2017 MERCEDES-BENZ SLC-Class key

Before changingafuse
XSwitch off the engine.
XSwitch off al lelectrical consumers.
XMake sure thatt he ignition is switched off
(Ypage 115).
or
XWhe nusing the SmartKey, turn the SmartKey
to position 0in the ignition lock and remove it
(
Ypage 115).
XSecure the vehicl eagain st rolling away
(Ypage 131).
All indicator lamps in the instrument cluster
must be off.
The fuses are locate dinvarious fus eboxes:
RFus eboxin the engine compartment on the
left-hand side of the vehicle, when viewe din
the direction of travel
RFus eboxin the trunk
Fuse bo xinthe engine compartment
i
Observ ethe "Important safety notes "sec-
tio n(Ypage 253).
GWARNING
Whe nthe hoo disopena nd the windshield
wipers are set in motion, yo ucan be injured by
the wipe rlinkage. There is ariskofi njury.
Alway sswitch off the windshield wipers and
the ignition before opening the hood.
XMake sure thatt he windshield wipers are
turne doff.
XOpe nthe hood.
XUse adry cloth to remove any moisture from
the fus ebox.
XTo open: open clamps ;.
XRemove fuseboxcover :forwards.
XTo close: check whethe rthe sea lislying cor-
rectl yinc over:.
XInsert cover :at the rea rofthe fus eboxinto
the retainer.
XFol dd ownc over :and close clamps ;.
XClose the hood.
Fuse boxinthe trunk
i
Observ ethe "Important safety notes "sec-
tio n(Ypage 253).
The fus eboxis locate dinthe trunk behind the
partition covering.
XOpe nthe trunk lid.
XTo open: release cover :on the right and
left-hand side swithaf lato bject.
XOpe ncover :downward sinthe direction of
the arrow.
254Fuses
Breakdo wn assis tance

same time cannot be detected by the tire pres-
sure loss warning system.
The tire pressure monitor is not able to warn you
ofas udden loss of pressure, e.g. if the tire is
penetrated by aforeign object. In the event of a
sudden loss of pressure, bring the vehicle to a
halt by braking carefully .Avoid abrupt steering
movements.
The function of the tire pressure loss warning
system is limited or delayed if:
Rsnow chains are mounted on your vehicle's
tires.
Rroad conditions are wintry.
Ryou are driving on sand or gravel.
Ryou adopt avery sporty driving style (corner-
ing at high speeds or driving with high rates of acceleration).
Ryou drive with aheavy load.
Restarting the tire pressure loss warn-
ing system
Restart the tire pressure loss warning system if
you have:
Rchanged the tire pressure
Rchanged the wheels or tires
Rmounted new wheels or tires
XBefore restarting, make sure that the tire
pressures are set properly on all four tires for
the respective operating conditions.
The recommended tire pressure can be found
on the Tire and Loading Information placard
on the B-pillar. Additionally, atire pressure
table is attached to the fuel filler flap. The tire pressure loss warning system can only give
reliable warnings if you have set the correct
tire pressure. If an incorrect tire pressure is
set, these incorrect values will be monitored.
XAlso observe the notes in the section on tire
pressures (Ypage 258).
XMake sure that the SmartKey is in position 2
in the ignition lock (Ypage 115).
XPress the =or; button on the steering
wheel to select the Serv.menu.
XPress the9or: button to select
Tire Pressure.
XPress the abutton.
The Run Flat Indicator Active Press
'OK' to Restartmessage appears in the
multifunction display. If you wish to confirm the restart:
XPress the
abutton.
The Tire Pressure Now OK?message
appears in the multifunction display.
XPress the 9or: button to select Yes.
XPress theabutton.
The Run Flat Indicator Restartedmes-
sage appears in the multifunction display.
After ateach-in period, the tire pressure loss
warning system will monitor the set tire pres- sures of all four tires.
If you wish to cancel the restart:
XPress the %button.
or
XIf the Tire Pressure Now OK?message
appears, use the 9or: button to
select Cancel
.
