2017 MAZDA MODEL CX-5 instrument cluster

4–14 3
When Driving
i-ACTIVSENSE
Drive the vehicle in the center of the
driving lane while the Lane-keep Assist
System (LAS) & Lane Departure Warning
System (LDWS) OFF indicator light in the
instrument cluster is turned off.
The system becomes operational when all
of the following conditions are met.
  The system detects white (yellow) lane
lines on both the right and left sides or
on either side.
   The vehicle speed is about 60 km/h
(37 mph) or faster.
   The vehicle is driven on a straight road
or road with gentle curves.
   The engine is running.
The Lane-keep Assist System (LAS) &
Lane Departure Warning System (LDWS)
goes on stand-by status in the following
cases:
  The system cannot detect white (yellow)
lane lines.
   The vehicle speed is less than about
60 km/h (37 mph).
   The vehicle is making a sharp curve.  The vehicle is making a curve at an
inappropriate speed.

NOTE
   The Lane-keep Assist System (LAS)
& Lane Departure Warning System
(LDWS) remains on stand-by until it
detects white (yellow) lines on both the
left and right sides, or on either side.
  When the system detects a white
(yellow) lane line on one side only, the
system will not activate warnings for the
lane line on the side that is not being
detected.
  The distance and warning sensitivity
(likelihood of a warning) which the
system uses to determine the possibility
of a lane departure can be changed.
 Refer to Setting Change (Personalization Features) on page
9-11 .

Vehicle lane line display
When the Lane-keep Assist System
(LAS) & Lane Departure Warning System
(LDWS) becomes operational while
on standby, the vehicle lane lines are
displayed in the multi-information display.
The system changes to operational status
display when the system detects a white
(yellow) line on either the left or right.
(Stand-by status)


(Operational status)


CX-5_8FN1-EA-16L_Edition1.indb 1432016/12/12 10:06:15

4–162
When Driving
i-ACTIVSENSE
*Some models.
Radar Sensor (Front) *
Your vehicle is equipped with a radar sensor (front).
The following systems also use the radar sensor (front).
  Distance Recognition Support System (DRSS)  Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go\
function)  Smart Brake Support (SBS)
The radar sensor (front) functions by detecting the radio waves re fl ected off a vehicle ahead
or an obstruction sent from the radar sensor.
The radar sensor (front) is mounted behind the front emblem.

Radar sensor (front)

If “Front Radar Sensor Blocked” is displayed in the multi-informat\
ion display of the
instrument cluster, clean the area around the radar sensor (front).
CX-5_8FN1-EA-16L_Edition1.indb 1622016/12/12 10:06:17

4–169
When Driving
Cruise Control
NOTE
  The cruise control speed setting cannot
be performed under the following
conditions:
  (Automatic transaxle)  The selector lever is in the P or N
position.
  (Manual transaxle)  The shift lever is in the neutral
position.
  The parking brake is applied.   Release the SET/ or RESUME/
switch at the desired speed, otherwise
the speed will continue increasing while
the RESUME/
switch is pressed and
held, and continue decreasing while the
SET/
switch is pressed and held
(except when the accelerator pedal is
depressed).
   On a steep grade, the vehicle may
momentarily slow down while ascending
or speed up while descending.
  The cruise control will cancel if the
vehicle speed decreases below 21 km/h
(13 mph) when the cruise control is
activated, such as when climbing a
steep grade.
  The cruise control may cancel at about
15 km/h (9 mph) below the preset speed,
such as when climbing a long, steep
grade.

The vehicle speed preset using the cruise
control is displayed in the instrument
cluster and the active driving display
(vehicles with active driving display).

Type A Instrument Cluster
Type B Instrument ClusterMulti-information Display
Active Driving Display

To Increase Cruising Speed
Follow either of these procedures.
To increase speed using cruise control
switch
Press the RESUME/
switch and hold it.
Your vehicle will accelerate. Release the
switch at the desired speed.

