2017 MAZDA MODEL CX-5 roof

4–29
When Driving
Instrument Cluster and Display
CAUTION
 (With Auto Flip-up Type)  Do not try to adjust the angle or open/close the active driving display manually.
Fingerprints on the display will make it diffi cult to view and using excessive force when
operating it could cause damage.
 (With Auto Flip-up Type)  Do not place objects in the vicinity of the active driving display. The active driving display
may not operate or any interference with its operation could cause damage.
 Do not place beverages near the active driving display. If water or other liquids are splashed on the active driving display, it could cause damage.
 Do not place objects above the active driving display or apply stickers to the dust-proof sheet/optical receiver as they will cause interference.
 A sensor is integrated to control the display's luminosity. If the optical receiver is covered, the display's luminosity will lower making the display diffi cult to view.
 Do not allow intense light to hit the optical receiver. Otherwise, it could cause damage.
NOTE
   Wearing polarized sunglasses will reduce the visibility of the active driving display due to
the characteristics of the display.
  If the battery has been removed and re-installed or the battery voltage is low, the adjusted
position may deviate.
  The display may be dif fi cult to view or temporarily affected by weather conditions such as
rain, snow, light, and temperature.
   If the audio system is removed, the active driving display cannot be operated.
CX-5_8FN1-EA-16L_Edition1.indb 292016/12/12 10:05:46

4–159
When Driving
i-ACTIVSENSE
  In the following cases, the Forward Sensing Camera (FSC) may not be able to detect
target objects correctly.
  Under bad weather condition, such as rain, fog and snow.  The window washer is being used or the windshield wipers are not used when it's
raining.
  Ice, fog, snow, frost, rainfall, dirt, or foreign matter such as a plastic bag is stuck on
the windshield.
  Trucks with low loading platforms and vehicles with an extremely low or high pro fi le.   When driving next to walls with no patterning (including fences and lon\
gitudinally
striped walls).
  The taillights of the vehicle ahead are turned off.  A vehicle is outside the illumination range of the headlights.  The vehicle is making a sharp turn, or ascending or descending a steep s\
lope.  Entering or exiting a tunnel.  Heavy luggage is loaded causing the vehicle to tilt.  Strong light is shone at the front of the vehicle (back light or high-beam light from on-
coming vehicles).
  There are many light emitters on the vehicle ahead.  When the vehicle ahead is not equipped with taillights or the taillights\
are turned off at
nighttime.
  Elongated luggage or cargo is loaded onto installed roof rails and covers the Forward
Sensing Camera (FSC).
  Exhaust gas from the vehicle in front, sand, snow, and water vapor rising from
manholes and grating, and water splashed into the air.
  When towing a malfunctioning vehicle.  The vehicle is driven with tires having signi fi cantly different wear.   The vehicle is driven on down slopes or bumpy roads.  There are water puddles on the road.  The surroundings are dark such as during the night, early evening, or early morning,
or in a tunnel or indoor parking lot.
  The illumination brightness of the headlights is reduced or the headlight illumination
is weakened due to dirt or a deviated optical axis.
  The target object enters the blind spot of the Forward Sensing Camera (FSC).  A person or object bursts onto the road from the shoulder or cuts right in front of you.  You change lanes and approach a vehicle ahead.  When driving extremely close to the target object.  Tire chains or a temporary spare tire is installed.  The vehicle ahead has a special shape. For example, a vehicle towing a t\
railer house
or a boat, or a vehicle carrier carrying a vehicle with its front pointed rearward.

CX-5_8FN1-EA-16L_Edition1.indb 1592016/12/12 10:06:17

4–176
When Driving
Rear View Monitor
*Some models.
Rear View Monitor *
The rear view monitor provides visual images of the rear of the vehicle \
when reversing.
WARNING
Always drive carefully confi rming the safety of the rear and the surrounding conditions
by looking directly with your eyes: Reversing the vehicle by only looking at the screen is dangerous as it may cause an
accident or a collision with an object. The rear view monitor is only a visual assist device
when reversing the vehicle. The images on the screen may be diff erent from the actual
conditions.

CAUTION
 Do not use the rear view monitor under the following conditions: Using the rear view monitor under the following conditions is dangerous and could result in injury or vehicle
damage or both.
 Icy or snow-covered roads. Tire chains or a temporary spare tire is installed. The liftgate is not fully closed. The vehicle is on a road incline.  When the display is cold, images may course across the monitor or the screen and may be dimmer than usual, which could cause diffi culty in confi rming the surrounding conditions
of the vehicle. Always drive carefully confi rming the safety of the rear and the surrounding
conditions by looking directly with your eyes.
 Do not apply excessive force to the camera. The camera position and angle may deviate. Do not disassemble, modify, or remove it as it may no longer be waterproof. The camera cover is made of plastic. Do not apply degreasing agents, organic solvents, wax, or glass coating agents to the camera cover. If any are spilled on the cover, wipe off
with a soft cloth immediately.
 Do not rub the camera cover forcefully with an abrasive or hard brush. The camera cover or lens may be scratched which might aff ect the images.

