2017 MERCEDES-BENZ SLC-Class coolant level

ProblemPossible causes/consequences andMSolutions
The coolant temperature
gauge showsavalue
above 248 ‡(120 †).
The coolant warning
lamp may also be on and
aw arning tone may
sound.The coolant level is too low. The coolant is too hot and the engine is no
longer being cooled sufficiently.
XStop as soon as possible and allow the engine and the coolant to
cool down.
XCheck the coolant level (Ypage 233). Observe the warning notes
as you do so and add coolant if necessary.
If the coolant level is correct,t he engine radiator fan may be faulty. The
coolant is too hot and the engine is no longer being cooled sufficiently.
XAt coolant temperatures below 248 ‡(120 †), drive to the nearest
qualified specialist workshop.
XAvoid heavy loads on the engine as you do so, e.g. driving in moun-
tainou sterrai nand stop-and-go traffic.
DYNAMIC SELEC Tbutton
Use the DYNAMIC SELECT button to change the
drive program. Depending on the drive program selected the following vehicle characteristics
wil lchange:
Rthe drive (engine and transmission manage-
ment)
Rthe suspension( vehicles with adaptive
adjustabl edamping or AMG sports suspen-
sion)
Rthe steering
Rthe availability of the ECO start/stop function
Each time you start the engine with the Smart-
Key or the Start/Stop button, drive program Cis
activated. For further information about starting
the engine, see (
Ypag e116).
XPress DYNAMIC SELECT button :as many
times as necessary until the desired drive
programiss elected.
The selected drive programa ppears in the
multifunction display. After ashort time the displayg
oes out and the status icon of the
selected drive programa ppears.
In addition, the current drive programs ettings
are displayed briefly in the multimedi asystem
display.
iIn af ew countries, the ECO start/stop func-
tion is deactivated at the factory due to the
available fuel grade. In this case, the ECO
start/stop function is not available in any
drive program, regardless of the displayint he
multimedi asystem display.
Availabl edrive programs:
CComfortComfortabl eand economi-
cal driving characteristics
S SportSporty driving characteris-
tics
S+ Sport PlusParticularly sporty driving
characteristics
IIndividualIndividua lsettings
EEconomyParticularly economical
driving characteristics
Additional information for drive programs
(Ypag e125).
DYNAMICS ELECTbutton121
Driving and parking
Z

Coolanttemperatur egauge
GWARNING
Opening th ehood when th eengineiso ver-
heated or when there is afireint heengine
compartmen tcoul de xpose you to hot gases
or other servic eproducts. Thereisar isko f
injury.
Let an overheate denginec ooldown before
opening th ehood.Ift here is afireint he
enginec ompartment, keep th ehood closed
and contac tthe fired epartment.
!Ad isplay message is shown if th ecoolant
temperatur eistoohigh.
If th ecoolant temperatur eisover2 48 ‡
(12 0† ), do no tcontinue driving .The engine
will otherwise be damaged.
The coolant temperatur egage is in th einstru-
men tcluste ront heright-hands ide (
Ypage 31).
The Hmarkin ginthecoolant temperatur egauge
corresponds to acoolant temperatur eof
approximately 24 8‡(120† ).
Under normal operatin gconditionsa nd at the
correc tcoolant level, th ecoolant temperature
gauge may ris etotheHmarking.
Operatin gthe on-boar dcomputer
Overview
:Multifunction display
;Right control panel
=Leftc ontrol panel
XTo activate th eon-boar dcomputer: turn
th eS ma rtKey to position 1in th eignition lock.
You can control th emultifunction display and
th es ettings in th eon-board computer usingt he
buttons on th emultifunction steering wheel.
Left control panel
=
;RCalls up th emenua nd men ubar
9
:Press briefly:
RScroll sinlists
RSelect sasubmenuorf unction
RIn theAudiomenu: select sthe
previous or next station, when the
preset list or statio nlist is active,
or an audio track or vide oscene
RIn the Tel(telephone )menu:
switches to th ephoneb ook and
selects anam eort elephone num-
ber
164Displays and operation
On-boardc omputer and displays