Press the RESUME/
switch and release
it immediately to adjust the preset speed.
Multiple operations will increase the
preset speed according to the number of
times it is operated.
Increasing speed with a single
RESUME/
switch operation
Instrument cluster display for vehicle
speed indicated in km/h: 1 km/h (0.6 mph)
Instrument cluster display for vehicle
speed indicated in mph: 1 mph (1.6 km/h)
CX-5_8FN1-EA-16L_Edition1.indb 1692016/12/12 10:06:19

4–170
When Driving
Cruise Control
To increase speed using accelerator
pedal
Depress the accelerator pedal to accelerate
to the desired speed. Press the SET/

switch and release it immediately.
NOTE
Accelerate if you want to speed up
temporarily when the cruise control is on.
Greater speed will not interfere with or
change the set speed. Take your foot off the
accelerator to return to the set speed.

To Decrease Cruising Speed
Press the SET/ switch and hold it. The
vehicle will gradually slow.
Release the switch at the desired speed.

Press the SET/
switch and release it
immediately to adjust the preset speed.
Multiple operations will decrease the
preset speed according to the number of
times it is operated.
Decreasing speed with a single SET/

switch operation
Instrument cluster display for vehicle
speed indicated in km/h: 1 km/h (0.6 mph)
Instrument cluster display for vehicle
speed indicated in mph: 1 mph (1.6 km/h)
To Resume Cruising Speed at More Than 25 km/h (16 mph)
If the cruise control system temporarily
canceled (such as by applying the brake
pedal) and the system is still activated, the
most recent set speed will automatically
resume when the RESUME/
switch is
pressed.
If vehicle speed is below 25 km/h
(16 mph), increase the vehicle speed up to
25 km/h (16 mph) or more and press the
RESUME/
switch.
To Temporarily Cancel
To temporarily cancel the system, use one
of these methods:
   Slightly depress the brake pedal.  (Manual transaxle)  Depress the clutch pedal.   Press the OFF/CANCEL switch.
If the RESUME/ switch is pressed when
the vehicle speed is 25 km/h (16 mph) or
higher, the system reverts to the previously
set speed.
NOTE
   If any of the following conditions occur,
the cruise control system is temporarily
canceled.
  The parking brake is applied.  (Automatic transaxle)  The selector lever is in the P or N
position.
  (Manual transaxle)  The shift lever is in the neutral
position.
  When the cruise control system is
temporarily canceled by even one of the
applicable cancel conditions, the speed
cannot be re-set.
  (Automatic transaxle)  The cruise control cannot be cancelled
while driving in manual mode (selector
lever shifted from D to M position).
Therefore, engine braking will not be
applied even if the transaxle is shifted
down to a lower gear. If deceleration is
required, lower the set speed or depress
the brake pedal.

CX-5_8FN1-EA-16L_Edition1.indb 1702016/12/12 10:06:19

4–172
When Driving
Tire Pressure Monitoring System
*Some models.
Tire Pressure Monitoring System *
The Tire Pressure Monitoring System (TPMS) monitors the pressure for each tire.
If tire pressure is too low in one or more tires, the system will inform\
the driver via the
warning light in the instrument cluster and by the warning beep sound.
Refer to Warning Indication/Warning Lights on page 4-33 .
Refer to Tire Infl ation Pressure Warning Beep on page 7-42 .

The tire pressure sensors installed on each wheel send tire pressure dat\
a by radio signal to
the receiver unit in the vehicle.

Tire pressure sensors
NOTE
When the ambient temperature is low due to seasonal changes, tire temperatures are also
lower. When the tire temperature decreases, the air pressure decreases as well. The TPMS
warning light may illuminate more frequently. Visually inspect the tires daily before driving,
and check tire pressures monthly with a tire pressure gauge. When checking tire pressures,
use of a digital tire pressure gauge is recommended.


TPMS does not alleviate your need to check the pressure and condition of\
all four tires
regularly.
CX-5_8FN1-EA-16L_Edition1.indb 1722016/12/12 10:06:19

5–12
Interior Features
Climate Control System
Temperature control dial
This dial controls temperature. Turn it
clockwise for hot and counterclockwise
for cold.
  When the DUAL switch is off: Turn the driver temperature control dial
to control the temperature throughout
the entire cabin.
  When the DUAL switch is on: Turn the driver or front passenger
temperature control dial to
independently control the temperature
on each side of the cabin.

