2017 MAZDA MODEL CX-5 maintenance

6–27
Maintenance and Care
Owner Maintenance
Brake/Clutch Fluid
Inspecting Brake/Clutch Fluid Level
WARNING
If the brake/clutch fl uid level is low, have
the brakes inspected:
A low brake/clutch fl uid level is
dangerous.
A low level could indicate brake lining
wear or a brake system leak which
could cause the brakes to fail and lead
to an accident.

The brakes and clutch draw fl uid from the
same reservoir.
Inspect the fl uid level in the reservoir
regularly. It should be kept between the
MAX and MIN lines.
The level normally drops with
accumulated distance, a condition
associated with wear of brake and clutch
linings. If it is excessively low, have
the brake/clutch system inspected by an
Authorized Mazda Dealer.


Washer Fluid
Inspecting Washer Fluid Level
WARNING
Use only windshield washer fl uid or
plain water in the reservoir: Using radiator antifreeze as washer
fl uid is dangerous. If sprayed on the
windshield, it will dirty the windshield,
aff ect your visibility, and could result in
an accident.

Using Washer Fluid Without Anti-freeze
Protection in Cold Weather: Operating your vehicle in temperatures
below 4 degrees C (40 degrees F)
using washer fl uid without anti-freeze
protection is dangerous as it could
cause impaired windshield vision and
result in an accident. In cold weather,
always use washer fl uid with anti-
freeze protection.

NOTE
State or local regulations may restrict the
use of volatile organic compounds (VOCs),
which are commonly used as anti-freeze
agents in washer fl uid. A washer fl uid with
limited VOC content should be used only
if it provides adequate freeze resistance
for all regions and climates in which the
vehicle will be operated.

CX-5_8FN1-EA-16L_Edition1.indb 272016/12/12 10:07:08

6–28
Maintenance and Care
Owner Maintenance
Inspect fl uid level in the washer fl uid
reservoir; add fl uid if necessary.

L F
OK
The top of the fl oat should be between F
and L.

Use plain water if washer fl uid is
unavailable.
But use only washer fl uid in cold weather
to prevent it from freezing.
NOTE
Front and rear washer fl uid is supplied
from the same reservoir.

Body Lubrication
All moving points of the body, such as
door and hood hinges and locks, should
be lubricated each time the engine oil is
changed. Use a nonfreezing lubricant on
locks during cold weather.

Make sure the hood's secondary latch
keeps the hood from opening when the
primary latch is released.
CX-5_8FN1-EA-16L_Edition1.indb 282016/12/12 10:07:09

6–29
Maintenance and Care
Owner Maintenance
Wiper Blades
CAUTION
 Hot waxes applied by automatic car washers have been known to aff ect the
wiper's ability to clean windows.
 To prevent damage to the wiper blades, do not use gasoline, kerosene, paint
thinner, or other solvents on or near
them.
 When the wiper lever is in the AUTO position and the ignition is switched ON,
the wipers may move automatically in
the following cases:
 If the windshield above the rain sensor is touched.
 If the windshield above the rain sensor is wiped with a cloth.
 If the windshield is struck with a hand or other object.
 If the rain sensor is struck with a hand or other object from inside the vehicle.
 Be careful not to pinch hands or fi ngers as it may cause injury, or damage the
wipers. When washing or servicing the
vehicle, make sure the wiper lever is in
the OFF position.

Contamination of either the windshield or
the blades with foreign matter can reduce
wiper effectiveness. Common sources are
insects, tree sap, and hot wax treatments
used by some commercial car washes.

If the blades are not wiping properly,
clean the window and blades with a good
cleaner or mild detergent; then rinse
thoroughly with clean water. Repeat if
necessary.
Replacing Windshield Wiper Blades
When the wipers no longer clean well, the
blades are probably worn or cracked.
Replace them.
CAUTION
 To prevent damage to the wiper arms
and other components, do not try to
sweep the wiper arm by hand.
 Do not bend the blade rubber unnecessarily when replacing it.
Otherwise, the metal stiff ener in the
blade may deform and the windshield
wiper operation may be adversely
aff ected.

NOTE
When raising both windshield wiper arms,
raise the driver's side wiper arm fi rst.
When lowering the wiper arms, slowly
lower the wiper arm from the passenger's
side fi rst while supporting it with your
hand. Forcefully lowering the wiper arms
could damage the wiper arm and blade,
and may scratch or crack the windshield.

