2017 MAZDA MODEL MX-5 RF instrument cluster

4–105
When Driving
i-ACTIVSENSE
To Operate the System
The High Beam Control System (HBC)
operates to switch the headlights
automatically between high and low
beams after the ignition is switched ON
and the headlight switch is in the AUTO
and high beam position.
The High Beam Control System (HBC)
determines that it is dark based on the
brightness of the surrounding area. At the
same time, the High Beam Control System
(HBC) indicator light (green) in the
instrument cluster illuminates.
NOTE
  When the vehicle speed is about
30 km/h (19 mph) or more, the
headlights automatically switch
to high beams when there are no
vehicles ahead or approaching in the
opposite direction.
 When the vehicle speed is less
than about 20 km/h (12 mph), the
High Beam Control System (HBC)
switches the headlights to low
beams.
  The low beams may not switch to
high beams when cornering.
  Operation of the High Beam Control
System (HBC) function can be
disabled. Refer to Personalisation
Features on page 9-10 .
Manual Switching
Switching to low beams
Shift the lever to the low beam position.
The High Beam Control System (HBC)
indicator light (green) turns off.
Switching to high beams
Turn the headlight switch to the
position.
The High Beam Control System (HBC)
indicator light (green) turns off and the
is illuminated.
/:A(.'',A'FKVKQPKPFD

4–109
When Driving
i-ACTIVSENSE
When the System Operates
1. The system goes on operation standby
when the LDWS switch is pressed and
the LDWS OFF indicator light in the
instrument cluster turns off.
2. Drive the vehicle in the centre of the
driving lane while the LDWS OFF
indicator light is turned off. The system
becomes operational when all of the
following conditions are met.
 

 
 The vehicle is driven in the centre
of the driving lane with the white
or yellow lines on the left and right
sides, or on either side.
 

 
 The vehicle speed is 65 km/h (41
mph) or faster.
 

 
 The vehicle is driven on a straight
road or road with gentle curves.
The LDWS does not operate in the
following cases:
 

 
 The system cannot detect white or
yellow lines.
 

 
 The vehicle speed is less than 60
km/h (37 mph).
 

 
 The vehicle is making a sharp turn.


 
 The vehicle is making a curve at an
inadequate speed.
NOTE
  The LDWS does not operate until the
system detects a white or yellow line
on either the left or right.
  When the system detects a white
or yellow line on one side only, the
system will activate the warning only
when the vehicle deviates on the side
where the white or yellow line is
being detected.
  The distance and warning sensitivity
(likelihood of a warning) which
the system uses to determine the
possibility of a lane departure can be
changed.
 Refer to Personalisation Features on
page 9-10 .
Auto cancel
In the following cases, the LDWS cancels
automatically and the LDWS warning
light in the instrument cluster turns on.
 


 The temperature inside the camera is
high or low.
 


 The windscreen around the camera is
foggy.
 


 The windscreen around the camera is
blocked by an obstruction, causing poor
forward visibility.
The LDWS is enabled automatically when
the operation conditions are met, and the
LDWS warning light turns off.
/:A(.'',A'FKVKQPKPFD

4–113
When Driving
i-ACTIVSENSE
NOTE
  The Blind Spot Monitoring (BSM) will operate when all of the following conditions
are met:
 


 The ignition is switched ON.



 The Blind Spot Monitoring (BSM) switch is pressed and the Blind Spot Monitoring
(BSM) OFF indicator light in the instrument cluster is turned off.
 


 The vehicle speed is about 30 km/h (19 mph) or faster. 

 The Blind Spot Monitoring (BSM) will not operate under the following circumstances.




 The vehicle speed falls below about 25 km/h (15 mph) even though the Blind Spot
Monitoring (BSM) OFF indicator light is turned off.
 


 The shift lever (manual transmission)/selector lever (automatic transmission) is
shifted to reverse (R) and the vehicle is reversing.
 
 In the following cases, the Blind Spot Monitoring (BSM) OFF indicator light turns
on and operation of the system is stopped. If the Blind Spot Monitoring (BSM) OFF
indicator light remains illuminated, have the vehicle inspected at an Authorised Mazda
Dealer as soon as possible.
 


 Some problem with the system including the Blind Spot Monitoring (BSM) warning
lights is detected.
 


 A large deviation in the installation position of a radar sensor (rear) on the vehicle
has occurred.
 


 There is a large accumulation of snow or ice on the rear bumper near a radar sensor
(rear). Remove any snow, ice or mud on the rear bumper.
 


 Driving on snow-covered roads for long periods.



 The temperature near the radar sensors (rear) becomes extremely hot due to driving
for long periods on slopes during the summer.
 


 The battery voltage has decreased. 

 Under the following conditions, the radar sensors (rear) cannot detect target objects or
it may be dif¿ cult to detect them.




 A vehicle is in the detection area at the rear in an adjacent driving lane but it does
not approach. The Blind Spot Monitoring (BSM) determines the condition based on
radar detection data.
 


 A vehicle is travelling alongside your vehicle at nearly the same speed for an
extended period of time.
 


 Vehicles approaching in the opposite direction.



 A vehicle in an adjacent driving lane is attempting to pass your vehicle.



 A vehicle is in an adjacent lane on a road with extremely wide driving lanes. The
detection area of the radar sensors (rear) is set at the road width of expressways.
/:A(.'',A'FKVKQPKPFD

4–117
When Driving
i-ACTIVSENSE
Blind Spot Monitoring (BSM) OFF
Indicator Light
 


 When the ignition is switched ON, the
malfunction warning light turns on
momentarily and then turns off after a
few seconds.
 


