2017 MAZDA MODEL CX-5 ECO mode

5–128
Interior Features
Audio Set [Type B (touchscreen)]
Symptom Cause Solution method
Unable to perform pairing The Bluetooth
® function and the
Find Mode/Visible setting *1 on the
device may turn off automatically
after a period of time has elapsed
depending on the device. Check whether the Bluetooth ®
function and the Find Mode/Visible
setting
*1 on the device are turned on
and pairing or reconnect.
Does not connect automatically
when starting the engine
Automatically connects, but then
disconnects suddenly
Disconnects intermittently
The device is in a location in which
radio wave interference can occur
easily, such as inside a bag in a rear
seat, in a rear pocket of a pair of
pants. Move the device to a location in
which radio wave interference is less
likely to occur.
Does not connect automatically
when starting the engine The pairing information is updated
when the device OS is updated. Perform pairing using the following
procedure:
1. Delete the applicable Bluetooth ®
device on the Mazda Connect.
2. Delete “Mazda” from the Bluetooth
® search screen of the
Bluetooth ® device.
3. Perform pairing again.
If pairing is not possible after trying
the procedure, turn off the power
of the Bluetooth
® device once, then
turn it back on. If pairing is still
not possible after this, contact an
Authorized Mazda Dealer or Mazda
Bluetooth
® Hands-Free Customer
Service.
*1 Setting which detects the existence of a device external to the Bluetoot\
h
® unit

CX-5_8FN1-EA-16L_Edition1.indb 1282016/12/12 10:06:59

5–137
Interior Features
Appendix
NOTE
  Playback may not be possible
depending on the type and condition of
the USB fl ash memory even if the audio
fi le complies with the standard.
   A copyright protected WMA/AAC fi le
cannot be played in this unit.
   (Type B)  If a fi le name in the USB memory is too
long, it could cause operation problems
such as not being able to playback the
song.
 (Recommended: Within 80 characters)   The order of the music data stored in
the device may differ from the playback
order.
  To prevent loss or damage of stored
data, we recommend that you always
back up your data.
  If a device exceeds the maximum
electric current value of 1,000 mA,
it may not operate or recharge when
connected.
  Do not pull out the USB device while in
the USB mode (only pull it out while in
FM/AM radio mode).
  The device will not operate if the data is
password protected.

MP3/WMA/AAC/OGG *1 fi les written
under speci fi cations other than the
indicated speci fi cation may not play
normally or fi les/folder names may not
display correctly.

*1 Type B
Operating Tips for iPod
This unit supports playback of music fi les
recorded to an iPod.


* iPod is a trademark of Apple Inc., registered in the U.S. and other
countries.

The iPod may not be compatible
depending on the model or OS version. In
this case, an error message is displayed.
CAUTION
 Remove the iPod when it is not in use. Because the iPod is not designed
to withstand excessive changes in
temperature inside the cabin, it could be
damaged or the battery may deteriorate
due to the excessive temperature or
humidity inside the cabin if it is left in the
vehicle.
 If data in the iPod is lost while it is connected to the unit, Mazda cannot
guarantee recovery of any lost data.
 If the iPod battery is deteriorated, the iPod may not recharge and playback
may not be possible when it is connected
to the unit.
 Be careful not to pinch the iPod connecting cable when opening/closing
the center console.
 For details on using the iPod, refer to the iPod instruction manual.
 When connecting the iPod to a USB port, all commands are made from the audio
unit. iPod control is not possible.

NOTE
The audio unit cannot display images or
videos stored in an iPod.

CX-5_8FN1-EA-16L_Edition1.indb 1372016/12/12 10:07:00

6–42
Maintenance and Care
Owner Maintenance
*Some models.
CAUTION
 Do not use your temporary spare tire rim with a snow tire or a conventional
tire. Neither will properly fi t and could
damage both tire and rim.
 The temporary spare tire has a tread life of less than 5,000 km (3,000 miles). The
tread life may be shorter depending on
driving conditions.
 The temporary spare tire is for limited use, however, if the tread wear solid-
band indicator appears, replace the tire
with the same type of temporary spare
(page 6-41 ).

NOTE
Tires degrade over time, even when
they are not being used on the road. It
is recommended that tires generally be
replaced when they are 6 years or older.
Heat caused by hot climates or frequent
high loading conditions can accelerate
the aging process. You should replace the
spare tire when you replace the other road
tires due to the aging of the spare tire. The
period in which the tire was manufactured
(both week and year) is indicated by a
4-digit number.
Refer to Tire Labeling on page 8-25 .

Replacing a Wheel
WARNING
Always use wheels of the correct size on
your vehicle: Using a wrong-sized wheel is
dangerous. Braking and handling
could be aff ected, leading to loss of
control and an accident.

CAUTION
A wrong-sized wheel may adversely
aff ect:
 Tire fi t Wheel and bearing life Ground clearance Snow-chain clearance Speedometer calibration Headlight aim Bumper height Tire Pressure Monitoring System *
NOTE
  When replacing a wheel, make sure
the new one is the same as the original
factory wheel in diameter, rim width,
and offset (inset/outset).
  For details, contact an Authorized
Mazda Dealer.


