2017 MAZDA MODEL CX-5 tire type

2–40
Essential Safety Equipment
Child Restraint
5. To get the retractor into the automatic locking mode, pull the shoulder belt
portion of the seat belt until the entire
length of the belt is out of the retractor.
6. Push the child-restraint system fi rmly
into the vehicle seat. Be sure the
belt retracts as snugly as possible. A
clicking noise from the retractor will
be heard during retraction if the system
is in automatic locking mode. If the
belt does not lock the seat down tight,
repeat the previous step and also this
one.
NOTE
   Inspect this function before each use of
the child-restraint system. You should
not be able to pull the shoulder belt
out of the retractor while the system is
in the automatic locking mode. When
you remove the child-restraint system,
be sure the belt fully retracts to return
the system to emergency locking mode
before occupants use the seat belts.
  Follow the child-restraint system
manufacturer's instructions carefully.
 Depending on the type of child-restraint system, it may not employ seat belts
which are in automatic locking mode.

7. Seat your child safely in the child- restraint system and secure the child
according to the instructions from the
child-restraint system manufacturer. 8. Switch the ignition ON and make sure
the front passenger air bag deactivation
indicator light illuminates after
installing a child-restraint system on
the front passenger seat.
If the front passenger air bag deactivation indicator light does not
illuminate, remove the child-restraint
system, switch the ignition to OFF, and
then re-install the child-restraint system
(page 2-61 ).


CX-5_8FN1-EA-16L_Edition1.indb 402016/12/12 10:05:23

3–50
Before Driving
Driving Tips
Hazardous Driving
WARNING
Be extremely careful if it is necessary to
downshift on slippery surfaces: Downshifting into lower gear
while driving on slippery surfaces is
dangerous. The sudden change in tire
speed could cause the tires to skid. This
could lead to loss of vehicle control
and an accident.

Avoid sharp turns, excessive speed and
abrupt maneuvers when driving this
vehicle: Sharp turns, excessive speed and
abrupt maneuvering of this vehicle
are dangerous as it could result in the
increased risk of loss of vehicle control,
vehicle roll-over, personal injury or
death.
This vehicle has a higher center of
gravity. Vehicles with a higher center of
gravity such as utility vehicles handle
diff erently than vehicles with a lower
center of gravity.
Utility vehicles are not designed for
cornering at high speeds any more
than low profi le sports cars are
designed to perform satisfactorily
under off -road conditions.
In addition, utility vehicles have a
signifi cantly higher rollover rate than
other types of vehicles.
In a rollover crash, an unbelted person
is signifi cantly more likely to die than a
person wearing a seat belt.

When driving on ice or in water, snow,
mud, sand, or similar hazards:
  Be cautious and allow extra distance for
braking.
   Avoid sudden braking and sudden
maneuvering.
   Do not pump the brakes. Continue to
press down on the brake pedal.
 Refer to Antilock Brake System (ABS) on page 4-82 .
  If you get stuck, select a lower gear and
accelerate slowly. Do not spin the front
wheels.
   For more traction in starting on slippery
surfaces such as ice or packed snow,
use sand, rock salt, chains, carpeting, or
other nonslip material under the front
wheels.

NOTE
Use snow chains only on the front wheels.
CX-5_8FN1-EA-16L_Edition1.indb 502016/12/12 10:05:37

3–52
Before Driving
Driving Tips
Winter Driving
Carry emergency gear, including tire
chains, window scraper, fl ares, a small
shovel, jumper cables, and a small bag of
sand or salt.
Ask an Authorized Mazda Dealer to check
the following:
   Have the proper ratio of antifreeze in the
radiator.
 Refer to Engine Coolant on page 6-25 .
  Inspect the battery and its cables. Cold
reduces battery capacity.
   Use an engine oil appropriate for the
lowest ambient temperatures that the
vehicle will be driven in (page 6-23 ).
  Inspect the ignition system for damage
and loose connections.
   Use washer fl uid made with antifreeze—
but do not use engine coolant antifreeze
for washer fl uid (page 6-27 ).

NOTE
  Remove snow before driving. Snow left
on the windshield is dangerous as it
could obstruct vision.
  Do not apply excessive force to a
window scraper when removing ice or
frozen snow on the mirror glass and
windshield.
  Never use warm or hot water for
removing snow or ice from windows and
mirrors as it could result in the glass
cracking.
  Drive slowly. Braking performance
can be adversely affected if snow or
ice adheres to the brake components. If
this situation occurs, drive the vehicle
slowly, releasing the accelerator pedal
and lightly applying the brakes several
times until the brake performance
returns to normal.

Snow Tires
Use snow tires on all four wheels
Do not go faster than 120 km/h (75 mph)
while driving with snow tires. In fl ate snow
tires 30 kPa (0.3 kgf/cm
2 , 4.3 psi) more
than recommended on the tire pressure
label (driver's door frame), but never
more than the maximum cold-tire pressure
shown on the tires.