CX-5_8FN1-EA-16L_Edition1.indb 1762016/12/12 10:06:20

5–61
Interior Features
Audio Set [Type A (non-touchscreen)]
Commands useable anytime during
voice recognition
“Help” or “Go Back” are commands
which can be used at anytime during voice
recognition.
Help function use
The help function informs the user of all
the available voice commands under the
current conditions.

1. Say: [Beep] “Help”
2. Follow the prompts to receive the appropriate voice guidance instructions.

Returning to previous operation
This command is for returning to the
previous operation while in the voice
recognition mode.
Say: [Beep] “Go Back”
To prevent a deterioration in the voice
recognition rate and voice quality, the
following points should be observed:
  The voice recognition cannot be
performed while voice guidance or
the beep sound is operating. Wait
until the voice guidance or the beep
sound is fi nished before saying your
commands.
   Dialects or different wording other
than hands-free prompts cannot be
recognized by voice recognition. Speak
in the wording speci fi ed by the voice
commands.
   It is not necessary to face the
microphone or approach it. Speak the
voice commands while maintaining a
safe driving position.
   Do not speak too slow or too loud.  Speak clearly, without pausing between
words or numbers.
   Close the windows and/or the moonroof
to reduce loud noises from outside
the vehicle, or turn down the air fl ow
of the air-conditioning system while
Bluetooth
® Hands-Free is being used.   Make sure the vents are not directing air
up towards the microphone.

NOTE
If the voice recognition performance is not
satisfactory.
Refer to Voice Recognition Learning
Function (Speaker Enrollment) (Type A)
on page 5-62 .
Refer to Troubleshooting on page 5-65 .

CX-5_8FN1-EA-16L_Edition1.indb 612016/12/12 10:06:35

5–121
Interior Features
Audio Set [Type B (touchscreen)]
Voice Recognition
Basic Operation Method
Activating Voice Recognition
Press the talk button.
Ending Voice Recognition
Use one of the following methods:
  Press the hang-up button.  Say, “Cancel”.  Operate the commander switch or the
center display (only when vehicle is
stopped).

Skipping Voice Guidance (for faster
operation)
Press and release the talk button.
Troubleshooting for Voice Recognition
If you do not understand an operation
method while in the voice recognition
mode, say “Tutorial” or “Help”.
Commands useable anytime during
voice recognition
“Go Back” and “Cancel” are commands
which can be used at anytime during voice
recognition.
Returning to previous operation
To return to the previous operation, say,
“Go Back” while in voice recognition
mode.
Cancel
To put the Bluetooth
® Hands-Free system
in standby mode, say, “Cancel” while in
voice recognition mode.
To prevent a deterioration in the voice
recognition rate and voice quality, the
following points should be observed:
   The voice recognition cannot be
performed while voice guidance or
the beep sound is operating. Wait
until the voice guidance or the beep
sound is fi nished before saying your
commands.
   Phone related commands are available
only when your phone is connected via
Bluetooth
® . Make sure your phone is
connected via Bluetooth ® before you
operate phone related voice commands.
   Music play commands, such as Play
Artist and Play Album can be used only
in USB audio mode.
   Do not speak too slowly or loudly (no
loud voice).
   Speak clearly, without pausing between
words or numbers.
   Dialects or different wording other
than hands-free prompts cannot be
recognized by voice recognition. Speak
in the wording speci fi ed by the voice
commands.
   It is not necessary to face the
microphone or approach it. Speak the
voice commands while maintaining a
safe driving position.
   Close the windows and/or the moonroof
to reduce loud noises from outside the
vehicle, or turn down the air fl ow of the
climate control system while Bluetooth
®
Hands-Free is being used.
   Make sure the vents are not directing air
up towards the microphone.

NOTE
If the voice recognition performance is not
satisfactory.
Refer to Troubleshooting on page 5-127 .