Proper tire balancing provides the best
riding comfort and helps reduce tread
wear. Out-of-balance tires can cause
vibration and uneven wear, such as
cupping and fl at spots.
CX-5_8FN1-EA-16L_Edition1.indb 422016/12/12 10:07:13

6–45
Maintenance and Care
Owner Maintenance
*Some models.
CAUTION
When removing the lens or lamp unit
using a fl athead screwdriver, make
sure that the fl athead screwdriver does
not contact the interior terminal. If
the fl athead screwdriver contacts the
terminal, a short circuit may occur.

NOTE
  To replace the bulb, contact an
Authorized Mazda Dealer.
  Use the protective cover and carton for
the replacement bulb to dispose of the
old bulb promptly and out of the reach
of children.

Replacing Exterior Light Bulbs
Headlights/Daytime running lights,
Daytime running lights/Parking lights
(Type A), Front side-marker lights
(Type A), Fog lights
* , Brake lights (Type
A), Taillights (Type A), Reverse lights,
High-mount brake light, Side turn
signal lights, Rear side-marker lights
(Type A)
The LED bulb cannot be replaced as a
single unit because it is an integrated unit.
The LED bulb has to be replaced with the
unit. We recommend an Authorized Mazda
Dealer when the replacement is necessary.
Front turn signal lights/Parking lights
1. Make sure the ignition is switched off, and the headlight switch is off.
2. Lift the hood.
Refer to Hood on page 6-20 .
3. Turn the socket and bulb assembly counterclockwise and remove it.
4. Disconnect the bulb from the socket.


5. Install the new bulb in the reverse order of the removal procedure.

Front side-marker lights (Type B)
1. Make sure the ignition is switched off, and the headlight switch is off.
2. If you are changing the right bulb, start the engine, turn the steering wheel all
the way to the left, and turn off engine.
If you are changing the left bulb, turn
the steering wheel to the right.
3. Pull the center of each plastic retainer using a fl athead screwdriver and
remove the retainers, and then partially
peel back the over fender.

Removal
Installation

CX-5_8FN1-EA-16L_Edition1.indb 452016/12/12 10:07:13

6–61
Maintenance and Care
Appearance Care
*Some models.
WARNING
Dry off brakes that have become
wet by driving slowly, releasing the
accelerator pedal and lightly applying
the brakes several times until the brake
performance returns to normal: Driving with wet brakes is dangerous.
Increased stopping distance or the
vehicle pulling to one side when
braking could result in a serious
accident. Light braking will indicate
whether the brakes have been aff ected.

Aluminum Wheel Maintenance *
A protective coating is provided over the
aluminum wheels. Special care is needed
to protect this coating.
CAUTION
Do not use any detergent other than
mild detergent. Before using any
detergent, verify the ingredients.
Otherwise, the product could discolor
or stain the aluminum wheels.

NOTE
  Do not use a wire brush or any abrasive
cleaner, polishing compound, or solvent
on aluminum wheels. They may damage
the coating.
  Always use a sponge or soft cloth to
clean the wheels.
 Rinse the wheels thoroughly with lukewarm or cold water. Also, be sure
to clean the wheels after driving on
dusty or salted roads to help prevent
corrosion.
  Avoid washing your vehicle in an
automatic car wash that uses high-
speed or hard brushes.
  (19-inch wheel vehicle)  If your aluminum wheels lose luster,
apply wax which contains no polishing
powder.

CX-5_8FN1-EA-16L_Edition1.indb 612016/12/12 10:07:17

6–63
Maintenance and Care
Appearance Care
*Some models.
Seat Belt Maintenance
1. Clean the soiled area by lightly dabbing it with a soft cloth soaked in a mild
detergent (approx. 5%) diluted with
water.
2. Wipe off the remaining detergent using a cloth soaked in clean water and
wrung out well.
3. Before retracting seat belts which have been pulled out for cleaning, dry them
off thoroughly and make sure there is
no remaining moisture on them.

WARNING
If a seat belt appears frayed or has
abrasions, have it replaced by an
Authorized Mazda Dealer: If a seat belts is used under such a
condition, it cannot function at its full
capacity which could result in serious
injury or death.

Use a mild detergent to remove soiling
from a seat belt: If organic solvents are used for
cleaning the seat belts or they
become stained or bleached, there
is the possibility of them becoming
weakened and as a result, they may
not function at their full capacity
which could cause serious injury or
death.

NOTE
Clean seat belts diligently if they get
dirty. Leaving them uncleaned will make
it dif fi cult to clean them later, and it may
affect the smooth retracting of the seat
belt.

Vinyl Upholstery Maintenance
Remove dust and dirt from the vinyl
upholstery using a brush or vacuum.
Remove soiling from vinyl upholstery
using a leather and vinyl upholstery
cleaner.
Upholstery Maintenance
1. Clean the soiled area by lightly dabbing it with a soft cloth soaked in a mild
detergent (approx. 5%) diluted with
water.
2. Wipe off the remaining detergent using a cloth soaked in clean water and
wrung out well.

