion if, for example, they: R
release the parking brake. R
shifting the automatic transmission out of
park position P R
Start the engine.
There is ar isk of an accident and injury.
When leaving the vehicle, always take the
SmartKey with you and lock the vehicle. Never
leave children or animals unattended in the
vehicle. Always keep the SmartKey out of
reach of children.68
Doors
Opening and closing

Unlocking and opening doors from
the inside
! The side windows will not open/close if the
battery is discharged or if the side windows
have iced up. It will then not be possible to
close the door. Do not attempt to forc et he
door closed. You could otherwise damage the
door or the side window.
You can open ad oor from inside the vehicle
even if it has been locked.
If the vehicle has previously been locked from
the outside, openin gad oor from the inside will
trigger the anti-theft alarm system .S witc ho ff
the alarm ( Y
page 61).
X
Pull door handle D .
If the door is locked, locking knob C pops up.
The door is unlocked and can be opened.
When ad oor is opened, the side window on that
side opens slightly. When the door is closed, the
side window closes again.
Centrally locking and unlocking the
vehicle from the inside You can centrally lock or unlock the vehicle from
the inside. For example, you can unlock the
front-passenge rd oor from the inside or lock the
vehicle before you pull away. X
To unlock: press button C .X
To lock: press button D .
If the front-passenge rd oor is closed, the vehi-
cle locks.
The central locking button does not lock or
unlock the fuel filler flap or the stowage com-
partment in the center console.
You cannot unlock the vehicle centrally from the
inside if the vehicle has been locked with the
SmartKey or KEYLESS-GO.
You can open ad oor from inside the vehicle
even if it has been locked.
If al ocked door is opened from the inside, the
previous unlock status of the vehicle will be
taken int oc onsideratio ni f:R
the vehicle was locked using the locking but-
ton for the central locking, or R
if the vehicle was locked automatically
The vehicle will be fully unlocked if it had previ-
ously been fully unlocked. If only the driver's
door had been previously unlocked, only the
door which has been opened from the inside is
unlocked.
Automatic locking feature Doors 69
Opening and closing Z

Opening/closing from outside
Opening X
Press the 6 button on the SmartKey.X
Pull handle C .X
Raise the trun kl id.
Closing
X
Pull the trun kl id down using recess C .X
Lock the vehicle if necessary using the 7
button on the key or with KEYLESS-GO.
If KEYLESS-GO detects aS martKey in the trunk,
it does not lock.
Locking the trunk separately You can lock the trun ks eparately. If you then
unlock the vehicle centrally, the trun kr emains
locked and cannot be opened. X
Close the trun kl id.X
Take the mechanical key out of the SmartKey
( Y
page 65). X
Inser tt he mechanical key into the trun kl id
lock as far as it will go. X
Turn the mechanical key clockwise from posi-
tion G to position H .X
Remove the mechanical key. X
Inser tt he mechanical key into the SmartKey.
Unlocking the trunk (mechanical key)
! The trun kl id swings upwards when opened.
Therefore, make sure that there is sufficient
clearanc ea bove the trun kl id.
If the trun kc annot be unlocked with the Smart-
Key or KEYLESS-GO, use the mechanical key.
If you use the mechanical key to unlock and
open the trun kl id, the anti-thef ta larm system
will be triggered. Switc ho ff the alarm
( Y
page 61). X
Take the mechanical key out of the SmartKey
( Y
page 65). X
Inser tt he mechanical key into the trun kl id
lock as far as it will go.
X
Turn the mechanical key from position G
counter-clockwise as far as it will go to posi- Trunk 71
Opening and closing Z

Convenience closing with KEYLESS-GO
G WARNING
When usin gt he convenience closin gf eature,
part soft he body coul dbet ra pped in th ec los-
ing area when as ide window is bein gc losed.
Ther eisar is kofi njury.
Observ et he complet ec losin gp rocedure
when th ec onvenience closin gf eature is oper-
ating. Mak es ure that no body part sa re in
close proximity durin gt he closin gp rocedure.
Procee dasf ollows if someon eist ra pped:X
Release th er ecessed sensor surface on the
door handle. X
Immediately pull and hold th ed oor handle
and keep th ed oor handle pulled.
The side windows open.
Wit hK EY LESS-GO you can close all side win-
dows simultaneously. The KEYLESS-GO key
must be outside th ev ehicle .A ll th ed oor sm ust
be closed.
X
Touc hr ecessed sensor surface C on the
door handle until th es ide windows are fully
closed.
i Mak es ure you only touch recessed sensor
surface C .X
To interrup tc onvenience closing: release
recessed sensor surface C on th ed oor han-
dle.
Resetting th es id ew indows
If as ide window can no longer be closed fully,
you must reset it. X
Close all th ed oors. X
Turn th eS ma rtKey to position 1 or 2 in the
ignition lock. X
Pull th ec orrespondin gs witch on th ed oor
control panel until th es ide window is com-
pletely closed ( Y
page 73).X
Hol dt he switch for an additional second.
If th es ide window open sa gain slightly:X
Immediately pull th ec orrespondin gs witch on
th ed oor control panel until th es ide window is
completely closed ( Y
page 73).X
Hol dt he switch for an additional second.
If th er espectiv es ide window remains closed
after th eb utto nisr eleased, then it has been
set correctly. If this is no tt he case, repeat the
steps above.74
Sid ew indows
Opening and closing

