2017 MAZDA MODEL MX-5 RF engine oil

6–19
Maintenance and Care
Owner Maintenance
Vehicle Engine Control Unit Reset Procedure
NOTE
This procedure is intended for vehicles with the engine oil À exible maintenance setting
selected.
After replacing the engine oil, have a repair shop such as an Authorised Mazda Repairer
perform the initialization (engine oil data resetting) of the recorded value. If the value
recorded by the computer is not initialized, the wrench indicator light may not turn off or it
may turn on earlier than normal.
NOTE
The initialization (engine oil data resetting) of the recorded value can be performed using
the following procedure:
1. Switch the ignition OFF.
2. Switch the ignition ON with the selector pressed, and press and hold the selector for
about 5 seconds until the master warning light
À ashes. 
Selector
3. After the master warning light À ashes for several seconds, the initialization is
completed.
/:A(.'',A'FKVKQPKPFD

6–20
Maintenance and Care
Owner Maintenance
Inspecting Engine Oil Level
1. Be sure the vehicle is on a level
surface.
2. Warm up the engine to normal
operating temperature.
3. Turn it off and wait at least 5 minutes
for the oil to return to the sump.
4. Pull out the dipstick, wipe it clean, and
reinsert it fully.
MIN MAX
OK
5. Pull it out again and examine the level.
The level is normal if it is between the
MIN and MAX marks.
If it is near or below MIN, add enough
oil to bring the level to MAX.
CAUTION
Do not over¿ ll the engine oil. This may
cause engine damage.
6. Make sure the O-ring on the dipstick is
positioned properly before reinserting
the dipstick.
7. Reinsert the dipstick fully.
Engine Coolant
Inspecting Coolant Level
WARNING
Do not use a match or live À ame in the
engine compartment. DO NOT ADD
COOLANT WHEN THE ENGINE IS
HOT:
A hot engine is dangerous. If the
engine has been running, parts of the
engine compartment can become very
hot. You could be burned. Carefully
inspect the engine coolant in the
coolant reservoir, but do not open it.
Pull over to a safe location, then
switch the ignition off and make sure
the fan is not running before
attempting to work near the cooling
fan:
Working near the cooling fan when it
is running is dangerous. The fan could
continue running inde¿ nitely even if
the engine has stopped and the engine
compartment temperature is high. You
could be hit by the fan and seriously
injured.
Do not remove either
cooling system cap when the engine
and radiator are hot:
When the engine and radiator are hot,
scalding coolant and steam may shoot
out under pressure and cause serious
injury.
/:A(.'',A'FKVKQPKPFD

6–24
Maintenance and Care
Owner Maintenance
Body Lubrication
All moving points of the body, such as
door and bonnet hinges and locks, should
be lubricated each time the engine oil is
changed. Use a nonfreezing lubricant on
locks during cold weather.
Make sure the bonnet's secondary latch
keeps the bonnet from opening when the
primary latch is released.
Wiper Blades
CAUTION
  Hot waxes applied by automatic car
washers have been known to affect
the wiper's ability to clean windows.
  To prevent damage to the wiper
blades, do not use petrol, paraf¿ n,
paint thinner, or other solvents on or
near them.
  When the wiper lever is in the
AUTO position and the ignition is
switched ON, the wipers may move
automatically in the following cases:
 


 If the windscreen above the rain
sensor is touched.
 


 If the windscreen above the rain
sensor is wiped with a cloth.
 


 If the windscreen is struck with a
hand or other object.
 


 If the rain sensor is struck with a
hand or other object from inside
the vehicle.
  Be careful not to pinch hands or
¿ ngers as it may cause injury, or
damage the wipers. When washing or
servicing the vehicle, make sure the
wiper lever is in the OFF position.
Contamination of either the windscreen or
the blades with foreign matter can reduce
wiper effectiveness. Common sources are
insects, tree sap, and hot wax treatments
used by some commercial car washes.
If the blades are not wiping properly,
clean the window and blades with a good
cleaner or mild detergent; then rinse
thoroughly with clean water. Repeat if
necessary.
/:A(.'',A'FKVKQPKPFD

6–63
Maintenance and Care
Appearance Care
6. After cleaning is ¿ nished, continue
pressing the retractable fastback switch
in the close direction to close the rear
roof.
Refer to Closing the Roof on page
3-52 . Plastic Part Maintenance
 












 When cleaning the plastic lenses of
the lights, do not use petrol, paraf¿ n,
recti¿ ed spirit, paint, thinner, highly
acidic detergents, or strongly alkaline
detergents. Otherwise, these chemical
agents can discolour or damage the
surfaces resulting in a signi¿ cant loss
in functionality. If plastic parts become
inadvertently exposed to any of these
chemical agents, À ush with water
immediately.
 