Leather Upholstery Maintenance *
1. Remove dust and sand using a vacuum cleaner.
2. Wipe off the soiled area with a soft cloth and a suitable, special cleaner or
a soft cloth soaked in a mild detergent
(about 5%) diluted with water.
3. Wipe off the remaining detergent using a cloth soaked in clean water and
wrung out well.
4. Remove moisture with a dry, soft cloth and allow the leather to further dry in
a well-ventilated, shaded area. If the
leather gets wet such as from rain,
remove the moisture and dry it as soon
as possible.

CX-5_8FN1-EA-16L_Edition1.indb 632016/12/12 10:07:17

6–65
Maintenance and Care
Appearance Care
*Some models.
Active Driving Display Maintenance *
Windshield type
The dust-proof sheet has a coating. When
cleaning, do not use a hard or rough-
surface cloth, or cleaning detergent. In
addition, if a chemical solvent gets on
the active driving display, wipe it off
immediately. The dust-proof sheet could
be damaged and the surface coating could
be scratched. Use a fi ne, soft cloth such as
those used for cleaning eyeglasses.
NOTE
Use of compressed air when cleaning the
dust-proof sheet is recommended.

Auto fl ip-up type
The combiner and mirror surface have
a special coating. When cleaning it, do
not use a hard cloth, a cloth with a rough
surface, or cleaning detergent. Use a fi ne-
textured, soft cloth. .
If a chemical solvent gets on the combiner
or mirror surface, wipe it off immediately.
Otherwise, they could be damaged and the
surface coating could be scratched.
Cleaning the Window Interiors
If the windows become covered with an
oily, greasy, or waxy fi lm, clean them with
glass cleaner. Follow the directions on the
container.
CAUTION
 Do not scrape or scratch the inside of the window glass. It could damage the
thermal fi laments and the antenna lines.
 When washing the inside of the window glass, use a soft cloth dampened in
lukewarm water, gently wiping the
thermal fi laments and the antenna lines.
 Use of glass cleaning products could damage the thermal fi laments and the
antenna lines.

Cleaning the Floor Mats
Rubber fl oor mats should be cleaned with
mild soap and water only.
WARNING
Do not use rubber cleaners, such as tire
cleaner or tire shine, when cleaning
rubber fl oor mats: Cleaning the rubber fl oor mats with
rubber cleaning products makes the
fl oor mats slippery.
This may cause an accident when
depressing the accelerator, brake, or
clutch (Manual transaxle) pedal or
when getting in or out of the vehicle.

After removing the fl oor mats for cleaning,
always reinstall them securely (page
3-51 ).

CX-5_8FN1-EA-16L_Edition1.indb 652016/12/12 10:07:18

7–27
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.
Signal Warning


(Red)
Brake Pedal
Operation Demand Warning Light
*
When only fl ashing
Flashes if there is the possibility of the vehicle not being held in the\
stopped position by the
AUTOHOLD function, such as on steep slopes. Depress and hold your foot on t\
he brake
pedal.
When fl ashing and beep sound is activated at the same time
The warning light fl ashes and the beep sound is activated for about fi ve seconds if there is
a problem with the system. If the warning light fl ashes and the warning sound is activated,
immediately depress the brake pedal and stop using the AUTOHOLD function then contact
an Authorized Mazda Dealer.
WARNING
Immediately depress the brake pedal if the warning light fl ashes and the beep sound is
activated while using the AUTOHOLD function: Because the AUTOHOLD function is canceled forcibly, the vehicle may move
unexpectedly and result in an accident.


Check Engine Light If this light illuminates while driving, the vehicle may have a problem.\
It is important to
note the driving conditions when the light illuminated and consult an Authorized Mazda
Dealer.
The check engine light may illuminate in the following cases:
 The fuel tank level being very low or approaching empty.
 The engine's electrical system has a problem.
 The emission control system has a problem.
 The fuel- fi ller cap is missing or not tightened securely.
If the check engine light remains on, or it fl ashes continuously , do not drive at high speeds
and consult an Authorized Mazda Dealer as soon as possible.


Automatic
Transaxle Warning
Indication/Warning Light
* The indication/light illuminates when the transaxle has a problem.
CAUTION
If the automatic transaxle warning indication/light illuminates, the transaxle has
an electrical problem. Continuing to drive your Mazda in this condition could cause
damage to your transaxle. Consult an Authorized Mazda Dealer as soon as possible.


AWD Warning Indication
*
“4WD System Malfunction” is displayed
The indication is displayed under the following conditions. The system may have a
malfunction. Have the vehicle checked at an Authorized Mazda Dealer.
 When there is a malfunction in the AWD system.
 When there is a large difference between the tire size of the front and rear wheels.
“4WD System High Load” is displayed
The indication is displayed under the following conditions. Park the veh\
icle in a safe place
and check that the warning indication light turns off, and then drive the vehicle. Contact an
Authorized Mazda Dealer if the indication is continuously displayed.
 When the differential oil temperature is excessively high.
 When there is a large difference between the front and rear wheel rotation, such as when
trying to remove the vehicle from mud.
CX-5_8FN1-EA-16L_Edition1.indb 272016/12/12 10:07:25