Opening/closing using the SmartKey
Important safet yn otes
G WARNING
When opening or closing the roof, body parts
could be trapped by, for example, the roof
mechanism, trun kl id or side windows. There
is ar isk of injury.
When raising or lowering the roof, make sure
that no body parts are in the vicinity of moving
components. If someon eb ecomes trapped,
release the button.
Opening and closing This function is only available on vehicles with
KEYLESS-GO or with roof comfort operation. X
Close the trun kl id ( Y
page 70).X
Vehicles with comfort operation: point the
tip of the SmartKey at the driver's door han-
dle. X
Vehicles with KEYLESS-GO: the SmartKey
must be within 6ft(2m )o ft he vehicle.X
To open: press and hold the 6 button on
the SmartKey until the roof is fully opened.
The roof and the rear side windows open. The
fron ts ide windows close.X
To interrupt the opening procedure:
release the 6 button.X
To open the front side windows: press the
6 button on the SmartKey again.X
To close: press and hold the 7 button on
the SmartKey until the roof is fully closed.
The roof and the side windows close. X
To interrupt the closing procedure: release
the 7 button.
Locking the roof again
Important safet yn otes
G WARNING
If you do not fully open/close the soft top, the
soft-top hydraulics depressuriz ea fter as hort
time. This causes the soft top to lower unex-
pectedly and may cause you or other stob e
trapped. There is ar isk of injury. Always open or close the soft top completely.
The roof is not locked if: R
the Y symbol and the Vario-Roof in
Operation message appear in the multifunc-
tion display R
the Y symbol and the Open/Close
Vario-Roof Completely message appear in
the multifunction display and you hear aw arn-
ing tone R
you hear aw arning ton ef or up to ten seconds
when pulling away or while driving
Locking You can lock the roof again if it is not locked
fully. X
Pull over and stop the vehicle safely as soon
as possible, paying attention to road and traf-
fic conditions. X
Make sure that the SmartKey is in position 2
in the ignition lock. X
Press the roof switch ( Y
page 76).
Trunk partition
General notes
! To avoid damaging the roof or luggage when
folding back the roof, you should: R
only load the trun ktob elow the trun kp ar-
tition R
not place any objects on or in fron toft he
trun kp artition R
not place any objects on the cover behind
the roll bars R
not allow the cargo to push the trun kp ar-
tition upwards
The trun kp artition can be used to cover luggage
and loads in the trunk. Roof 77
Opening and closing Z

Position of the steering wheel when the
EASY-ENTRY/EXIT featur eisa ctiveThe steering wheel swings upwards when you: R
remove the SmartKey from the ignition lock R
open the driver's door with KEYLESS-GO in
position 1R
open the driver's door and the SmartKey is in
position 0 or 1 in the ignition lock
i The steering wheel only moves upwards if it
has not already reached the upper end stop.
Position of the steering wheel for driv-
ing The steering wheel is moved to the last selected
position when: R
the driver's door is closed R
you insert the SmartKey into the ignition lock
or R
you press the Start/Stop button once on vehi-
cles with KEYLESS-GO
When you close the driver's door with the igni-
tion switched on, the steering wheel is also
automatically moved to the previously set posi-
tion.
The last position of the steering wheel is stored
when you switch off the ignition or when you
store the settin gw ith the memory function
( Y
page 91).
Crash-responsive EASY-EXIT feature If the crash-responsive EASY-EXIT feature is trig-
gered in an accident, the steering column will
move upwards when the driver's door is opened.
This occurs irrespective of the position of the
SmartKey in the ignition lock. This makes it eas-
ier to exit the vehicle and rescue the occupants.
The crash-responsive EASY-EXIT feature is only
operational if the EASY-EXIT/ENTRY feature is
activated in the on-board computer
( Y
page 174). Mirrors
Rear-view mirror X
Anti-glare mode: flick anti-glare lever C for-
wards or back.
Exterior mirrors
Adjusting the exterior mirrors
G WARNING
You could lose control of your vehicle if you do
the following while driving: R
adjust the driver's seat, head restraint,
steering wheel or mirrors R
fasten the seat belt
There is ar isk of an accident.
Adjust the driver's seat, head restraint ,s teer-
ing wheel and mirror and fasten your seat belt
before startin gt he engine.
G WARNING
The exterior mirror on the front-passenger
side reduces the size of the image. Visible
object sa re actually closer than they appear.
This means that you could misjudge the dis-
tance from road users traveling behind, e.g.
when changing lane. There is ar isk of an acci-
dent.
For this reason, always make sure of the
actual distance from the road users traveling
behind by glancing over your shoulder.88
Mirrors
Seats, steering whee la nd mirrors