 If plastic parts such as the bumpers
become inadvertently exposed to
chemical agents or À uids such as petrol,
oil, engine coolant, or battery À uid, it
could cause discolouration, staining,
or paint peeling. Wipe off any such
chemical agents or À uids using a soft
cloth immediately.
 


 High water temperature and high water
pressure car washers are available
depending on the type of high pressure
car washer device. If the car washer
nozzle is put too close to the vehicle or
aimed at one area for an extended period
of time, it could deform plastic parts or
damage the paint.
 


 Do not use wax containing compounds
(polish). Otherwise, it could result in
paint damage.
 


 In addition, do not use an electrical or
air tool to apply wax. Otherwise, the
frictional heat generated could result
in deformation of plastic parts or paint
damage.
/:A(.'',A'FKVKQPKPFD

7–33
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Signal Warning
Engine Oil Warning
Light This warning light indicates low engine oil pressure.
CAUTION
Do not run the engine if the oil pressure is low. Otherwise, it could result in
extensive engine damage.
If the light illuminates or the warning indication is displayed while driving:
1. Drive to the side of the road and park off the right-of-way on level ground.
2. Turn off the engine and wait 5 minutes for the oil to drain back into the sump.
3. Inspect the engine oil level 6-20 . If it's low, add the appropriate amount of engine
oil while being careful not to over¿ ll.
CAUTION
Do not run the engine if the oil level is low. Otherwise, it could result in extensive
engine damage.
4. Start the engine and check the warning light.
If the light remains illuminated even though the oil level is normal or after adding oil,
stop the engine immediately and have your vehicle towed to an expert repairer, we
recommend an Authorised Mazda Repairer.
(Red)
High Engine Coolant
Temperature Warning
Indication/Warning
Light
The light À ashes when the engine coolant temperature is extremely high, and
illuminates when the engine coolant temperature increases further.
Handling Procedure
Flashing light
Drive slowly to reduce engine load until you can ¿ nd a safe place to stop the vehicle
and wait for the engine to cool down.
Illuminated light
This indicates the possibility of overheating. Park the vehicle in a safe place
immediately and stop the engine.
Refer to Overheating 7-24 .
CAUTION
Do not drive the vehicle with the high engine coolant temperature warning light
illuminated. Otherwise, it could result in damage to the engine.
/:A(.'',A'FKVKQPKPFD

9–5
Speci¿ cations
Speci¿ cations
Lubricant Quality
Lubricant Classi¿ cation
Europe Except Europe
Engine oil
*1
Recommended Oils *2 Oil Quality
Mazda Original Oil Supra 0W-20
API SG/SH/SJ/SL/SM/SN or
ILSAC GF-II/GF-III/GF-IV/GF-V Mazda Original Oil Ultra 5W-30
Alternative Oil Quality
*3
API SL/SM/SN or
ACEA A3/A5 0W-20
5W-30
Coolant FL-22 type
Manual transmission oil Mazda Original Long Life Gear Oil IS
*4
Automatic transmission À uid JWS3309
Rear differential oil Mazda Long Life Hypoid Gear Oil SG1
Brake/Clutch À uid SAE J1703 or FMVSS116 DOT-3 or DOT-4
*1 Refer to Recommended Oil on page 6-17 .
Do not use oils which do not meet the above speci¿ cation or requirements. Use of unsuitable oil may lead to
engine damage which is not covered by the Mazda Warranty.
*2 Mazda Original Oils are specially designed/tested for the respective engine. For optimum performance we
recommend to use Mazda Original Oils at all times.
*3 If you are unable to ¿ nd a Mazda Original Oil, alternative oils meeting the listed speci¿ cation may also be used.
*4 Mazda Original Long Life Gear Oil IS is superior oil for optimum shift-feel. Using Mazda Original Long Life
Gear Oil IS is recommended.
If Mazda Original Long Life Gear Oil IS cannot be obtained, use standard oil (API Service GL-4 (SAE 75W-
90)). However, shifting in very low temperatures may become dif¿ cult.
/:A(.'',A'FKVKQPKPFD