Engine
Display messagesPossible causes/consequences andMSolutions
?
CheckCoolantLevelSee Operator'sMan‐ual
The coolant levelistoolow.
!Avoid making longj ourneys with to olittle coolant in th eengine
cooling system. The engine will otherwise be damaged.
XAdd coolant ,observing th ewarning note sbefore doings o
(Ypage 233).
XIf you nee dtoadd coolant mor eoften than usual, have th eengine
coolant system checked at aqualified specialist workshop.
?The fan motor is faulty.
XIf th ecoolant temperatur egauge is below the Hmarking
(Ypage 164), driv eontothenex tqualified specialist workshop.
XAvoid heavyl oads on theengine as you do so, e.g .driving in moun-
tainous terrain and stop-and-go traffic.
?
CoolantT oo HotStopVehicleT urnEngine Off
The coolant is to ohot.
Aw arning tone also sounds.
GWARNING
Do no tdrivew hen your engine is overheated. This can caus esome
fluids whichm ay have leaked int othe engine compartmen ttocatch
fire.
Steam from th eoverheate dengine can also caus eserious burn swhich
can occur jus tbyopening th ehood.
Thereisar isk of injury.
XPull overand stop th evehicle safely and switch off th eengine ,pay-
ing attention to road and traffic conditions.
XSecure th evehicle against rolling away (Ypage 131).
XLeavet hevehicle and keep asafe distanc efromt hevehicle until the
engine has cooled down.
XMakes ure that th eair supply to th eengine radiator is no tblocked,
e.g .bys now, slush or ice.
XDo no tstart th eengine again until th edisplay message goes out and
th ec oolant temperatur egauge is below the Hmarking
(
Ypage 164). Otherwise, th eengine coul dbedamaged.
XPay attention to th ecoolant temperatur egauge, observing the
warning note s(Ypage 233).
XIf thetem peratur eincreases again,v isitaq ualified specialist work-
shop immediately.
Under normal operatin gconditionsa nd at thecorrec tcoolant level,
th ec oolant temperatur egauge may rise to the Hmarking
(
Ypage 164).
190Displa ymessages
On-boardc omputer and displays

GWARNING
If engine oil comes into contact with hot com- ponents in the engine compartment, it may
ignite. There is arisk of fire and injury.
Make sure that engine oil is not spilled next to
the filler neck. Let the engine cool downa nd
thoroughly clea nthe engine oil off the com-
ponents before starting the engine.
HEnvironmental note
When adding oil,t ake care not to spil lany. If
oil enters the soil or waterways, it is harmfu lto
the environment.
!Only use engine oilsa nd oil filters that have
been approved for vehicles with aservice sys-
tem. You can obtai nalist of the engine oils
and oil filters tested and approved in accord- ance with the Mercedes-Benz Specifications
for Service Products at any Mercedes-Benz
Service center.
Damag etothe engine or exhaust system is
caused by the following:
Rusing engine oilsa nd oil filters that have not
been specifically approved for the service
system
Rreplacing engine oil and oil filters after the
interval for replacement specified by the
service system has been exceeded
Rusing engine oil additives.
!Do not add too much oil.Ift he oil levelis
above the "max" mark on the dipstick, too
much oil has been added. This can lea dto
damage to the engine or the catalytic con-
verter. Have excess oil siphoned off.
Example :engine oil cap
XTurn cap :counter-clockwise and remove it.
XAdd engine oil.
If the oil leve lisatorbelow the MIN mark on
the oil dipstick, add 1.1 US qt (1.0 liter) of
engine oil.
XReplace cap :on the filler neck and turn
clockwise.
Ensure that the cap locks into place securely.
XCheck the oil leve lagain with the oil dipstick
(Ypag e232).
Further information on engine oil (
Ypag e286).
Checkin gand adding other service
products
Checkin gcoolantl evel
GWARNING
Certain components in the engine compart-
ment, such as the engine, radiator and parts
of the exhaust system, can become very hot.
Working in the engine compartment poses a
risk of injury.
Where possible,l et the engine cool downa nd
touch only the components described in the
following.
GWARNING
The cooling system is pressurized, particularly
when the motor is warm .Ifyou open the cap,
you coul dbescalded if hot coolant sprays out.
There is arisk of injury.
Let the engine cool downb efore you open the
cap. Wearg lovesand eye protection. Slowly
open the cap to relieve pressure.
Example
Engine compartment233
Maintenance and care
Z

