2017 MAZDA MODEL CX-5 turn signal

5–24
Interior Features
Audio Set [Type A (non-touchscreen)]
Operating the Radio
Band selector buttonChannel preset
buttons
Scan button Auto memory button
Tuning button Audio display

Radio ON
Press a band selector button ( ) to
turn the radio on.
Band selection
Successively pressing the band selector
button (
) switches the bands as
follows: FM1→FM2→AM.

The selected mode will be indicated.
NOTE
If the FM broadcast signal becomes weak,
reception automatically changes from
STEREO to MONO for reduced noise.

Tuning
The radio has the following tuning
methods: Manual, Seek, Scan, Preset
channel, and Auto memory tuning. The
easiest way to tune stations is to set them
on preset channels.
Manual tuning
Select the station by pressing the tuning
button (
, ) lightly.
Seek tuning
Automatic search for radio stations starts
when the tuning button (
, ) is pressed
until a beep sound is heard. The search
stops when a station is found.
NOTE
If you continue to press and hold the
button, the frequency will continue
changing without stopping.

CX-5_8FN1-EA-16L_Edition1.indb 242016/12/12 10:06:29

5–79
Interior Features
Audio Set [Type B (touchscreen)]
NOTE
  If an analog broadcast is received once
and
is received while HD1 is
selected, the audio unit switches to the

station automatically.
   When the icon is illuminated, there
could be a noticeable difference in
sound quality and volume when a
change from digital to analog signals
occurs. If the sound quality and volume
become noticeably diminished or cut
off, select the
icon to turn off

( icon is not illuminated).   Once an analog broadcast is received
when HD1 is selected from the Favorite
channels, it is switched to

automatically. If the radio reception
conditions are poor, or HD is off,
switching to
broadcasts is
not possible.
   When an HD specialty channel (HD2 to
HD8) is selected from the Favorite
channels, “Signal Lost” is displayed
and no audio is output until

is received. If the radio reception
conditions are poor, “Signal Lost”
continues to be displayed.
   If the icon is not illuminated,
information such as song titles of the

station are received,
however, the audio output is analog.

iTunes Tagging (for Apple devices with
USB use only)
By tagging a song currently being aired,
the song can later be purchased from
the iTunes Store. One hundred tags
can be stored. A maximum of 100 tags
(for 100 songs) can be stored for later
downloading.

1. Select the icon. The tag is stored in
the audio unit.
2. Connect the device via the vehicle's USB. Any stored tag(s) will be sent
automatically to the connected device.
3. Once at home or after parking the vehicle safely, log onto the iTunes
Store with your device. Your previously
tagged song(s) can now be easily
purchased.

NOTE
  Both AM and FM can be
used.
   Because iTunes tagging only supports
purchases from the iTunes Store, direct
downloading of music from the vehicle's
audio unit is not possible.
  If the available memory for the
connected device is insuf fi cient, the tag
is not sent.
   If an error occurs while the tag is being
sent, reconnect the device.

CX-5_8FN1-EA-16L_Edition1.indb 792016/12/12 10:06:42

6–44
Maintenance and Care
Owner Maintenance
Light Bulbs

Side turn signal lights
Vanity mirror
lights Type A
Type B
Overhead lights/Front map
lights
Side turn signal lights Vanity mirror lights
Overhead lights/Front map
lights Front turn signal lights/Parking
lights
Rear turn signal lights
License plate lights Luggage compartment
light
Reverse lights
Brake lights/Taillights
Brake lights
High-mount
brake light Rear map lights
Rear turn signal lights
License plate lights
Luggage compartment
lightReverse lights
Brake lights/Taillights/Rear
side-marker lights High-mount brake light
Rear map lights
Fog lights
Headlights (High/Low beam)
/Daytime running lights
Front side-marker lights
Rear side-marker lights
Daytime running lights/Parking
lights
Front turn signal
lights/Parking lights Fog lights Front side-marker lights
Some models.
Headlights (High/Low beam)
/Daytime running lights

CX-5_8FN1-EA-16L_Edition1.indb 442016/12/12 10:07:13

6–45
Maintenance and Care
Owner Maintenance
*Some models.
CAUTION
When removing the lens or lamp unit
using a fl athead screwdriver, make
sure that the fl athead screwdriver does
not contact the interior terminal. If
the fl athead screwdriver contacts the
terminal, a short circuit may occur.

NOTE
  To replace the bulb, contact an
Authorized Mazda Dealer.
  Use the protective cover and carton for
the replacement bulb to dispose of the
old bulb promptly and out of the reach
of children.

Replacing Exterior Light Bulbs
Headlights/Daytime running lights,
Daytime running lights/Parking lights
(Type A), Front side-marker lights
(Type A), Fog lights
* , Brake lights (Type
A), Taillights (Type A), Reverse lights,
High-mount brake light, Side turn
signal lights, Rear side-marker lights
(Type A)
The LED bulb cannot be replaced as a
single unit because it is an integrated unit.
The LED bulb has to be replaced with the
unit. We recommend an Authorized Mazda
Dealer when the replacement is necessary.
Front turn signal lights/Parking lights
1. Make sure the ignition is switched off, and the headlight switch is off.
2. Lift the hood.
Refer to Hood on page 6-20 .
3. Turn the socket and bulb assembly counterclockwise and remove it.
4. Disconnect the bulb from the socket.