NOTE
  The climate control system changes to
the individual operation mode ( DUAL
switch indicator light illuminated) by
turning the front passenger temperature
control dial even when the DUAL switch
is off, which allows individual control
of the set temperature for the driver and
front passenger.
  The temperature units for the
temperature setting display can be
changed in conjunction with the
temperature units for the outside
temperature display.
 (Type A instrument cluster) Refer to Outside Temperature Display on page 4-24 .
 (Type B instrument cluster) Refer to Outside Temperature Display on page 4-17 .

Fan control switch
The fan has seven speeds. The selected
speed will be displayed.
Mode selector switch
The desired air fl ow mode can be selected
(page 5-6 ).
NOTE
   With the air fl ow mode set to the
position and the temperature control
dial set at a medium temperature,
heated air is directed to the feet and air
at a comparably lower temperature will
fl ow through the central, left and right
vents.
   To set the air vent to , press the
windshield defroster switch.
   In the or position, the air
conditioner is automatically turned on
and the outside air position is
automatically selected to defrost the
windshield. In the
or position, the
outside air position cannot be changed
to the recirculated air position.

A/C switch
Pressing the A/C switch while the AUTO
switch is turned on will turn off the air-
conditioning (cooling/dehumidifying
functions).
The on/off of the air-conditioning switches
each time the A/C switch is pressed.
NOTE
   The air conditioner operates when the
A/C switch is pressed while the air
conditioner is turned off.
  The air conditioner may not function
when the outside temperature
approaches 0 °C (32 °F).

CX-5_8FN1-EA-16L_Edition1.indb 122016/12/12 10:06:25

6–4
Maintenance and Care
Scheduled Maintenance
Scheduled Maintenance (U.S.A., Canada, and Puerto Rico)
Follow Schedule 1 if the vehicle is operated mainly where none of the fo\
llowing conditions
(severe driving conditions)apply.
  Repeated short-distance driving  Driving in dusty conditions  Driving with extended use of brakes  Driving in areas where salt or other corrosive materials are used  Driving on rough or muddy roads  Extended periods of idling or low-speed operation  Driving for long periods in cold temperatures or extremely humid climate\
s  Driving in extremely hot conditions  Driving in mountainous conditions continually
If any do apply, follow Schedule 2. (Canada residents follow Schedule 2.)
Vehicles using Engine Oil Flexible Maintenance
Engine Oil Flexible Maintenance is selected by default for U.S.A. and Pu\
erto Rico residents.
If any following conditions do apply, follow Schedule 2 with engine oil fi xed maintenance.
   Extended periods of idling or low-speed operation such as police car, taxi or driving
school car
   Driving in dusty conditions
The vehicle calculates the remaining oil life based on engine operating \
conditions. The
vehicle lets you know when an oil change is due by illuminating the wren\
ch indicator light
in the instrument cluster. Change the oil as soon as possible within the next 1000 km
(600 mile) or 15 days. Refer page 6-16 for the details.
NOTE
  Please ensure that the Flexible Oil Maintenance Setting is reset after each Oil and Filter
replacement.
  For maintenance guidelines beyond the miles/months listed, follow the ma\
intenance
intervals provided in the Scheduled Maintenance Tables.

CX-5_8FN1-EA-16L_Edition1.indb 42016/12/12 10:07:05

6–16
Maintenance and Care
Scheduled Maintenance
Maintenance Monitor
Maintenance Monitor (Type A)
Based on the engine operating conditions, the onboard computer in your v\
ehicle calculates
the remaining oil life in the United States and Puerto Rico. The wrench indicator light in the
instrument cluster will be illuminated when remaining oil life becomes l\
ess than 1,000 km
(600 mile), or remaining days are less than 15 (whichever comes fi rst).
The system must be reset whenever replacing the engine oil.
Reset method
Press and hold the dashboard illumination knob with the ignition switche\
d off, then switch
it on. Keep pressing the dashboard illumination knob for more than 5 sec\
onds. The master
warning light will fl ash for a few seconds when the reset is completed.

Dashboard illumination knob

Maintenance Monitor (Type B)
1. Select the icon on the home screen to display the “Applications” screen.
2. Select “Vehicle Status Monitor”.
3. Select “Maintenance” to display the maintenance list screen.
4. Switch the tab and select the setting item you want to change.

CX-5_8FN1-EA-16L_Edition1.indb 162016/12/12 10:07:06