XPark the vehicle onalevel surface.
Only check the coolant level when the vehicle is on alevel surface and the engine has cooled
down.
XTurn the SmartKey to position 2in the ignition
lock (Ypage 115).
On vehicles with KEYLESS-GO, press the
Start/Stop button twice (
Ypage 115).
XCheck the coolant temperature gauge in the
multifunction display.
The coolant temperature must be below
158 ‡(70 †).
XTurn the SmartKey to position 0(Ypage 115)
in the ignition lock.
XSlowly turn cap ;half aturn counter-clock-
wise to allow excess pressure to escape.
XTurn cap ;further counter-clockwise and
remove it.
If the coolant is at the level of marker bar =
in the filler neck when cold, there is enough
coolant in coolant expansion tank :.
If the coolant level is approximately 0.6 in
(1.5 cm) above marker bar =in the fuel filler
neck when warm, there is enough coolant in
expansion tank :.
XIf necessary, add coolant that has been tested
and approved by Mercedes-Benz.
XReplace cap;and turn it clockwise as far as
it will go.
For further information on coolant ,see
(
Ypage 287).
Windshield washer system
GWARNING
Certain components in the engine compart-
ment ,such as the engine, radiator and parts
of the exhaust system, can become very hot.
Workin ginthe engine compartment poses a
risk of injury.
Where possible, let the engine cool down and touch only the components described in the
following.
GWARNING
Windshield washer concentrate could ignite if it comes into contact with hot engine compo-
nentsort he exhaust system. There is arisk of
fire and injury.
Make sure that no windshield washer con-
centrate is spilled next to the filler neck.
Example
XTo open: pull cap:upwards by the tab.
XAdd the premixed washer fluid.
XTo close: press cap :ontothe filler neck
until it engages.
If the washer fluid level drops below the recom-
mended minimum fluid level of 1USgal (1 liter),
am essage appears in the multifunction display
promptin gyou to add washer fluid (
Ypage 201).
Further information on windshield washer fluid/
antifreeze (
Ypage 288).
Overview of the engine compartment
Example: gasoline engine
:
Engine oil cap
;Oil dipstick
=Brake fluid reservoir
?Washer fluid reservoir
ACoolant expansion tank
234Overview of the engine compartment
Maintenance and care

from the data shownhere. You can find the
data applicable to you rvehicleont he vehicle
identificatio nplate.
Vehicle identification number (VIN)
XSlid ethe front-passenger seattoi ts front
most position.
XFold paneling :upwards.
VIN ;can be seen.
The VIN can als obefound in the following loca-
tions:
Ron the vehicl eidentificatio nplate
(Ypag e283)
Ron the lower edge of the windshield
(Ypag e284)
Engine number
:Emissio ncontrol information plate, includ-
ing the certification of both federala nd Cali-
fornia nemissions standards
;Engine numbe r(stamped into the crank-
case)
=VIN (on the lower edge of the windshield)
Service products and filling capaci-
ties
Important safety notes
GWARNING
Service products may be poisonousa nd haz-
ardous to health. There is arisk of injury.
Comply with instructions on the use ,storage
and disposal of service products on the labels
of the respective original containers. Always
store service products sealed in their original
containers. Always keep service products out
of the reach of children.
HEnvironmental note
Dispos eofservice products in an environ-
mentall yresponsiblem anner.
Service products include the following:
RFuels
RLubricants (e.g. engine oil ,transmission oil)
RCoolant
RBrake fluid
RWindshiel dwasher fluid
RClimate control syste mrefrigerant
Comply with all vali dregulations with respect to
handling, storing, and disposing of service flu-
ids.
Components and service products must match.
You should therefore only use products that
have been tested and approved by Mercedes-
Benz.
Informatio nabout tested and approved prod-
ucts can be obtained from an authorized
Mercedes-Benz Center or on the Internet at
http://bevo.mercedes-benz.com.
You can identify service products approved by
Mercedes-Benz by the following inscriptions on
the container:
RMB-Freigabe (e.g. MB-Freigabe 229.51)
RMB-Approval( e.g. MB-Approval2 29.51)
Other designations or recommendations indi-
cate alevelofq uality or aspecificatio nin
accordance with an MB Sheet Number (e.g. MB
229.51). They have not necessarily been
approved by Mercedes-Benz.
284Service products and filling capacities
Technical data