XPress the abutton.
The tire pressure values stored at the last
restart will continue to be monitored.
Tire pressure monitor
General notes
If at ire pressure monitor is installed, the vehi-
cle's wheels have sensors that monitor the tire
pressures in all four tires. The tire pressure mon-
itor warns you if the pressure drops in one or
more of the tires. The tire pressure monitor only
functions if the corresponding sensors are
installed in all wheels.
Information on tire pressures is displayed in the
multifunction display. After afew minutes of
driving, the current tire pressure of each tire is
shown in the Serv.
menu of the multifunction
display.
Example: current tire pressure display
For information on the message display, refer to
the "Checking the tire pressure electronically"
section (
Ypage 264).
262Tire pressure
Wheels and tires

In addition to the warning lamp,amessage
appears in the multifunction display. Observe
the information on display messages
(
Ypage 196).
It may take up to ten minutes for amalfunction
of the tire pressure monitor to be indicated .A
malfunction wil lbeindicated by the tire pres-
sure warning lamp flashing for approximately
one minute and then remaining lit. When the
malfunction has been rectified, the tire pressure
warning lamp goes out after afew minutes of
driving.
The tire pressure values indicated by the on-
board computer may differ from those meas-
ured at agas station with apressure gauge. The
tire pressures shown by the on-board computer
refer to those measured at sea level.Ath igh
altitudes, the tire pressure values indicated by a
pressure gauge are higher than those shown by the on-board computer. In this case, do not
reduce the tire pressures.
The operation of the tire pressure monitor can
be affected by interference from radi otransmit-
ting equipment (e.g. radi oheadphones, two-way
radios) that may be being operated in or near the vehicle.
Checking the tire pressure electroni-
cally
XMake sure that the SmartKey is in position 2
in the ignition lock (Ypage 115).
XPress the =or; button on the steering
wheel to select the Serv.menu.
XPress the9or: button to select
Tire Pressure.
XPress the abutton.
The current tire pressure of each tire is shown
in the multifunction display.
If the vehicle has been parked for over
20 minutes, the Tire pressure will be
displayed after driving afew minutesmessag eappears.
After ateach-in process, the tire pressure mon-
itor automatically detects new wheelsorn ew
sensors. As long as aclear allocation of the tire
pressure valu etothe individual wheel sisnot
possible, the Tire
PressureMonitorActivedisplay messag eisshown instead of the tire
pressure display. The tire pressures are already
being monitored.
If an emergency spare wheel is mounted, the
system may continue to show the tire pressure of the wheel that has been removed for
afew
minutes. If this occurs, note that the valu edis-
played for the positionw here the spare wheel is
mounted is not the same as the current tire
pressure of the emergency spare wheel.
Tire pressure monitor warning mes-
sages
If the tire pressure monitor detects apressure
loss in one or more tires, awarning messag eis
shown in the multifunction display. The yellow
tire pressure warning lamp then lights up.
RIf the Please Correct Tire Pressuremessag eappears in the multifunction display,
the tire pressure in at least one tire is too low.
The tire pressure must be corrected when the
opportunity arises.
RIf the Check Tiresmessag eappears in the
multifunction display, the tire pressure in at
least one tire has droppeds ignificantly. The
tires must be checked.
RIf the WarningTireMalfunctionmessage
appears in the multifunction display, the tire
pressure in at least one tire has droppeds ud-
denly.T he tires must be checked.
Observe the instructions and safety notes in the
display messages in the "Tires" section
(
Ypage 196).
If the wheel positions on the vehicle are rotated,
the tire pressures may be displaye dfor the
wrong positions for ashort time. This is rectified
after afew minutes of driving, and the tire pres-
sures are displaye dfor the correct positions.
Restarting the tire pressure monitor
When you restart the tire pressure monitor, all
existing warning messages are deleted and the
warning lamp sgoout. The monitor uses the cur-
rently set tire pressures as the reference values for monitoring. In most cases, the tire pressure
monitor wil lautomatically detect the new refer-
ence values after you have changed the tire
pressure. However, you can also define refer-
ence values manually as describedh ere. The tire
pressure monitor then monitors the new tire
pressure values.