9–6
Speci¿ cations
Speci¿ cations
Capacities
(Approximate Quantities)
Item Capacity
Engine
oil With oil ¿ lter replacement 4.3 L (4.5 US qt, 3.8 Imp qt)
Without oil ¿ lter replacement 4.1 L (4.3 US qt, 3.6 Imp qt)
Coolant SKYACTIV-G 1.5 Left-hand drive model 5.6 L (5.9 US qt, 4.9 Imp qt)
Right-hand drive model 5.8 L (6.1 US qt, 5.1 Imp qt)
SKYACTIV-G 2.0 Manual
transmission Left-hand drive model 6.0 L (6.3 US qt, 5.3 Imp qt)
Right-hand drive model 6.2 L (6.6 US qt, 5.5 Imp qt)
Automatic
transmission Saudi Arabia 6.2 L (6.6 US qt, 5.5 Imp qt)
Right-hand drive model 6.0 L (6.3 US qt, 5.3 Imp qt)
Except above 5.9 L (6.2 US qt, 5.2 Imp qt)
Manual transmission oil 2.0 L (2.1 US qt, 1.8 Imp qt)
Automatic transmission À uid 7.2 L (7.6 US qt, 6.3 Imp qt)
Rear differential oil 0.6 L (0.6 US qt, 0.5 Imp qt)
Fuel tank 45.0 L (11.9 US gal, 9.90 Imp gal)
Check oil and À uid levels with dipsticks or reservoir gauges.
Dimensions
Item Vehicle speci¿ cation
Soft top model Retractable fastback
model
Overall length 3,915 mm (154.1 in) 3,915 mm (154.1 in)
Overall width 1,735 mm (68.3 in) 1,735 mm (68.3 in)
Overall height 16 inch wheel vehicle 1,225 mm (48.2 in) 1,230 mm (48.4 in)
17 inch wheel vehicle 1,230 mm (48.4 in) 1,235 mm (48.6 in)
Front tread 1,495 mm (58.9 in) 1,495 mm (58.9 in)
Rear tread 1,505 mm (59.3 in) 1,505 mm (59.3 in)
Wheelbase 2,310 mm (90.9 in) 2,310 mm (90.9 in)
/:A(.'',A'FKVKQPKPFD

10–4
Index
Engine
Bonnet release ............................... 6-14
Coolant .......................................... 6-20
Engine compartment overview ..... 6-16
Exhaust gas.................................... 3-26
Oil .................................................. 6-17
Starting ............................................ 4-5
Engine Coolant Temperature
Gauge ......................................... 4-27, 4-36
Essential Information ............................ 6-2
Exhaust Gas ........................................ 3-26
Exterior Care ....................................... 6-53
Aluminium wheel maintenance..... 6-58
Bright-metal maintenance ............. 6-57
Cavity protection ........................... 6-57
Convertible Top (Retractable Fastback)
Maintenance .................................. 6-61
Convertible Top (Soft Top)
Maintenance .................................. 6-58
Maintaining the ¿ nish ................... 6-55
Paint damage touch-up .................. 6-57
Plastic part maintenance ................ 6-63
Undercoating ................................. 6-57
F
Flasher
Hazard warning ............................. 4-79
Headlights ..................................... 4-63
Flat Tyre ................................................ 7-3
Mounting the tyre .......................... 7-17
Removing a tyre ............................ 7-14
Floor Mat ............................................ 3-61
Fluid
Brake/Clutch ................................. 6-22
Washer ........................................... 6-23
Fluids
Classi¿ cation ................................... 9-5
Foot Brake ........................................... 4-81
Forward Sensing Camera (FSC) ....... 4-129 Fuel
Filler À ap and cap .......................... 3-27
Gauge ................................... 4-27, 4-36
Requirements................................. 3-24
Tank capacity .................................. 9-6
Fuel Consumption Display ................. 4-94
Fuel Economy Monitor ....................... 4-93
Control status display .................... 4-94
Effectiveness display ..................... 4-96
Ending screen display ................... 4-96
Fuel consumption display ............. 4-94
Fuel-Filler Flap
When fuel-¿ ller À ap cannot be
opened ........................................... 7-26
Fuses ................................................... 6-47
Panel description ........................... 6-50
Replacement .................................. 6-47
G
Gauges ................................................. 4-24
H
Hazard Warning Flasher ...................... 4-79
Hazardous Driving .............................. 3-60
Head Restraint ....................................... 2-8
Headlight Washer ................................ 4-77
Headlights
Coming home light ........................ 4-68
Control........................................... 4-63
Flashing ......................................... 4-68
High-low beam .............................. 4-68
Leaving home light ....................... 4-69
Levelling ....................................... 4-70
Running lights ............................... 4-70
Washer ........................................... 4-77
High Beam Control System (HBC) ... 4-103
High Beam Control System (HBC)
indicator light (green) .................. 4-105
Hill Launch Assist (HLA) ................... 4-84
Horn .................................................... 4-79
/:A(.'',A'FKVKQPKPFD