5. Install the new bulb in the reverse order of the removal procedure.

Front side-marker lights (Type B)
1. Make sure the ignition is switched off, and the headlight switch is off.
2. If you are changing the right bulb, start the engine, turn the steering wheel all
the way to the left, and turn off engine.
If you are changing the left bulb, turn
the steering wheel to the right.
3. Pull the center of each plastic retainer using a fl athead screwdriver and
remove the retainers, and then partially
peel back the over fender.

Removal
Installation

CX-5_8FN1-EA-16L_Edition1.indb 452016/12/12 10:07:13

6–46
Maintenance and Care
Owner Maintenance
4. Pull the center of each plastic retainer using a fl athead screwdriver and
remove the retainers, and then partially
peel back the mudguard.

Removal
Installation

5. Turn the socket and bulb assembly counterclockwise and remove it.
6. Disconnect the bulb from the socket.


7. Install the new bulb in the reverse order of the removal procedure.

Rear turn signal lights, Brake lights/
Taillights/Rear side-marker lights (Type
B)
1. Make sure the ignition is switched off, and the turn signal switch is off.
2. Wrap a small fl athead screwdriver with
a soft cloth to prevent damage to the
cover, and then remove the cover with
the fl athead screwdriver.


3. Turn the bolts counterclockwise and remove them.


CX-5_8FN1-EA-16L_Edition1.indb 462016/12/12 10:07:14

6–47
Maintenance and Care
Owner Maintenance
4. Pull the unit rearward to remove it.

5. Turn the socket and bulb assembly counterclockwise and remove it.
6. Disconnect the bulb from the socket.
Rear turn signal lights


Brake lights/Taillights/Rear side- marker lights


7. Install the new bulb in the reverse order of the removal procedure.

License plate lights
1. Make sure the ignition is switched off, and the headlight switch is off.
2. Wrap a fl athead screwdriver with a soft
cloth to prevent damage to the lens,
and then remove the lens by carefully
prying on the edge of the lens with a
fl athead screwdriver.
3. Disconnect the bulb by pulling it out.


4. Install the new bulb in the reverse order of the removal procedure.

CX-5_8FN1-EA-16L_Edition1.indb 472016/12/12 10:07:14

6–53
Maintenance and Care
Owner Maintenance
*Some models.
DESCRIPTION FUSE
RATING PROTECTED COMPONENT
14 FAN GE 30 A Cooling fan
15 ENG.MAIN 40 A Engine control system
16 ABS/DSC M 50 A ABS, Dynamic stability control system
17 FAN DE 40 A —
18 WIPER 20 A Front window wiper and washer
19 HEATER 40 A Air conditioner
20 ADD FAN GE 30 A Cooling fan
21 ENGINE.IG1 7.5 A Engine control system
22 C/U IG1 15 A For protection of various circuits
23 AUDIO2 7.5 A Audio system
24 METER2 7.5 A —
25 ENGINE3 15 A Engine control system
26 ENGINE2 15 A Engine control system
27 ENGINE1 15 A Engine control system
28 AT 15 A Transaxle control system
* , Ignition switch
29 H/CLEAN 20 A —
30 A/C 7.5 A Air conditioner
31 AT PUMP 15 A Transaxle control system
*
32 HORN 15 A Horn
33 R.WIPER 15 A Rear window wiper
34 H/L HI 20 A Headlight high beam
35 ST.HEATER 15 A Heated steering wheel
*
36 FOG 15 A Fog lights *
37
7.5 A Engine control system
38 H/L LOW L 15 A Headlight low beam (LH)
39 ENGINE4 15 A —
40 — — —
41 METER1 10 A Instrument cluster
42 SRS1 7.5 A Air bag
43 BOSE 25 A Bose
® Sound System-equipped model *
44 AUDIO1 15 A Audio system
45 ABS/DSC S 30 A ABS, Dynamic stability control system
46 FUEL PUMP 15 A Fuel system
47 FUEL WARM 25 A —
48 TAIL 15 A Taillights, License plate lights
49 SCR2
FUEL PUMP2 25 A
—
50 HAZARD 25 A Hazard warning
fl ashers, Turn signal lights/Front side-marker
lights, Parking lights
CX-5_8FN1-EA-16L_Edition1.indb 532016/12/12 10:07:16

7–2
If Trouble Arises
Parking in an Emergency
Parking in an Emergency
The hazard warning lights should always
be used when you stop on or near a
roadway in an emergency.


The hazard warning lights warn other
drivers that your vehicle is a traf fi c hazard
and that they must take extreme caution
when near it.



Depress the hazard warning fl asher and
all the turn signals will fl ash. The hazard
warning indicator lights in the instrument
cluster fl ash simultaneously.
NOTE
  The turn signals do not work when the
hazard warning lights are on.
  Check local regulations about the use of
hazard warning lights while the vehicle
is being towed to verify that it is not in
violation of the law.

CX-5_8FN1-EA-16L_Edition1.indb 22016/12/12 10:07:18