XSet the tire pressure to the valu erecommen-
ded for the corresponding driving situation on
the Tire and Loading Information placard on
the driver's side B-pillar(
Ypage 258).
264Tire pressure
Wheelsa nd tires

Additionaltire pressure values for different
load scan also be found on the tire pressure
table on the insid eofthe fuel fille rflap
(
Ypage 258).
XMake sure thatt he tire pressure is correct on
al lf ou rw heels.
XMake sure thatt he SmartKeyisinp osition2
in the ignition lock.
XPress the =or; button on the steering
whee ltoselect the Serv.menu.
XPress the 9or: button to select
Tir ePressure.
XPress the abutton.
The multifunctio ndisplay shows the current
tire pressure for the individual tire sorthe
Tir epressure wil lbedisplayed
after drivin gafew minutesmessage.
XPress the :button.
The UseCurrentPressuresasNewRef‐erenceValuesmessage appear sinthe mul-
tifunctio ndisplay.
If youw ishtoc onfirm the restart:
XPress the abutton.
The TirePress.MonitorRestartedmes-
sage appear sinthe multifunctio ndisplay.
After driving for afew minutes, the system
checks whethe rthe current tire pressures are
withint he specified range.T he new tire pres-
sures ar ethen accepte dasreference values
and monitored.
If youw ishtoc ancelthe restart:
XPress the %button.
The tire pressure values stored at the last
restart will continue to be monitored.
Radio type approval fort he tire pres-
sure monitor
CountryRadio type approval number
USAFCC ID: MRXMW2433A
FCC ID: MRXGG4
FCC ID: MRXMC34MA4
CanadaIC:2 546A-MW2433A
IC:2 546A-GG4
IC:2 546A-MC34MA4
Loadin gthe vehicle
Instructio nlabel sfor tiresa nd loads
GWARNING
Overloaded tire scan overheat, causing a
blowout. Overloaded tire scan also impai rthe
steering and driving characteristics and lead
to brake failure. There is ariskofa ccident.
Observ ethe load rating of the tires. The load
rating must be at leas thalfoft he GAW Rof
your vehicle. Never overload the tire sby
exceeding the maximu mload.
Twoi nstructio nlabel sony ourvehicl eshowt he
maximu mpossibl eload.
(1) The Tire and Loading Informatio nplacard is
on the B-pillar on the driver's side .The Tire
and Loading Informatio nplacard shows the
maximu mpermissibl enumbe rofoccu-
pants and the maximu mpermissibl evehicle
load .Italsoc ontains details of the tire sizes
and corresponding pressures for tires
mounted at the factory.
(2) The vehicl eide ntificatio nplate is on the
B-pillar on the driver's side .The vehicle
identificatio nplate informs yo uofthe gross
vehicl eweigh trating .Iti smadeupoft he
vehicl eweigh t, allvehicl eoccupants, the
fuel and the cargo. Yo ucan also find infor-
matio nabout the maximu mgross axle
weight rating on the front and rea raxle.
The maximu mgross axl eweigh trating is
the maximu mweigh tthatc an be carrie dby
one axl e(
fro
nt or rea raxle) .Never exceed
the maximu mloadort he maximu mgross
axl ew eigh trating for the front or rea raxle.
:B-pillar, driver's side
Loadin gthe vehicle265
Wheel sand tires
Z

An arrow on the sidewall of the tire indicates its
correct direction of rotation.
Storingwheels
Store wheels thata renot being used in acool,
dry and preferably dark place .Protect the tires
from oil, grease, gasoline and diesel.
Mounting awheel
Preparin gthe vehicle
XStop the vehicl eonsolid,non-slippery and
level ground.
XApply the electri cparking brake manually.
XBring the front wheels into the straight-ahead
position.
XShift the transmission to position P.
XSwitch off the engine.