Except Mexico
The vehicle is originally equipped with
all season radials designed to be used all
year around. In some extreme climates you
may fi nd it necessary to replace them with
snow tires during the winter months to
further improve traction on snow and ice
covered roads.
Mexico
The vehicle is originally equipped with
summer tires designed for optimum
traction on wet and dry roads. If your
vehicle is to be used on snow and ice
covered roads, Mazda recommends that
you replace the tires originally equipped
on your vehicle with snow tires during the
winter months.
WARNING
Use only the same size and type tires
(snow, radial, or non-radial) on all four
wheels: Using tires diff erent in size or type is
dangerous. Your vehicle's handling
could be greatly aff ected and result in
an accident.

CAUTION
Check local regulations before using
studded tires.

CX-5_8FN1-EA-16L_Edition1.indb 522016/12/12 10:05:38

4–90
When Driving
i-ACTIV AWD
Tires and Tire Chains
The condition of the tires plays a large
role in the performance of the vehicle.
Moreover, to prevent adverse effects to the
drive assembly, please note the following:
Tires
  When replacing tires, always replace all
front and rear tires at the same time.
   All tires must be of the same size,
manufacture, brand and tread pattern.
Pay particular attention when equipping
snow or other types of winter tires.
   Do not mix tread-worn tires with normal
tires.
   Inspect tire in fl ation pressures at the
specifi ed periods adjust to the speci fi ed
pressures.

NOTE
Check the tire in fl ation pressure label
attached to driver's door frame for the
correct tire in fl ation pressure.
   Make sure to equip the vehicle with
genuine wheels of the speci fi ed size, on
all wheels. With AWD, the system is
calibrated for all four wheels being of
the same dimensions.

Tire chains
   Install tire chains to the front tires.  Do not use tire chains on the rear
wheels.
   Do not drive the vehicle faster than
30 km/h (19 mph) with the tire chains
installed.
   Do not drive the vehicle with tire chains
on road conditions other than snow or
ice.

Towing
If the vehicle requires towing, have it
towed with all four wheels completely off
the ground.
Refer to Towing Description on page
7-20 .
CX-5_8FN1-EA-16L_Edition1.indb 902016/12/12 10:06:04

4–136
When Driving
i-ACTIVSENSE
WARNING
Do not rely completely on the Lane-keep Assist System (LAS) & Lane Departure
Warning System (LDWS):
 The Lane-keep Assist System (LAS) & Lane Departure Warning System (LDWS) is not an automatic driving system. In addition, the system is not designed to compensate for a
driver's lack of caution, and over-reliance on the system could lead to an accident.
 The detection ability of the Lane-keep Assist System (LAS) & Lane Departure Warning System (LDWS) is limited. Always stay on course using the steering wheel and drive
with care.

Do not use the Lane-keep Assist System (LAS) & Lane Departure Warning System
(LDWS) in the following cases: The system may not operate adequately according to the actual driving conditions,
resulting in an accident.
 Driving on roads with tight curves. Driving under bad weather conditions (rain, fog, and snow). Slippery roads such as ice or snow-bound roads. Roads with heavy traffi c and insuffi cient distance between vehicles. Roads with no white (yellow) lane lines. Narrow roads resulting from road construction or lane closures. The vehicle is driven on a temporary lane or section with a closed lane resulting from road construction where there may be multiple white (yellow) lane lines or they are
interrupted.
 The tire pressures are not adjusted to the specifi ed pressure. Tires of a diff erent specifi ed size are used, such as an emergency spare tire.
CAUTION
Heed the following cautions so that the Lane-keep Assist System (LAS) & Lane Departure
Warning System (LDWS) can operate normally.
 Do not modify the suspensions. Always use wheels of the specifi ed type and size for the front and rear wheels. Consult an Authorized Mazda Dealer for tire replacement.

CX-5_8FN1-EA-16L_Edition1.indb 1362016/12/12 10:06:13

4–175
When Driving
Tire Pressure Monitoring System
When changing tires yourself
If you or someone else changes tires, you
or someone else can also undertake the
steps for the TPMS to complete the ID
signal code registration.

1. After tires have been changed, switch the ignition ON, then back to ACC or
OFF.
2. Wait for about 15 minutes.
3. After about 15 minutes, drive the vehicle at a speed of at least 25 km/h
(16 mph) for 10 minutes and the tire
pressure sensor ID signal code will be
registered automatically.

NOTE
If the vehicle is driven within about 15
minutes of changing tires, the tire pressure
monitoring system warning light will fl ash
because the sensor ID signal code would
not have been registered. If this happens,
park the vehicle for about 15 minutes,
after which the sensor ID signal code will
register upon driving the vehicle for
10 minutes.

Replacing tires and wheels
CAUTION
 When replacing/repairing the tires or wheels or both, have the work done by
an Authorized Mazda Dealer, or the tire
pressure sensors may be damaged.
 The wheels equipped on your Mazda are specially designed for installation
of the tire pressure sensors. Do not use
non-genuine wheels, otherwise it may
not be possible to install the tire pressure
sensors.