CX-5_8FN1-EA-16L_Edition1.indb 292016/12/12 10:07:09

6–30
Maintenance and Care
Owner Maintenance
1. Raise the wiper arm.
CAUTION
To prevent damage to the windshield
let the wiper arm down easily, do not
let it slap down on the windshield.

2. Slide the blade component in the direction of the arrow while pressing
the wiper arm tab to remove the blade
component from the wiper arm.


3. Pull the blade rubber in the direction
of the arrow and slide it to a position
where the blade holder groove can be
checked.

Groove
CX-5_8FN1-EA-16L_Edition1.indb 302016/12/12 10:07:09

6–31
Maintenance and Care
Owner Maintenance
4. Pull the end of the blade rubber from the blade holder groove in the direction
of the arrow and remove the blade
rubber from the blade holder.


Groove
5. Insert the end of the new blade rubber
into the groove of the blade holder until
it contacts the end of the blade holder.


Groove

CX-5_8FN1-EA-16L_Edition1.indb 312016/12/12 10:07:09

6–32
Maintenance and Care
Owner Maintenance
6. After pulling the blade rubber in the direction of the arrow and sliding the
blade rubber to a position to check the
blade holder groove, slide the blade
rubber end in the opposite direction.


Groove

7. Make sure that the blade rubber is correctly installed to the blade holder.
8. Align the wiper arm tabs with the blade component grooves.


Tabs
Grooves
9. Align the blade component projection
with the wiper arm notch.


Notch
Projection

10. Slide the blade component and install it to the wiper arm.



11. Slowly lower the wiper arm onto the windshield.

Replacing Rear Window Wiper Blade
When the wiper no longer cleans well, the
blade is probably worn or cracked.
Replace it.
CAUTION
To prevent damage to the wiper arm
and other components, do not move
the wiper by hand.

CX-5_8FN1-EA-16L_Edition1.indb 322016/12/12 10:07:10

6–33
Maintenance and Care
Owner Maintenance
1. Remove the cover and raise the wiper arm.


2. Firmly rotate the wiper blade to the right until it unlocks, then remove the
blade.


CAUTION
To prevent damage to the rear window,
do not let the wiper arm fall on it.

3. Pull down the blade rubber and slide it out of the blade holder.


4. Remove the metal stiffeners from the blade rubber and install them in the
new blade.


CAUTION
Do not bend or discard the stiff eners.
You need to use them again.

5. Carefully insert the new blade rubber.
Then install the blade assembly in the reverse order of removal.


CX-5_8FN1-EA-16L_Edition1.indb 332016/12/12 10:07:10

6–34
Maintenance and Care
Owner Maintenance
Battery
WARNING
Wash hands after handling the battery and related accessories: Battery posts, terminals and related accessories contain lead and lead compounds,
chemicals known to the State of California to cause cancer and reproductive harm.


Read the following precautions carefully before using the battery or inspecting
to ensure safe and correct handling:

Always wear eye protection when working near the battery:
Working without eye protection is dangerous. Battery fl uid contains SULFURIC ACID
which could cause blindness if splashed into your eyes. Also, hydrogen gas produced
during normal battery operation, could ignite and cause the battery to explode.


Wear eye protection and protective gloves to prevent contact with battery fl uid:
Spilled battery fl uid is dangerous.
Battery fl uid contains SULFURIC ACID which could cause serious injuries if it gets in eyes,
or on the skin or clothing. If this happens, immediately fl ush your eyes with water for
15 minutes or wash your skin thoroughly and get medical attention.


Always keep batteries out of the reach of children:
Allowing children to play near batteries is dangerous. Battery fl uid could cause serious
injuries if it gets in the eyes or on the skin.


Keep fl ames and sparks away from open ba ttery cells and do not allow metal
tools to contact the positive (
) or negative ( ) terminal of the battery when working
near a battery. Do not allow the positive (
) terminal to contact the vehicle body:
Flames and sparks near open battery cells are dangerous. Hydrogen gas, produced
during normal battery operation, could ignite and cause the battery to explode. An
exploding battery can cause serious burns and injuries. Keep all fl ames including
cigarettes and sparks away from open battery cells.

CX-5_8FN1-EA-16L_Edition1.indb 342016/12/12 10:07:11