XVehicles withoutKEYLESS -GO:remove the
SmartKeyf rom the ignition lock.
XVehicles with KEYLESS-GO: open the driv-
er' sd oor.
The vehicl eelectronics now have status 0.
Thi sist he same as the SmartKeyh aving been
removed.
XVehicles with KEYLESS-GO: remove the
Start/Stop button from the ignition lock
(
Ypage 115).
XIf included in the vehicl eequipment ,remove
the tire-change tool kit from the vehicle.
XSafeguar dthe vehicl eagain st rolling away.
iDue to difference sinvehicleequipment ,not
al lv ehicles ar eequippe dwithat ire-change
tool kit. For informatio nonwhich tool sare
required to perfor mawheelchange on your
vehicle, consult an authorize dMercedes-
Benz Center.
Necessary tire-changing tool scan include, for
example:
RJack
RWheel chock
RLugw rench
Securin gthe vehicle to preven titfrom
rolling away
If your vehicl eisequippe dwithaw heelchock, it
can be found in the tire-change tool kit
(
Ypage 241).
The folding whee lchoc kisana dditional safety
measure to prevent the vehicl efrom rolling
away ,for exampl ewhenc hanging awheel .
XFoldb othp late su pwar ds:.
XFol do utlowe rplate ;.
XGuid ethe lugs on the lowe rplate full yinto the
openings in base plate =.
XPlace chocks or othersuitabl eitems under
the front and rea rofthe whee lthati sdiago -
nally opposite the whee lyou wish to change.
Raisin gthe vehicle
GWARNING
If yo udon ot positio nthe jack correctl yatthe
appropriate jacking point of the vehicle, the
jack could tip ove rwitht he vehicl eraised.
There is ariskofi njury.
Onlyp ositiont he jack at the appropriate jack-
ing point of the vehicle. The base of the jack
Changin gawheel275
Wheel sand tires
Z

vehicle. The wheelrim could otherwise be
damaged.
!Do not operate the tire inflation compressor
for longer than eigh tminutes at atime without
ab reak. It may otherwise overheat.
The tire inflation compressorc an be operated
again once it has cooled down.
XMount the collapsible spare whee lasdescri-
bed (Ypag e275).
The collapsible spare whee lmust be mounted
before it is inflated.
XRemove the tire inflation compressorf rom
the stowage space under the trunk floor
(
Ypag e241).
XPullplug ?out of the housing.
XTake the filler hose out of the housing.
XInsert the yellow hose connector of the filler
hose into the guide in the housing and push it
into the fixture until the hose connector
engages.
XRemove the cap from the valve on the col-
lapsibles pare wheel.
XScrew union nut :on the filler hose onto the
valve.
XMake sure the tire inflation compressor's on/
off switch Ais set to OFF.
XInsert plug ?into the socket of the cigarette
lighter or into a12Vpowersocket in your
vehicle.
XTurn the SmartKey to position 1in the ignition
lock (Ypag e115).
XPress on/off switch Aon the tire inflation
compressort oON.
The tire inflation compressoriss witched on.
The tire is inflated. The tire pressure is shown
on pressure gauge =.
XInflate the tire to the specified tire pressure. The specified tire pressure is printed on the
yellow label of the emergency spare wheel.
XWhen the specified tire pressure has been
reached, press on/off switch
AtoOFF,o n
the tire inflation compressor.
The tire inflation compressoriss witched off.
XTurn the SmartKey to position0in the ignition
lock.
XIf the tire pressure is highert han the specified
pressure, press pressure release button ;
until the correct tire pressure has been
reached.
XUnscrew union nut :on the filler hose from
the valve.
XScrew the cap onto the valve of the collapsi-
ble spare whee lagain.
XTo remove the filler hose from the tire inflation
compressor, push down the rocker switch on
the hose connector and pul lout the filler
hose.
XStow plug ?and the filler hose in the lower
section of the compressorh ousing.
XStow the tire inflation compressorint he vehi-
cle.
Emergency spare wheel281
Wheels and tires
Z