 The BSM OFF Indicator Light
illuminates when the Blind Spot
Monitoring (BSM) switch is pressed
to turn off the Blind Spot Monitoring
(BSM) and Rear Cross Traf¿ c Alert
(RCTA) systems.
 


 A malfunction in the system may
be indicated under the following
conditions. Have your vehicle inspected
at an Authorised Mazda Dealer.
 

 
 The light does not turn on when the
ignition is switched ON.
 

 
 The light remains turned on even if the
Blind Spot Monitoring (BSM) switch
is operated.
 

 
 It turns on while driving the vehicle.
Blind Spot Monitoring (BSM)
Switch
When the Blind Spot Monitoring
(BSM) switch is pressed, the Blind Spot
Monitoring (BSM) and Rear Cross Traf¿ c
Alert (RCTA) systems are turned off
and the BSM OFF Indicator Light in the
instrument cluster turns on.
If the switch is pressed again, the Blind
Spot Monitoring (BSM) and Rear Cross
Traf¿ c Alert (RCTA) systems become
operable and the BSM OFF Indicator
Light turns off.
/:A(.'',A'FKVKQPKPFD

4–123
When Driving
i-ACTIVSENSE
Adjustable Speed Limiter Display
The setting status of the adjustable speed limiter is displayed in the display in the instrument
cluster.
Stand-by display
Displays when the speed limiter switch is operated and the system is turned on.
Turns off when the system is turned off.
Setting display
Displays when the SET
switch is operated and the speed is set.
Cancel display
Displays when any of the following operations is done and the system is temporarily
cancelled.
 


 OFF/CANCEL switch is operated



 Accelerator pedal is strongly depressed
/:A(.'',A'FKVKQPKPFD

4–124
When Driving
i-ACTIVSENSE
Adjustable Speed Limiter Main Indication (White)/Adjustable Speed Limiter
Set Indication (Green), Adjustable Speed Limiter Main Indicator Light
(Amber)/Adjustable Speed Limiter Set Indicator Light (Green)
Type A instrument cluster
(Adjustable speed limiter main indication (white))
The indication display in white when the MODE switch is pressed and the adjustable speed
limiter is activated.
(Adjustable speed limiter set indication (green))
The indication display in green when a speed has been set.
Type B instrument cluster
(Adjustable speed limiter main indicator light (amber))
The indicator light illuminates amber when the MODE switch is pressed and the adjustable
speed limiter is activated.
(Adjustable speed limiter set indicator light (green))
The indicator light illuminates green when a speed has been set.
Speed Limiter Warning Beep
If the vehicle speed exceeds the set speed by about 3 km/h (2 mph) or more, a warning
sound operates continuously and the adjustable speed limiter display À ashes at the same
time. The warning sound operates and the display À ashes until the vehicle speed decreases
to the set speed or less.
Verify the safety of the surrounding area and adjust the vehicle speed by applying the
brakes. Additionally, keep a safer distance from the vehicles behind you.
/:A(.'',A'FKVKQPKPFD

4–125
When Driving
i-ACTIVSENSE
CAUTION
If the set speed is set lower than the current vehicle speed by pressing the SET or
RESUME/
switch, the warning beep is not activated for about 30 seconds even if the
vehicle speed is faster than the newly set speed by 3 km/h (2 mph). Be careful not to drive
over the set speed.
NOTE
When the system is temporarily cancelled by depressing the accelerator pedal fully, the
adjustable speed limiter display shows the cancel display. If the vehicle speed exceeds the
set speed by about 3 km/h (2 mph) or more while the cancel display is displayed, the set
speed display À ashes but the warning sound is not operated.
Activation/Deactivation
NOTE
When the ignition is switched off, the system status before it was turned off is maintained.
For example, if the ignition is switched off while the adjustable speed limiter is operating,
the system will be operable when the ignition is switched ON the next time.
Activation
(Type A Instrument Cluster)
Press the MODE switch to operate the system. The adjustable speed limiter screen is
displayed, and the adjustable speed limiter main indication displays in white.
NOTE
When the cruise control is operating after pressing the MODE switch, press the mode
switch again to switch to the adjustable speed limiter.
/:A(.'',A'FKVKQPKPFD

4–126
When Driving
i-ACTIVSENSE
(Type B Instrument Cluster)
Press the MODE switch to operate the system. The adjustable speed limiter screen is
displayed, and the adjustable speed limiter main indicator light (amber) turns on.
NOTE
When the cruise control is operating after pressing the MODE switch, press the mode
switch again to switch to the adjustable speed limiter.
Deactivation
To deactivate the system, do the following operations:
(Type A Instrument Cluster)
When a cruising speed has been set (adjustable speed limiter set indication displays in
green)
Long-press the OFF/CANCEL switch or press the OFF/CANCEL switch 2 times. The
adjustable speed limiter screen is no longer displayed and the adjustable speed limiter set
indication (green) does not display.
When a cruising speed has not been set (adjustable speed limiter main indication
displays in white)
Press the OFF/CANCEL switch. The adjustable speed limiter screen is no longer displayed
and the adjustable speed limiter main indication (white) does not display.
NOTE
When the MODE switch is pressed during adjustable speed limiter operation, the system
switches to the cruise control.
(Type B Instrument Cluster)
When a cruising speed has been set (adjustable speed limiter set indicator light (green)
turns on)
Long-press the OFF/CANCEL switch or press the OFF/CANCEL switch 2 times. The
adjustable speed limiter screen is no longer displayed and the adjustable speed limiter set
indicator light (green) turns off.
/:A(.'',A'FKVKQPKPFD