CX-5_8FN1-EA-16L_Edition1.indb 1212016/12/12 10:06:58

6–54
Maintenance and Care
Owner Maintenance
*Some models.
DESCRIPTION FUSE
RATING PROTECTED COMPONENT
51 H/L LOW R 15 A Headlight low beam (RH)
52 OUTLET 25 A Accessory sockets
53 STOP 10 A Brake lights
54 ROOM 15 A Overhead light

Fuse block (Left side)


DESCRIPTION FUSE
RATING PROTECTED COMPONENT
1 P.SEAT D 30 A Power seat
*
2 P.WINDOW3 30 A —
3 R.OUTLET3 15 A Accessory sockets
4 P.WINDOW2 25 A Power windows
5 ESCL 15 A Electronic steering lock
*
6 D.LOCK 25 A Power door locks
7 SEAT WARM 20 A Seat warmer
*
8 SUNROOF 10 A Moonroof *
9 F.OUTLET 15 A Accessory sockets
10 MIRROR 7.5 A Power control mirror
CX-5_8FN1-EA-16L_Edition1.indb 542016/12/12 10:07:16

6–58
Maintenance and Care
Appearance Care
Maintaining the Finish
Washing
CAUTION
 When the wiper lever is in the
position and the ignition is switched ON,
the wipers may move automatically in
the following cases:
 If the windshield above the rain sensor is touched or wiped with a
cloth.
 If the windshield is struck with a hand or other object from either outside or
inside the vehicle.
 Keep hands and scrapers clear of the windshield when the wiper lever is in the

position and the ignition is
switched ON as fi ngers could be pinched
or the wipers and wiper blades damaged
when the wipers activate automatically.
 If you are going to clean the windshield, be sure the wipers are turned off
completely (when it is most likely
that the engine is left running) this is
particularly important when clearing ice
and snow.
 Do not spray water in the engine compartment. Otherwise, it could result
in engine-starting problems or damage
to electrical parts.
 When washing and waxing the vehicle, be careful not to apply excessive force
to any single area of the vehicle roof.
Otherwise, you could dent the vehicle.

To help protect the fi nish from rust
and deterioration, wash your Mazda
thoroughly and frequently, at least once a
month, with lukewarm or cold water.
If the vehicle is washed improperly, the
paint surface could be scratched. Here are
some examples of how scratching could
occur.

Scratches occur on the paint surface when:
 
 The vehicle is washed without fi rst
rinsing off dirt and other foreign matter.
   The vehicle is washed with a rough, dry,
or dirty cloth.
   The vehicle is washed at a car wash that
uses brushes that are dirty or too stiff.
   Cleansers or wax containing abrasives
are used.

NOTE
   Mazda is not responsible for scratches
caused by automatic car washes or
improper washing.
  Scratches are more noticeable on
vehicles with darker paint fi nishes.

To minimize scratches on the vehicle's
paint fi nish:
  Rinse off any dirt or other foreign matter
using lukewarm or cold water before
washing.
   Use plenty of lukewarm or cold water
and a soft cloth when washing the
vehicle. Do not use a nylon cloth.
   Rub gently when washing or drying the
vehicle.
   Take your vehicle only to a car wash
that keeps its brushes well maintained.
   Do not use abrasive cleansers or wax
that contain abrasives.

CX-5_8FN1-EA-16L_Edition1.indb 582016/12/12 10:07:17

6–65
Maintenance and Care
Appearance Care
*Some models.
Active Driving Display Maintenance *
Windshield type
The dust-proof sheet has a coating. When
cleaning, do not use a hard or rough-
surface cloth, or cleaning detergent. In
addition, if a chemical solvent gets on
the active driving display, wipe it off
immediately. The dust-proof sheet could
be damaged and the surface coating could
be scratched. Use a fi ne, soft cloth such as
those used for cleaning eyeglasses.
NOTE
Use of compressed air when cleaning the
dust-proof sheet is recommended.

Auto fl ip-up type
The combiner and mirror surface have
a special coating. When cleaning it, do
not use a hard cloth, a cloth with a rough
surface, or cleaning detergent. Use a fi ne-
textured, soft cloth. .
If a chemical solvent gets on the combiner
or mirror surface, wipe it off immediately.
Otherwise, they could be damaged and the
surface coating could be scratched.
Cleaning the Window Interiors
If the windows become covered with an
oily, greasy, or waxy fi lm, clean them with
glass cleaner. Follow the directions on the
container.
CAUTION
 Do not scrape or scratch the inside of the window glass. It could damage the
thermal fi laments and the antenna lines.
 When washing the inside of the window glass, use a soft cloth dampened in
lukewarm water, gently wiping the
thermal fi laments and the antenna lines.
 Use of glass cleaning products could damage the thermal fi laments and the
antenna lines.

Cleaning the Floor Mats
Rubber fl oor mats should be cleaned with
mild soap and water only.
WARNING
Do not use rubber cleaners, such as tire
cleaner or tire shine, when cleaning
rubber fl oor mats: Cleaning the rubber fl oor mats with
rubber cleaning products makes the
fl oor mats slippery.
This may cause an accident when
depressing the accelerator, brake, or
clutch (Manual transaxle) pedal or
when getting in or out of the vehicle.

After removing the fl oor mats for cleaning,
always reinstall them securely (page
3-51 ).

CX-5_8FN1-EA-16L_Edition1.indb 652016/12/12 10:07:18