Be sure to have the tire pressure sensors
installed whenever tires or wheels are
replaced.
When having a tire or wheel or both
replaced, the following types of tire
pressure sensor installations are possible.
   The tire pressure sensor is removed from
the old wheel and installed to the new
one.
   The same tire pressure sensor is used
with the same wheel. Only the tire is
replaced.
   A new tire pressure sensor is installed to
a new wheel.

NOTE
   The tire pressure sensor ID signal
code must be registered when a new
tire pressure sensor is purchased. For
purchase of a tire pressure sensor and
registration of the tire pressure sensor
ID signal code, consult an Authorized
Mazda Dealer.
  When reinstalling a previously removed
tire pressure sensor to a wheel, replace
the grommet (seal between valve body/
sensor and wheel) for the tire pressure
sensor.

CX-5_8FN1-EA-16L_Edition1.indb 1752016/12/12 10:06:20

5–12
Interior Features
Climate Control System
Temperature control dial
This dial controls temperature. Turn it
clockwise for hot and counterclockwise
for cold.
  When the DUAL switch is off: Turn the driver temperature control dial
to control the temperature throughout
the entire cabin.
  When the DUAL switch is on: Turn the driver or front passenger
temperature control dial to
independently control the temperature
on each side of the cabin.

NOTE
  The climate control system changes to
the individual operation mode ( DUAL
switch indicator light illuminated) by
turning the front passenger temperature
control dial even when the DUAL switch
is off, which allows individual control
of the set temperature for the driver and
front passenger.
  The temperature units for the
temperature setting display can be
changed in conjunction with the
temperature units for the outside
temperature display.
 (Type A instrument cluster) Refer to Outside Temperature Display on page 4-24 .
 (Type B instrument cluster) Refer to Outside Temperature Display on page 4-17 .

Fan control switch
The fan has seven speeds. The selected
speed will be displayed.
Mode selector switch
The desired air fl ow mode can be selected
(page 5-6 ).
NOTE
   With the air fl ow mode set to the
position and the temperature control
dial set at a medium temperature,
heated air is directed to the feet and air
at a comparably lower temperature will
fl ow through the central, left and right
vents.
   To set the air vent to , press the
windshield defroster switch.
   In the or position, the air
conditioner is automatically turned on
and the outside air position is
automatically selected to defrost the
windshield. In the
or position, the
outside air position cannot be changed
to the recirculated air position.

A/C switch
Pressing the A/C switch while the AUTO
switch is turned on will turn off the air-
conditioning (cooling/dehumidifying
functions).
The on/off of the air-conditioning switches
each time the A/C switch is pressed.
NOTE
   The air conditioner operates when the
A/C switch is pressed while the air
conditioner is turned off.
  The air conditioner may not function
when the outside temperature
approaches 0 °C (32 °F).

CX-5_8FN1-EA-16L_Edition1.indb 122016/12/12 10:06:25

5–39
Interior Features
Audio Set [Type A (non-touchscreen)]
8. Prompt: “Start the pairing process on your Bluetooth ® device. Your pairing
code is 0000 (XXXX). Input this on
your Bluetooth
® device when prompted
on the device. See device manual for
instructions.”
9. Using the device, perform a search for the Bluetooth
® device (Peripheral
device).
NOTE
For the operation of the device, refer to its
instruction manual.

10. Select “Mazda” from the device list searched by the device.
11. Input the 4-digit pairing code to the device.
12. Prompt: “Please say the name of the device after the beep.”
13. Say: [Beep] “XXXX - - -” (Say a “device tag”, an arbitrary name for the
device.) Example: “Stan's device.”
NOTE
Say a paired “device tag” within
10 seconds.
If more than two devices are to be paired,
they cannot be paired with the same or
similar “device tag”.

14. Prompt: “XXXXXX - - - (Ex. “Stan's device”) (Device tag). Is this correct?”
15. Say: [Beep] “Yes”
16. Prompt: “Pairing complete”


After a device is registered, the system
automatically identi fi es the device. By
activating Bluetooth
® Hands-Free again,
or by activating Bluetooth ® Hands-Free
fi rst after switching the ignition from
OFF to ACC, the system reads out a voice
guidance, “XXXXXX - - - (Ex. “Stan's
device”) (Device tag) is connected”.
NOTE
   When the pairing is completed, the
symbol is displayed.
   Some Bluetooth ® audio devices need a
certain amount of time before the

symbol is displayed.
   Device registration can also be done by
operating the audio unit.
  Depending on the device, the
registration status may be lost after a
certain period of time. If this occurs,
repeat the entire process from Step 1.

Registered device read-out
Bluetooth
® Hands-Free can read-out the
devices registered to its system.
NOTE
Do this function only when parked. It is
too distracting to attempt while driving
and you may make too many errors to be
effective.

1. Press the pick-up button or talk button with a short press.
2. Say: [Beep] “Setup”
3. Prompt: “Select one of the following: Pairing options, con fi rmation prompts,
language, passcode, select phone or
select music player.”
4. Say: [Beep] “Pairing options”
5. Prompt: “Select one of the following: Pair, Edit, Delete, List, or Set Pairing
Code”
6. Say: [Beep] “List”
CX-5_8FN1-EA-16L_Edition1.indb 392016/12/12 10:06:32