The antifreeze/corrosion inhibitor concentra-
tion in the engine cooling system should:
Rbe at least 50%. This will protectthe engine
cooling system against freezin gdown to
approximately -35 ‡(-37 †).
Rnot exceed 55% (antifreez eprotection down
to -49 ‡[-45 †]). Otherwise, heat will not be
dissipated as effectively.
If the vehicle has lost coolant, add equal
amounts of water and antifreeze/corrosion
inhibitor.
Mercedes-Benz recommends an antifreeze/
corrosion inhibitor concentrate in accordance
with MB Specifications for ServiceP roducts
310.1.
iWhen the vehicle is first delivered, it is filled
with acoolant mixture that ensures adequate
antifreeze and anti-corrosion protection.
iThe coolant is checked with every mainte-
nancei nterval at aqualified specialist work-
shop.
Fillingc apacities
Missing values were not availableatt ime of
going to print.
ModelCapacity
SLC 300Approx.8 .5 US qt
(8.0 l)
Mercedes ‑Benz
SLC 43 AMG
Windshield washer system
Important safety notes
GWARNING
Windshield washer concentrate could ignite if it comes into contact with hot engine compo-
nentsort he exhaust system. There is arisk of
fire and injury.
Make sure that no windshield washer con-
centrate is spilled next to the filler neck.
!Only use washer fluid that is suitable for
plastic lamp lenses, e.g. MB SummerFit or MB WinterFit. Unsuitable washer fluid could dam-
age the plastic lenses of the headlamps.
!Only MB SummerFit and MB WinterFit
washer fluid should be mixed together. The
spray nozzles may otherwise become
blocked.
Do not use distilled or de-ionised water. Other-
wise, the level sensor may give afalse reading.
When handling washer fluid, observe the impor-
tant safety notes on service products
(
Ypage 284).
At temperatures above freezing:
XFill the washer fluid reservoir with amixture of
water and windshield washer fluid, e.g. MB
SummerFit.
XAdd 1part MB SummerFit to 100 parts water.
At temperatures below freezing:
XFill the washer fluid reservoir with amixture of
water and washer fluid, e.g. MB WinterFit.
For the correctm ixing ratio refer to the infor-
mation on the antifreeze reservoir.
iAdd windshield washer fluid, e.g. MB Sum-
merFit or MB WinterFit, to the washer fluid all
year round.
Climate control system refrigerant
Important safety notes
The climate control system of your vehicle is fil-
led with refrigerant R‑ 134a.
The instruction label regarding the refrigerant
type used can be found on the radiator cross
member.
!Only the refrigerant R‑134a and the PAG oil
approved by Mercedes-Benz may be used.
The approved PAG oil may not be mixed with
any other PAG oil that is not approved for
R-134a refrigerant.O therwise, the climate
control system may be damaged.
Servicew ork, such as refilling with refrigerant or
replacing component parts, may only be carried
out by aqualified specialist workshop. All appli-
cable regulations, as well as SAE standard J639,
must be adhered to.
Always have work on the climate control system
carried out at aqualified specialist workshop.
288Service products and filling capacities
Technical data