Where possible, avoid spinnin gt he drive
wheels when pulling away on slippery roads.
You could otherwise damage the drive train.
SmartKey positions
SmartKey
Z
To remove the SmartKeyG
Power supply for some consumers, such as
the windshield wipersH
Ignition (power supply for all consumers)
and drive positionI
To start the engine
i The SmartKey can be turned in the ignition
lock even if it is not the correct SmartKey for
the vehicle. The ignition is not switched on.
The engine cannot be started.
KEYLESS-GO
General notes Vehicles with KEYLESS-GO are equipped with a
SmartKey featuring an integrated KEYLESS-GO
start function and ad etachable Start/Stop but-
ton.
The Start/Stop button must be inserted in the
ignition lock and the SmartKey must be in the
vehicle.
When you insert the Start/Stop button into the
ignition lock, the system needs approximately
two seconds recognition time. You can then use
the Start/Stop button.
Pressing the Start/Stop button several times in
succession corresponds to the differen tk ey
positions in the ignition lock. This is only the
case if you are not depressing the brake pedal. If you depress the brake pedal and press the
Start/Stop button ,t he engine start si mmedi-
ately.
Ac heck which periodically establishes ar adio
connection between the vehicle and the Smart-
Key determines whether av alid SmartKey is in
the vehicle. This occurs ,f or example, when
starting the engine.
To start the vehicle without actively using the
SmartKey: R
the Start/Stop button must be inserted in the
ignition lock. R
the SmartKey must be in the vehicle. R
the vehicle must not be locked with the
SmartKey or KEYLESS-GO ( Y
page 63).
Do not keep the SmartKey: R
with electronic devices, e.g. am obile phone
or another SmartKey. R
with metallic objects, e.g. coins or metal foil. R
inside metallic objects, e.g. am etal case.
This can impair the functionality of the KEY-
LESS-GO key.
If you lock the vehicle with the SmartKey's
remot ec ontrol or with KEYLESS-GO, after a
short time: R
you will not be able to switch on the ignition
with the Start/Stop button. R
you will not be able to start the engine with the
Start/Stop button until the vehicle is
unlocked again.
The engine can be switched off while the vehicle
is in motion by pressing and holding the Start/
Stop button for three seconds. This function
operates independently of the ECO start/stop
automatic engine switch-off function.
Key positions with KEYLESS-GO
C
Start/Stop button
D
Ignition lock Driving 115
Driving and parking Z

reach its operating temperature. The sound of
the engine may change during this time.
Automatic transmission X
Depress the brake peda la nd keep it
depressed. X
Shift the transmission to position P .
Transmission position display P is shown in
the multifunction display.
i You can start the engine in transmission
position P and N .
Starting procedure with the SmartKey To start the engine using the SmartKey instead
of KEYLESS-GO, pul lt he Start/Stop button out
of the ignitio nl ock.X
Turn the SmartKey to position 3 in the ignition
lock ( Y
pag e1 15) and release it as soon as the
engine is running.
Usin gK EYLE SS-GO to start the engineThe Start/Stop button can be used to start the
vehicl em anually withou ti nserting the SmartKey
into the ignitio nl ock. The Start/Stop button
must be inserted in the ignitio nl ock and the
SmartKey must be in the vehicle. This mode for
starting the engine operates independently of
the ECO start/stop automatic engine start func-
tion. X
Depress the brake peda la nd keep it
depressed. X
Press the Start/Stop button once
( Y
pag e1 15).
The engine starts.
Pulling away
General notes
G WARNING
If the engine spee disa bove the idling speed
and you engage transmission position D or R ,
the vehicl ec ould pul la wa ys uddenly .T here is
ar isk of an accident.
When engaging transmission position D or R ,
alway sf irmly depress the brake peda la nd do
not simultaneously accelerate. ! Change gea ring ood time and avoi ds pin-
ning the wheels. You could otherwise damage
the vehicle.
Depress the accelerator carefully when pulling
away.
The vehicl el ocks centrally once you have pulled
away. The locking knobs in the doors drop down.
You can open the doors from the insid eata ny
time.
You can als od eactivate the automatic locking
feature ( Y
pag e1 73).
It is only possible to shift the transmission from
position P to the desired position if you depress
the brake pedal. Only then is the shift lock
released.
i Upshifts take place at highe re ngine speeds
after ac old start. This help st he catalytic con-
verter to reach its operating temperature
more quickly.
Information on the automatic release of the
electric parking brake ( Y
pag e1 33).
Hill start assist Hill start assist help sy ou when pulling awa yf or-
ward sorinr everse on an uphill gradient. It holds
the vehicl ef or as hort time after you have
removed you rf oot from the brake pedal. This
gives you enoug ht ime to move you rf oot from
the brake peda ltot he accelerator peda la nd to
depress it before the vehicl eb egins to roll.
G WARNING
After as hort time, hill start assist wil lnol on-
ger brake you rv ehicl ea nd it could roll away.
There is ar isk of an accident and injury.
Therefore, quickly move you rf oot from the
brake peda ltot he accelerator pedal. Never
leave the vehicl ew hen it is held by hill start
assist.
Hill start assist is not active if: R
you are pulling awa yonal evel road or on a
downhill gradient. R
the transmission is in position N .R
the electric parking brake is applied. R
ESP ®
is malfunctioning. Driving 117
Driving and parking Z